download.schneider-electric.com/files?p_Doc_Ref=NNZ5883500
User Guide for CLIPSAL models including: Wiser Micro Module Blind, Wiser, Micro Module Blind, Module Blind, Blind
Wiser Micro Module Blind - Clipsal Portal
File Info : application/pdf, 32 Pages, 13.07MB
DocumentDocumentWiser Micro Module Blind Device user guide Information about features and functionality of the device. 05/2023 www.clipsal.com Legal Information The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners. This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of Schneider Electric. Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an "as is" basis. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel. As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice. To the extent permitted by applicable law, no responsibility or liability is assumed by Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein. Table of Contents Safety information.......................................................................................4 Wiser Micro Module Blind ..........................................................................5 For your safety ...........................................................................................5 About the device.........................................................................................6 Installing the device ....................................................................................6 Testing the device.......................................................................................6 Pairing the device .......................................................................................6 Pairing device manually.........................................................................7 Pairing device with auto scan.................................................................9 Configuring the device ..............................................................................10 Changing the device icon ....................................................................10 Renaming the device .......................................................................... 11 Changing the device location ...............................................................12 Calibration .......................................................................................... 13 Removing the device ................................................................................16 Resetting the device .................................................................................17 Using the device.......................................................................................18 Manual operation ................................................................................18 Opening/Closing the shutter using app .................................................18 Setting up a schedule..........................................................................20 Creating a moment .............................................................................21 Creating an automation .......................................................................24 LED indication ..........................................................................................29 Troubleshooting .......................................................................................29 Technical data ..........................................................................................29 Compliance .............................................................................................. 30 Compliance information for Green Premium products ............................30 Trademarks ........................................................................................30 DUG_Wiser Micro Module Blind_CLP-00 3 Safety information Safety information Important information Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of either symbol to a "Danger" or "Warning" safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. Failure to follow these instructions will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE NOTICE is used to address practices not related to physical injury. 4 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Wiser Micro Module Blind CLP5015WBZ For your safety DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Safe electrical installation must be carried out only by skilled professionals. Skilled professionals must prove profound knowledge in the following areas: · Connecting to installation networks. · Connecting several electrical devices. · Laying electric cables. · Safety standards, local wiring rules and regulations. Failure to follow these instructions will result in death or serious injury. DANGER HAZARD OF ELECTRIC SHOCK · Make sure that the terminal connection area does not come in contact with the metallic parts of any device installed in the same location. · Do not short the outputs to neutral. · The motor contacts and live conductor connection must be separated from one another by a 240 VAC basic insulation. Failure to follow these instructions will result in death or serious injury. WARNING HAZARD OF ELECTRIC SHOCK · Observe the regulations for working on live parts. · Only actuate the device buttons using insulated auxiliary equipment that meets the requirements of EN 60900. Failure to follow these instructions can result in death, serious injury, or equipment damage. DUG_Wiser Micro Module Blind_CLP-00 5 About the device Wiser Micro Module Blind The Wiser Micro Module Blind (hereinafter referred to as module) combines the advantages of smart shutter functionality with ordinary mechanical double pushbutton