Instruction Manual for myFirstech models including: FTI-CDP1-CH12, DL-CH12, DL-CH12 Cherokee TIP Start, DL-CH12, Cherokee TIP Start, TIP Start, Start
FTI-CDP1 | MyFirstech Install
FTI-CDP1: Notas de preparación y cobertura del vehículo Make DL-CH12 Jeep Model Cherokee TIP Start Year 2014-18 Install Type 5 CAN Lights Park / Auto OBD-II Type B2 IGN PINK RAP I/O Changes Green White/Blue NO N/A FIRMWARE: Esta instalación requiere el firmware BLADE-AL (DL) -CH12, el módulo flash y la actualización del firmware del controlador antes de la instalación. INSTALACIÓN Los vehículos de tipo 5 utilizan conexiones CAN en el arnés en el conector OBD-II, no se requiere el cable de extensión CAN incluido. ENCENDIDO: El encendido de tipo 5 está disponible en el conector del paquete de remolque (negro, conector de 13 clavijas, clavija # 8, rosa), ubicado a la izquierda del columna de dirección. FTI-CDP1 - Notas de instalación y configuración A CONEXIÓN REQUERIDA (OBD-II CAN) B NO SE REQUIERE (extensión CAN) C SIN CONEXIÓN D CONEXIÓN REQUERIDA (IGN) ZIIIOIIIOIIIILIIIAIINIIIIDIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII 2001 DEREK Est. IIIIIIIII R KIDS foRrEAD GOOD TECAN'T CEN AND WHO HO W WANNA LEARN TO IIIIIIIII COBFEERATTUURRAE DCEOVFEURNACGIOENES CM7000/7200 Cut loop for A/T CM7X00 CM-900S/900AS CM900AS/900S Jumper IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) SECURE TAKEOVER DOOR STATUS TRUNK STATUS HOOD STATUS E-BRAKE STATUS TACH OUTPUT BRAKE STATUS GLOW PLUG STATUS PARKING LIGHTS HAZARD LIGHTS A/M CONTROL CM-900 FTI-CDP1 - DL-CH12 - Type 5 2014-18 Jeep Cherokee TIP Start BLADE PWR pink/black C B *Not required green pink B 3 2 4 1 OBD-II connector 1 1 16 TIP Start Cylinder A TART ACC RUN S 2 Headlight switch 3 AUTO RAP SHUTDOWN OF F *Not required D Trailer Pack Connector (left of steering column) 4 7 23456 1 13 12 11 10 9 8 pink Códigos de error de programación de LED El LED del módulo parpadea en ROJO durante la programación 1x - Error de CAN 2x - Código clave no aprendido 3x - Sin ENCENDIDO 4x - Sin inmovilizador, comprobar CAN / llave 5x - Error de VIN, verifique el cableado CAN 6x - Ver error 4x 7x - Error de KLON 8x - Sin ENCENDIDO, verifique la conexión INSTALL GUIDE ALL IN ONE CHRYSLER/FIAT/JEEP Page 39 of 43 Patent No. US 8,856,780 CA 2759622 COM-BLADE-AL(DL)-CH12-EN Doc. No.: ##72849## 20201120 MODULE PROGRAMMING PROCEDURE - TIP-START NOTE I IMPORTANT: The hood must be closed. 11 Turn key to ON position. ON 1 Close driver door. Re-open driver door to wake up 12 Wait, LED will flash BLUE rapidly. data bus. 2 Press UNLOCK on OEM remote. 13 OFF Turn key to OFF position. 3 4 5 6 7 8 9 10 Wait, LED will flash BLUE once [1x]. If LED does not flash BLUE, repeat step 2. Insert key into ignition. Wait, LED will flash BLUE twice [2x]. ON OFF Turn key to ON position. Wait, LED will turn solid RED. If LED flashes BLUE rapidly, proceed to step 13. Turn key to OFF position. Remove key. Repeat steps 4 to 9, eight times [8x]. 14 15 WARNING: Disconnect power last. Disconnect module from vehicle. Connect module to computer and proceed with extended programming. 16 WARNING: Do not press module programming button. Connect power first. Connect module to vehicle. 17 18 19 Turn key to ON position. ON Wait, LED will turn solid BLUE for 2 seconds. OFF Turn key to OFF position. 20 Module Programming Procedure completed. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020 INSTALL GUIDE ALL IN ONE CHRYSLER/FIAT/JEEP Page 42 of 43 Patent No. US 8,856,780 CA 2759622 COM-BLADE-AL(DL)-CH12-EN Doc. No.: ##72849## 20201120 WARNING: READ BEFORE RNEOMTOICTEE STARTING THE VEHICLE IMPORTANT I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - TIP-START - TO THE VEHICLE OWNER NOTE 2 I All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTI N COMING UP ! 1 Press UNLOCK on after-market remote. 3 TIME RESTRICTI N Within 45 SECONDSfrom previous step: Open vehicle door. Enter vehicle. Close vehicle door. Insert key into ignition. Turn key to ON position. Press and release BRAKE pedal. Take over procedure completed. ! Failure to follow procedure within time restriction will result in vehicle engine shutdown. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020Adobe PDF library 17.00 Adobe Illustrator(R) 24.0