User Manual for EQUINOX models including: EQLED203 Super Boogie, EQLED203, Super Boogie, Boogie
Equinox Super Boogie
File Info : application/pdf, 12 Pages, 1.32MB
DocumentDocumentSuper Boogie User Manual Order code: EQLED203 Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! · Before your initial start-up, please make sure that there is no damage caused during transportation. · Should there be any damage, consult your dealer and do not use the equipment. · To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual. · Please note that damages caused by user modifications to this equipment are not subject to warranty. CAUTION! KEEP THIS EQUIPMENT AWAY FROM RAIN, MOISTURE AND LIQUIDS CAUTION! TAKE CARE USING THIS EQUIPMENT! HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!! IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment. · Never let the power cable come into contact with other cables. Handle the power cable and all mains voltage connections with particular caution! · Never remove warning or informative labels from the unit. · Do not open the equipment and do not modify the unit. · Do not connect this equipment to a dimmer pack. · Do not switch the equipment on and off in short intervals, as this will reduce the system's life. · Only use the equipment indoors. · If the equipment has been exposed to drastic temperature fluctuation (e.g. after transportation), do not connect power or switch it on immediately. The arising condensation might damage the equipment. Leave the equipment switched off until it has reached room temperature. · If your product fails to function correctly, stop use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Pro Light dealer for service. · Do not sit the equipment on a flat surface as this can block the air intake to cool the LED. · Do not expose to flammable sources, liquids or gases. · Always disconnect the power from the mains when equipment is not in use or before cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the power-cable. · Make sure that the available mains supply voltage is between 100~240V AC, 50/60Hz. · Make sure that the power cable is never crimped or damaged. Check the equipment and the power cable periodically. · If the equipment is dropped or damaged, disconnect the mains power supply immediately and have a qualified engineer inspect the equipment before operating again. · Only use fuses of same type and rating. · Repairs, servicing and power connection must only be carried out by a qualified technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS. · This lighting fixture is for professional use only - it is not designed for or suitable for household use. The product must be installed by a qualified technician in accordance with local territory regulations. The safety of the installation is the responsibility of the installer. The fixture presents risks of severe injury or death due to fire hazards, electric shock and falls. · Warning! Risk Group 2 LED product according to EN 62471. Do not view the light output with optical instruments or any device that may concentrate the beam. · WARRANTY: One year from date of purchase. OPERATING DETERMINATIONS · If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc. · Do not endanger your own safety and the safety of others! Incorrect installation or use can cause serious damage to people and/or property. www.prolight.co.uk Super Boogie User Manual 2 Product overview & technical specifications Super Boogie The extremely wide coverage effect with super bright LEDs makes the Super Boogie ideal for both installation and mobile applications. Brilliant beams of colour along with versatile light shows make this effect impressive under both DMX and built-in show modes. · 24 x 3W LEDs (R: 6, G: 6, B: 6, A: 6) · Beam angle: 78° · DMX channels: 4/6 or 26 selectable · Auto, sound active and master/slave modes · 0-100% dimming and variable strobe · IR remote control included · Supplied with mounting bracket · 4 push button menu with LED display · IEC power input/output · 3-Pin XLR input/output · Convection cooled Specifications Power consumption Power supply Fuse Dimensions Weight Order code 72W 100~240V, 50/60Hz F3A 250V 277 x 265 x 240mm 2.9kg EQLED203 265mm 240mm 203mm 40mm 277mm 70mm www.prolight.co.uk Super Boogie User Manual 3 Technical specifications 01 02 www.prolight.co.uk POWER INPUT: 100-240V~50/60Hz FUSE: F3A 250V POWER CONSUMPTION: 72W 06 DMX INPUT SAFETY ETE 03 07 04 MIC 08 05 POWER OUTPUT: 100-240V~50/60Hz MENU UP DOWN ENTER DMX OUTPUT 01 - Hanging bracket 02 - Adjustment knobs 03 - IEC power input 04 - Fuse F3A 250V 05 - IEC power output 06 - Safety eye www.prolight.co.uk 11 10 09 07 - 3-Pin DMX input 08 - 3-Pin DMX output 09 - LED display 10 - Function buttons 11 - Microphone In the box: 1 x fixture, 1 x power cable & 1 IR remote Super Boogie User Manual 4 Operating instructions Addr A001 DMX address setting A512 MENU CHnd SLnd SoUn AutO LEd d1sp d1sp 4Ch 6 C h Channel modes 26Ch NASt S L 1 Master/ slave mode SL2 5 o 0 5 o 1 7 Sound active 5 e 0 0 5 e 9 9 Sound sensitivity A u 1 A u 1 7 Auto modes S P 1 S p 9 Auto speed oN Display blackout oFF Display invert t e