switches. It transforms a conventional switch into a connected device that you can control from the switch or through the Wiser app. Relay contacts are mechanically locked against each other to prevent simultaneous triggering of the two relay outputs. NOTE: Do not control any devices that depend on a permanent power supply. Additional features: · Remote control with maximum of 10 mechanical double push-button switches. · Protection of the motor against damage with two mutually mechanically and electronically locked relay contacts. · Electronic overload protection, overheating protection and short-circuit protection. · Setting a time schedule. Installing the device Refer to the installation instruction supplied with this product. See Wiser Micro Module Blind. Testing the device Before using the module, manually test the module and make sure that it works when connected to the shutter. · Short press the push button once, the shutter opens/closes gradually. · Press and hold the push button, the shutter opens/closes fully, record the time it takes to fully open/close the shutter. Pairing the device Using the Wiser app, first pair your device with the Gateway/Hub to access and control the device. You can either add the device manually or do an auto-scan to pair it. 6 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Pairing device manually To pair the device manually: 1. On Home page, tap + . 2. Tap and select the Wiser Hub 3. Select an option to add the device (A): Add Device with Install Code Add Device without Install Code Add Device Install Code is Recommended To enhance network security, we strongly recommend using the install code to add a device. If you are unable to scan or type the install code, you can still add the device without it. Add Device with Install Code A Add Device without Install Code TIP: It is recommended to add the device with install code. 4. To pair the device with an install code, tap Add Device with Install Code to display the slide-up menu. Select any one of the options (B): Scan Install Code: you can scan the device for the install code. TIP: You can find the QR code on the rear side of the device. Enter Install Code Manually: you can manually enter the install code from the device. TIP: You can find the install code on the rear side of the device. After scanning or entering the install code, proceed to Step 6. Add Device Install Code is Recommended To enhance network security, we strongly recommend using the install code to add a device. If you are unable to scan or type the install code, you can still add the device without it. Add Device with Install Code Add DevSiccaenwIintshtoaulltCInodsetall Code B Enter Install Code Manually Cancel 5. To pair the device without install code, tap Add Device without Install Code. DUG_Wiser Micro Module Blind_CLP-00 7 Wiser Micro Module Blind 6. Remove front panel from switch to access the device if you place the module behind a mechanical push button. 7. Short press the push button 3 times. The LED blinks orange. NOTE: If the module is located behind the push button, the status LED is not visible. 8. In the app, select Confirm LED is flashing orange and tap Start Configuration (C). Cancel How to pair device 1. Remove front panel from switch. 12 LN1 2 3 12 LN1 2 C 9. After a few seconds, a solid green LED indicates that the device is successfully paired to the Hub. 10. After the device is added in the app, tap Done. 8 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Pairing device with auto scan Pairing the device with auto scan automatically discovers the device when the corresponding device is powered on. To pair the device: 1. On the Home page, tap +. 2. Tap Auto scan tab and tap Confirm. 3. If you have multiple hubs, do Step 4 or proceed to Step 5. 4. Tap Select hub and select the Wiser hub from the slide-up menu. 5. Short press the setup/reset button 3 times (< 0,5 s) and wait for a few seconds until the device search is complete. The LED blinks orange. TIP: If you want to pair multiple devices at once, perform step 5 on each device and wait for a few seconds for them to be detected. 6. Tap Next (A) and select Micromodule Shutter. Auto Scan Micro Next A 7. Once the device is added successfully, tap Done. DUG_Wiser Micro Module Blind_CLP-00 9 Configuring the device Wiser Micro Module Blind Changing the device icon You can change the device icon using the Wiser app. 1. On the Home page, select the device for which you wish to change the icon. 2. At the top-right corner of the screen, tap . 3. Tap edit next to the device name. 4. Tap Icon to view the menu. 5. In the slide-up menu, select any one of the following (A) to change the device icon: Take photo - allows you to take a photo with your device camera. Select from Icon Library - allows you to select an icon from the app library. Select from Album - allows you to select a photo from the mobile gallery. Icon Name Location Take photo Select from Icon Library A Select from album Cancel 10 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Renaming the device You can rename the device using the Wiser app. 1. On the Home page, select the device for which you wish to rename. 2. At the top-right corner of the screen, tap . 3. Tap edit next to the device name. 4. Tap Name, enter the new name (A) and then tap Save. Icon Rename Name LocationCancel A Save DUG_Wiser Micro Module Blind_CLP-00 11 Wiser Micro Module Blind Changing the device location You can change the device location using the Wiser app. 1. On the Home page, select the device for which you wish to change the location. 2. At the top-right corner of the screen, tap . 