Rayprus AI Sensing Camera CSV26

About the Manual

This document, a datasheet, defines the names and functions of the parts and controls of the unit and explains how to set it up. Please read it before operating this unit. For detailed information about the AITRIOS service, see the Developer Site: https://developer.aitrios.sony-semicon.com/en/edge-ai-sensing/

Connection

Regarding PoE hubs, LAN cables, and fixed equipment, please purchase equipment that meets the following conditions separately.
PoE hub: The interface type of CSV26 is 100BASE-T RJ45, PoE. Prepare an appropriate PoE hub and LAN cable for connecting.
When using fixed equipment, prepare each equipment that meets the following requirements. Camera Fixing Equipment: The CSV26 has a tripod mounting screw hole on the bottom rear side (e), so prepare a tripod or a fixture to set up.
DEVICE INFO QR Code: Contains network connection information when using the device as a wireless LAN router.
Camera QR Code: Contains device AID-UUID information.

Specifications

Sensor Properties

Sensor Model	IMX500
Shutter Type	Rolling shutter
Sensor Size	1/2.3" (Diag. 7.857mm)
Resolution	12.33 MP, 4056 x 3040px
Pixel Size	1.55 μm

Controller Properties

Controller Module	ESP32-WROVER-E
Processor	Two low-power Xtensa® 32-bit LX6 microprocessors
RAM	520KB on-chip SRAM, 8MB PSRAM
Storage	16MB SPI flash

Physical Properties

Dimensions	55mm X 40mm X 35mm (excludes lens protrusion)
Lens Mount	S-Mount
Weight	48 g
Focal length	4.35mm
Focus Type	Fixed Focus (Focused at 2m) performance varies depending on application
Field of View (D x H x V)	85.5° x 71.6° x 56.8°
Aperture	F3.0
Distortion	Optical distortion: <-1.55% TV Distortion: <-0.62%

Interface and Power Information

Digital Interface	100BASE-T RJ45, PoE
Power Requirement	PoE (IEEE 802.3af)
Power Consumption	Typ. 1.5W Max. 3W

Standard and Certifications

Compliance	CE, IC, FCC, MIC, ETL, RoHS
Storage Temperature	-30°C to 60°C
Operating Temperature	-10°C to 40°C ambient
Humidity	Operating: 20%~80% relative, non-condensing

Location and Function of Parts

The camera body is shown from the front and side. Labeled components include: (a) Power Indicator light, (b) Reset/Mode Button, (c) Services Indicator light, (d) Ethernet RJ45 port, (e) Tripod mounting screw hole on the bottom rear, and (g) two screw holes on the back cover. The diagram also indicates holes on the corners intended for attaching a security or fall prevention wire.

Status Indicator Lights:

(a) Power Indicator
(b) Reset / Mode Button
(c) Services Indicator

Ports and Mounts:

(d) Ethernet RJ45
(e) Tripod mounting screw hole
(f) (g) Two screws hole on the back cover

Label and Positions

1. DEVICE INFO QR Code: When scanned with Device Installer, a wireless LAN connection is established between Device Installer and the Edge Device. Refer to the Device Setup Guide for details.

2. AID-UUID QR Code: This identifier is used to request the device certificate or register it to the AITRIOS service. If the Camera QR code is dirty or scratched, check the AID-UUID written on the device.

3. Carton label: The carton label contains the following information: Al Sensing Camera, Model: CSV26, Rating: 3W(MAX) via PoE, Serial Number (S/N), UUID, Manufacturer (Triple Win Precision Electronics (Jin Cheng) Co., Ltd.), and country of origin (MADE IN CHINA).

Appendix A: Mechanical Drawings

Mechanical drawings illustrate the camera's physical dimensions and mounting points. Views include a side view with the back cover attached, showing overall dimensions (approximately 55.0mm width, 21.0mm height, with back cover section depth around 12.5mm and total width including connector around 34.8mm). Other views show the back cover removed and snapped in. Key features highlighted include the Ethernet Connector port and Cable Access point. The 13mm lens is visible. Buttons are labeled as Service Indicator, Reset/Mode Button, and Power Indicator. Mounting holes are detailed, including a 1/4-20 UNC tripod screw hole and 3.5mm anti-drop wire holes. Specific dimensions for cable access (13.1mm width), mounting plate (37mm width, 45.8mm length), and hole diameters (e.g., 3.2mm, 6.5mm) are provided.