s t Auto Test v e r v 1 0 Firmware Version www.prolight.co.uk Super Boogie User Manual 5 Operating instructions DMX mode: Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show. In this mode you will be able to control each individual trait of the fixture and each fixture independently. To access the DMX address mode, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show Addr on the LED display. Now press the "ENTER" button and use the "UP" and "DOWN" buttons to set the required DMX address. Press the "ENTER" button to confirm the setting. To exit out of any of the above options, press the "MENU" button. DMX channel mode: To access the DMX channel mode, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show Chnd on the LED display. Now press the "ENTER" button and use the "UP" and "DOWN" buttons to choose one of the 4, 6 or 26 DMX channel modes. Press the "ENTER" button to confirm the setting. To exit out of any of the above options, press the "MENU" button. 4 channel mode: Channel Value CH1 000-255 000-008 CH2 009-255 000-007 008-022 023-037 038-052 053-067 068-082 083-097 098-112 113-127 CH3 128-142 143-157 158-172 173-187 188-202 203-217 218-232 233-247 248-255 000-127 CH4 128-255 Function Master dimmer (0-100%) No function Strobe (slow-fast) No function Chase 01 Chase 02 Chase 03 Chase 04 Chase 05 Chase 06 Chase 07 Colour Chase Chase 08 Chase 09 Chase 10 Chase 11 Chase 12 Chase 13 Chase 14 Chase 15 Chase 16 All Chase Chase Auto Speed (slow-fast) Chase Sound Sensitivity (low-high) www.prolight.co.uk Super Boogie User Manual 6 6 channel mode: Channel Value CH1 000-255 CH2 000-255 CH3 000-255 CH4 000-255 CH5 000-255 000-007 CH6 008-255 26 channel mode: Channel Value CH1 000-255 000-007 CH2 008-255 CH3 000-255 CH4 000-255 CH5 000-255 CH6 000-255 CH7 000-255 CH8 000-255 CH9 000-255 CH10 000-255 CH11 000-255 CH12 000-255 CH13 000-255 CH14 000-255 CH15 000-255 CH16 000-255 CH17 000-255 CH18 000-255 CH19 000-255 CH20 000-255 CH21 000-255 CH22 000-255 CH23 000-255 CH24 000-255 CH25 000-255 CH26 000-255 Function Red dimmer (0-100%) Green dimmer (0-100%) Blue dimmer (0-100%) Amber dimmer (0-100%) Master dimmer (0-100%) No function Strobe (slow-fast) Function Master dimmer (0-100%) No function Strobe (slow-fast) Red 1 dimmer (0-100%) Green 1 dimmer (0-100%) Blue 1 dimmer (0-100%) Amber 1 dimmer (0-100%) Red 2 dimmer (0-100%) Green 2 dimmer (0-100%) Blue 2 dimmer (0-100%) Amber 2 dimmer (0-100%) Red 3 dimmer (0-100%) Green 3 dimmer (0-100%) Blue 3 dimmer (0-100%) Amber 3 dimmer (0-100%) Red 4 dimmer (0-100%) Green 4 dimmer (0-100%) Blue 4 dimmer (0-100%) Amber 4 dimmer (0-100%) Red 5 dimmer (0-100%) Green 5 dimmer (0-100%) Blue 5 dimmer (0-100%) Amber 5 dimmer (0-100%) Red 6 dimmer (0-100%) Green 6 dimmer (0-100%) Blue 6 dimmer (0-100%) Amber 6 dimmer (0-100%) Operating instructions www.prolight.co.uk Super Boogie User Manual 7 Operating instructions Master/slave mode: To set the master unit, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show SLnd on the LED display. Press the "ENTER" button and use the "UP" and "DOWN" buttons on the rear of the unit to show NASt. Press the "ENTER" button to confirm the setting. To set the other units in slave mode, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show SLnd on the LED display. Now press the "ENTER" button and use the "UP" and "DOWN" buttons to choose either SL1 or SL 2. Press the "ENTER" button to confirm the setting. The unit/s will now run in sequence with the master unit. To exit out of any of the above options, press the "MENU" button. Please ensure that all slave units are set to the same DMX channel mode as the master unit. Sound active: To access the sound active setting, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show SoUn on the LED display. Now press the "ENTER" button and use the "UP" and "DOWN" buttons to choose between So 0 to So17. Press the "ENTER" button and use the "UP" and "DOWN" buttons to select the sound sensitivity between Se0O to Se99. Press the "ENTER" button to confirm the setting. Value: 0 - 99 (0 = low, 99 = high) To exit out of any of the above options, press the "MENU" button. Auto Modes: To access the auto setting, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show Aut0 on the LED display. Now press the "ENTER" button and use the "UP" and "DOWN"" buttons to choose between Au 1 to au17. Press the "ENTER" button and use the "UP" and "DOWN"" buttons to select the auto speed between SP 1 to SP 9. Press the "ENTER" button to confirm the setting. To exit out of any of the above options, press the "MENU" button. Display blackout: To access the display blackout setting, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show LEd on the LED display. Now press the "ENTER" button and use the "UP" and "DOWN" buttons to choose between on (display blacks out) or ofF (display always on). Press the "ENTER" button to confirm the setting. To exit out of any of the above options, press the "MENU" button. www.prolight.co.uk Super Boogie User Manual 8 Operating instructions Display invert setting: To access the display invert setting, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show dIsp on