User Manual for Beijing Microlight Internet Technology models including: Q340, 2AZ99-Q340, 2AZ99Q340, Q340 Embedded QR Code Card Reader, Embedded QR Code Card Reader
Beijing Microlight Internet Technology Co., LTD. Q340 Embedded QR code/card reader 2AZ99-Q340 2AZ99Q340 q340
File Info : application/pdf, 17 Pages, 993.61KB
DocumentDocumentQ340 User Manual Fast recognition Various output interface Suitable for kiosk, turnstiles etc 1 Beijing Vguang Internet Technology Co., Ltd Disclaimer Before using the product, please read all the contents in this Product Manual carefully to ensure the safe and effective use of the product. Do not disassemble the product or tear up the seal on the device by yourself, or Beijing Vguang Internet Technology Co., Ltd. will not be responsible for the warranty or replacement of the product. The pictures in this manual are for reference only. If any individual pictures do not match the actual product, the actual product shall prevail. For the upgrade and update of this product, Beijing Vguang Internet Technology Co., Ltd. reserves the right to modify the document at any time without notice. Using the product is at the user's own risk. To the maximum extent permitted by applicable law, damages and risks arising from the use or inability to use this product, including but not limited to direct or indirect personal damage, loss of commercial profits, Beijing vguang Internet Technology Co., Ltd. will not bear any responsibility for trade interruption, loss of business information or any other economic loss. All rights of interpretation and modification of this manual belong to Beijing Vguang Internet Technology Co., Ltd. 2 Edit history Change date 2021.5.15 Version V1.0 Description Initial version Responsible 3 Catalog Disclaimer......................................................................................................................................................... 2 1. Preface.......................................................................................................................................................... 5 1.1. Product introduction........................................................................................................................5 1.2. Product feature..................................................................................................................................5 1.3. FCC Warning Statement..................................................................................................................6 2. Product appearance..................................................................................................................................7 2.1.1. OVERALL INTRODUCTION.................................................................................................... 7 2.1.2. product size............................................................................................................................... 8 3. Parameters...................................................................................................................................................9 3.1. General parameter............................................................................................................................9 3.2. Reading parameter.........................................................................................................................10 3.3. Electric parameter...........................................................................................................................11 3.4. Working environment................................................................................................................... 11 4. Device configuration.............................................................................................................................. 12 5. Mounting method...................................................................................................................................15 6. Attention.................................................................................................................................................... 16 7. Contact info.............................................................................................................................................. 17 4 1. Preface Thank you for using the Q340 scanning equipment provided by Vguang. Reading this document carefully can help you understand the functions and features of this device, and quickly master the use and installation of the device. 1.1. Product introduction The Q340 QR code reader was a specially designed embedded type device, which has various output interface, including USB, RS232, RS485, TTL, Wiegand, suitable for vending machines, turnstiles. 1.2. Product feature 1. Scan code& swipe card all in one. 2. Fast recognition speed, high accuracy, 0.1 second the fastest. 3. Easy to operate, humanized configuration tool, more convenient to config the reader. 4. Protection level IP67. 5 1.3. FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. - - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 6 2. Product appearance 2.1.1. OVERALL INTRODUCTION Indication light Power light Reading area Fill light 7 2.1.2. PRODUCT SIZE Unit: mm 8 3. Parameters 3.1. General parameter Output interface Indicating method Imaging sensor Max resolution Mounting method Size Reading window size Certification General parameter USBRS232RS485TTLwiegand Red, green light indicator Beeper 300,000 pixel CMOS sensor 640*480 embedded mounting 75mm*65mm*28.35mm 56mm*51mm ECFCC 9 3.2. Reading parameter QR code recognition parameter Symbologies QRPDF417CODE39CODE93CODE128ISBN10ITFEAN13 DATABARaztec, etc Supported decoding Both Mobile QR code and printed QR code DOF 0mm~62.4mm(QRCODE 15mil) Reading accuracy 8mil Reading speed Reading direction 100ms per time(average), support reading continuously tilt±56.3° rotation±360° deflection±55.7° 15milQR FOV Horizontal Field 72.1° Vertical field 56.6° filed angle 84.3° 15milQR RFID reading parameter Supported cards ISO 14443A, ISO 14443B protocol cards Reading method Read UID Working frequency 13.56MHz Distance 5cm 10 3.3. Electric parameter The power input can be provided only when the device is connected properly. If the device is plugged or unplugged while the cable is live (hot plugging), its electronic components will be damaged. Make sure that the power is turned off when plugging and unplugging the cable. Poor power supply, too short interval power off and on operation may cause the device cannot work in a stable and normal status. It is necessary to keep the power input stable. After turning off the power input, it need to takes more than 2 seconds to turn on the power input again. Electric parameter Working voltage DC 5V-24V Working current 200mA5V typical value Power consumption 1000mW5V typical value 3.4. Working environment ESD protection Working temp Storge temp RH Ambient light Work environment parameter ±8kVAir discharge±4kVcontact discharge -20°C-65°C -40°C-80°C 5%-95%No condensationenvironment temperature 0-100000Lux( Non direct sunlight ) 11 4. Device configuration Use the Vguang config tool to configure the device. 5.1 config tool Config the device as the step shows, the example are showing 485 version reader. Step 1, select the model number Q300 12 Step 2, select the output interface, and config the corresponding serial parameters. Step 3, config as your needs 13 Step 4, after config as your needs, click "config code" Step 5, use the scanner to scan the configurations QR code generated by the tool, then restart the reader to finish the new configurations For more details about configurations, please refer to the "Vguang configuration tool user manual". 14 5. Mounting method The product using CMOS image sensor, the recognition window should avoid direct sun or other strong light source when install the scanner. The strong light source will cause the contrast in the image too big to decoding, the long term exposure will damage the sensor and cause the device failure. The recognition window are using tempered glass, which has good transmission of the light, and also a good pressure resistance, but still need to avoid scratching the glass by some hard object, it will affect the QR code recognition performance. The RFID antenna was in the underside of the recognition window, there should have no metal or magnetic material within 10cm when installing the scanner, or it will affect the card reading performance Step 1: open a hole in the Step 2: assemble the Step 3: assemble the Step 4, installation finished mounting plate reader with the holder, and holder with the mounting tighten the screws. plate, then tighten the Screw specification: M2*5 screws self-tapping screw 15 6. Attention 1. The equipment standard is 5-24V power supply, it can get power from the access control power or power it separately. Excessive voltage may cause the device fail to work normally or even damage the device. 2. Do not disassemble the scanner without permission, otherwise the device may be damaged. 3. The installation position of the scanner should avoid direct sunlight. Otherwise, the scanning effect may be affected. The panel of the scanner must be clean, otherwise it may affect the normal image capture of the scanner. The metal around the scanner may interfere with the RFID magnetic field and affect card reading. 4. The wiring connection of the scanner must be firm. In addition, ensure the insulation between the lines to prevent the equipment from being damaged by a short circuit. 16 7.Contact info Company name: Beijing Vguang Internet Technology Co., Ltd, Address: China Meteorological Science and Technology Park, No.2, Zhenxing Road, Changping District, Beijing, China Hot line: 400-810-2019/ +86 18914995180 17WPS 文字