User Manual for speco technologies models including: VLB9, VLB7, VLT9, VLB9 2MP Outdoor HD TVI Bullet Camera, 2MP Outdoor HD TVI Bullet Camera, Outdoor HD TVI Bullet Camera, HD TVI Bullet Camera, Bullet Camera, Camera
Speco VLB9 2 Megapixel Full HD Surveilla VLB9 Tech-America
VLB9/VLB7/VLT9 User Manual Thank you for purchasing our product. Speco Technologies is constantly developing and improving products. We reserve the right to modify product design and specifications without notice and without incurring any obligation. Warnings If the product does not work properly, please contact the dealer or where the product was purchased. Speco Technologies is not responsible for any problems caused by improper operation or repair. Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity during transportation, storage, and/or installation. Do not install near sources of heat. Only install the product in environments inside the specification operating temperature and humidity range. Do not install the camera near power lines, radar equipment or other electromagnetic radiation. Do not block any ventilation openings if any. Use all the weatherproofing hardware requirement to minimize weather intrusion. Introduction This camera series is the latest technology and advanced circuit design, which features high definition and sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable, ensuring the requirement of the HD monitoring in the traditional surveillance system. High Resolution Adopt high performance sensor, providing high definition and clear image. High Transmission Performance Real-time transmission with high speed and long distance. DNR Reduce noise from brightness and color signal. OSD Access the camera settings which can be clearly displayed through the main menu. White Balance Adjust the color temperature according to the environment automatically. AGC Adjust the gain of amplifier, enabling the camera to output the standard video signal in different lighting condition. Backlight Compensation (BLC) When the back of the captured object is too much bright, you can set BLC for the captured object to make it clearer. 1 Cables Video Output Video Switch Cable Power Cable Video Switch: Four video output modes can be optional--AHD, TVI, CVI and CVBS (a) remove the cover of the video switch cable; (b) hold and press the button in the video switch cable for 5 seconds to switch the current video output. Installation Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera. Please install and use the camera in the dry environment. You'd better install back the lens cover or lower dome less than 4 hours after removing it. The mounting types of cameras are only for reference. Mounting for VLB9/VLB7 1. Drill the screw holes and the cable hole on the wall according to the drill template. 62.5mm 18.1mm 36.1mm 120° 120° 82.0 4.6 25.1 72.2 2. Route and connect the cables . 3. Secure the mounting base with camera to the wall with screws as shown below. 2 3× PA 4×25mm 3× PA 4×25mm VLB9 VLB7 4. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor and then loosen the fixed ring to adjust the view angle of the camera. Tighten the fixed ring after the adjustment. Fixed Ring Pan 360° VLB9 Tilt 80° Pan 360° Tilt 90° Fixed Ring VLB7 Mounting for VLT9 1.Drill the screw holeson the wall according to the drill template. 107mm 118.5mm 120° 120° 4.4mm 3 Loosen the fixed screw to disassemble the camera. Fixed Screw Mounting Base Enclosure Camera Unit Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided. 3× PA 4×25mm Install the camera unit and enclosure to the mounting base and then adjust if necessary to obtain an optimum view angle. Finally, fasten the camera with the fixed screw. Pan: 0°~360° Rotate: 0°~360° Tilt: 0°~75° 4 Specifications Models Specifications VLB9 VLB7 VLT9 Camera Image Sensor Resolution Image size Video Output Audio Image System Electronic Shutter IR Range (feet) Frame Rate Min. Illumination Lens Lens Mount S/N Ratio Ingress Protection Functions Function Control Day & Night WDR Digital NR AGC Auto White Balance HLC BLC Front Light Compensation Defog Smart IR Sharpness Image Setting Defect Correction Others Power Supply Power Consumption Working Environment 1/2.8" CMOS 2MP 1920×1080 AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI) NO PAL/NTSC Auto 65~98 98~164 65~98 30fps(60Hz); 25fps(50Hz) 0.005 lux @F1.2, AGC ON; 0 lux with IR 2.8 mm 2.8~12 mm 2.8 mm M12 D14 M12 52dB(AGC OFF) IP67 OSD (UTC control) ICR Digital WDR Yes Yes Yes Yes Yes No No Yes Yes Yes Auto DC12V (± 10%) IR OFF: < 1W; IR ON : < 4W IR OFF: < 1W; IR ON : < 6W -22 °F ~ 122 °F, 10 % ~ 90 %(relative humidity) IR OFF: < 1W; IR ON : < 4W Dimensions (inch) 6.74× 3.72× 3.26 8.66× 3.39× 3.38 4.67 × 3.69 5 Model: VLB9/VLB7/VLT9 Federal Communications Commission (FCC) Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Responsible Party: Speco Technologies 200 New Highway Amityville, NY 11701 www.specotech.com 6Corel PDF Engine Version 21.3.0.755