the LED display. Now press the "ENTER" button and use the "UP" and "DOWN" buttons to choose between dIsp or ds1p. Press the "ENTER" button to confirm the setting. To exit out of any of the above options, press the "MENU" button. Software version: To access the fixtures software version, press the "MENU" button and use the "UP" and "DOWN" buttons on the rear of the unit to show uer on the LED display. Now press the "ENTER" button. The unit will now display the fixtures software version e.g. u10. To exit out of any of the above options, press the "MENU" button. IR remote functions: Button functions: 01 01 - Sets the unit into blackout on or off 02 - Runs the auto mode use the PRO LIGHT `+' and `-` buttons to change the desired program and use the SPEED/SEN button to change the program speed 03 - Runs the relevant sound mode use the SPEED/SEN button to change the sensitivity ON/OFF AUTO 02 04 - Runs the strobe mode use the SPEED/STROBE `+' and `-` 03 buttons to change the strobe speed 05 - Adjusts the auto program use the `+' and `-` buttons to select the desired program MUSIC MUSIC MUSIC 1 2 3 06 - Adjusts the auto speed/sound sensitivity use the `+' 04 and `-` buttons to select the desired speed/sensitivity level STROBE 07 - Adjusts the strobe speed use the `+' and `-` buttons to select the desired strobe speed 05 PRO LIGHT + + + 06 SPEED/ SEN 07 SPEED/ STROBE www.prolight.co.uk Super Boogie User Manual 9 DMX setup Setting the DMX address: The DMX mode enables the use of a universal DMX controller. Each fixture requires a "start address" from 1- 512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, 105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the chain starts at 107. DMX 512: DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA "IN" and DATA "OUT" XLR terminals located on all DMX fixtures (most controllers only have a data "out" terminal). DMX linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. DATA cable (DMX cable) requirements (for DMX operation): This fixture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit. Your unit requires either a standard 3-pin or 5-pin XLR connector for data input/output, see images below. Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight Concepts dealers. Please quote: 3-Pin: CABL10 2m CABL11 5m CABL12 10m 5-Pin: CABL185 2m CABL187 5m CABL188 10m Also remember that DMX cable must be daisy chained and cannot be split. www.prolight.co.uk Super Boogie User Manual 10 DMX setup Notice: Be sure to follow the diagrams below when making your own cables. Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing. Grounding the shield could cause a short circuit and erratic behaviour. Pin Configuration 3-Pin 5-Pin Pin 1 - Ground Pin 2 - Negative Pin 3 - Positive Pin 4 - N/C Pin 5 - N/C DMX 512 3-Pin XLR output 1 3 2 GROUND DMX + DMX DMX 512 3-Pin XLR input 1 3 2 3-Pin XLR male 3-Pin XLR female 1 ground 3 hot 2 cold 2 cold 1 ground 3 hot DMX 512 5-Pin XLR output DMX 512 5-Pin XLR input GROUND 12 DMX 21 3 DMX + 3 54 N/C 45 N/C 5-Pin XLR male 5-Pin XLR female 1 ground 2 cold 3 hot 5 N/C 4 N/C 5 N/C 4 N/C 3 hot 1 ground 2 cold Line termination: When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behaviour. Using a cable terminator will decrease the possibilities of erratic behaviour. (3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89) 3-Pin 12 3 Termination reduces signal transmission problems and interference. It is always advisable to connect a DMX terminal, (resistance 120 Ohm 1/4W) between pin 2 (DMX-) and pin 3 (DMX+) of the last fixture. 5-Pin 15 24 3 5-pin XLR DMX connectors: Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion. 5-pin XLR (female) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) Pin 4: N/C Pin 5: N/C 3-pin XLR (male) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) 3-pin XLR (female) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) 5-pin XLR (male) Pin 1: GND (screen) Pin 2: Signal (-) Pin 3: Signal (+) Pin 4: N/C Pin 5: N/C www.prolight.co.uk Super Boogie User Manual 11 Multiple fixture power linking / WEEE notice Power linking: This fixture provides power linking via the power output on the rear allowing multiple units to be connected together. The maximum number of fixtures that can be connected is 20 fixtures @ 240V or 10 fixtures @ 120V (including the first fixture). After the maximum number of fixtures are connected a new power run will need to be started. Please note: Caution should be used when power linking other fixtures to the Super Boogie as the power consumption of other fixtures will vary. Fixtures fitted with lamps often require 2/3 times more current on startup, these may require their own power source.. POWER INPUT: 100-240V~50/60Hz FUSE: F3A 250V POWER CONSUMPTION: 72W www.prolight.co.uk SAFETY ETE DMX INPUT MIC POWER OUTPUT: 100-240V~50/60Hz MENU UP DOWN ENTER DMX OUTPUT POWER INPUT: 100-240V~50/60Hz FUSE: F3A 250V POWER CONSUMPTION: 72W www.prolight.co.uk SAFETY ETE DMX INPUT MIC POWER OUTPUT: 100-240V~50/60Hz MENU UP DOWN ENTER DMX OUTPUT Correct Disposal of this Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. www.prolight.co.uk Super Boogie User Manual 12