3. Tap edit next to the device name. 4. Tap Location. 5. Select the desired location from the list (A) and then tap Save. Device location Save Living Room Master Bedroom Kitchen A Dining Room Study Room Kids Room 12 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Calibration The shutter control is supplied in an uncalibrated state. Each shutter motors vary in the speed at which they open and close (edge to edge). Therefore, the opening/ closing time of the shutter must be determined in the app. NOTE: · Before using this device for the first time, it must be calibrated, or you can adjust its duration manually. · Do not use the shutter either manually or on the app during calibration to avoid interruption. Shutter calibrating To calibrate the run time manually: 1. On the device control panel page, tap Settings > Open/Close Duration. 2. On the slide-up menu, you can set the run time manually using +/- button or using the sliding bar (A) and then tap Confirm. NOTE: To determine the default run time, record the time it takes to fully open/close the shutter (edge to edge). Settings 6 Sec 90 Slat Rotation B 120 Sec 0 Sec 45 Sec 90 Sec A 180 Sec Cancel To calibrate the run time using app: 1. In Settings > Open/Close Duration, tap Calibration (B). DUG_Wiser Micro Module Blind_CLP-00 13 Wiser Micro Module Blind 2. On the slide-up menu, select the calibration start point (C): Start From The Top: shutter will move from top to bottom (closing). Start From the Bottom: shutter will move from bottom to top (opening). Settings 6 Sec 90 Slat Rotation 5 Sec Start from the top C Cancel 3. Wait until the shutter reaches its starting point and then tap Start. 4. Tap Done (D) once the shutter reaches other end. Settings 6 Sec 90 Slat Rotation 5 Sec Done 00:10 Cancel Done D The app displays the progress of calibration. 5. Once the process is complete, tap Tilt Calibration on the pop-up window for shutter slat calibration. 14 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Slat tilt angle calibration To calibrate slat tilt angle: 1. On the setting page, tap Slat Tilt Angle for slide-up menu. 2. Select tilt type (A) based on the motor installed and then tap Confirm 90 Slat Rotation 180 Slat Rotation Not Supported Blind Settings 6 Sec of motor. 90 Slat Rotation 5 Sec 0~90° Tilt 0~180° 90 Slat Rotation A 180 Slat Rotation Cancel IMPORTANT: If the shutter is installed with a non rotating slat or blind, the calibration process is complete, and no further steps to follow. 3. Read the pop-up notification and tap Confirm. 4. Make sure the shutter is in fully closed state and tap Prepare. 5. Select the check box (B) and tap Start. Settings 6 Sec 90 Slat Rotation 5 Sec B to 90 00.00 Start D Cancel C Reset 5 Sec Done 6. Tap Stop (C) to finish calibration. TIP: You can retake the calibration by tapping Reset. 7. Tap Done once the process is complete. The app displays the progress of calibration. TIP: You can set the run time manually by taping Duration Adjustment (D). DUG_Wiser Micro Module Blind_CLP-00 15 Removing the device Wiser Micro Module Blind Using the Wiser app, you can remove a device from the device list. To remove the device: 1. On the Home page, tap All devices > Micromodule Shutter. 2. Tap to display more details. 3. Tap Remove and Factory Reset Device (A). More Micro Module Shutter Others A TIP: On the Home page, tap and hold the Micromodule Shutter to remove the device. NOTE: · Removing the device will reset the module. After reset the LED turns orange indicating that the module is ready to pair with another network. · If there is a problem while pairing or resetting the module, refer to Resetting the device, page 17. 16 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Resetting the device You can reset the device to factory default manually. Short press the push button 3 times and then long press the push button once for 10 s. After 10 s, LED starts blinking red then release the operation button. NOTE: All configuration data, user data, and network data are deleted. After which · No connectivity to other devices or rooms · No timer settings The LED stops blinking upon successful reset of the device. The module restarts and blinks green for a few seconds. NOTE: After reset, the LED turns orange indicating that the device is ready for pairing. DUG_Wiser Micro Module Blind_CLP-00 17 Using the device Wiser Micro Module Blind Manual operation When the module is connected to a mechanical double push-button switch, the shutter can be controlled manually. · Short press the push button once, the shutter opens/closes gradually. · Press and hold the push button, the shutter opens/closes fully. Opening/Closing the shutter using app Using the Wiser app shutter can be controlled by following method. Opening/Closing through home page To open/close the shutter: 1. On the Home page, Tap All devices. 2. In Micromodule Shutter Tap on . 3. On the slide up Control menu select Open/Close to operate the shutter. My Home Welcome Home Home Away All Devices · · · Open Close Control Home Opening/Closing through device menu The shutter can be open/close to the desire percentage. To open/close the shutter: 18 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind 1. On the Home page, Tap All devices > Micromodule Shutter. 2. On the device menu, drag the sliding bar (A) up/down to set the desired shutter opening/closing percentage. 3. Tap on Open/Mid-Open/Close (B) position to tilt the Slat (Only if the shutter is installed with rotation slat). Micro Module Shutter A B Open Mid-Open Close DUG_Wiser Micro Module Blind_CLP-00 19 Wiser Micro Module Blind Setting up a schedule The devices can be fully controlled by schedule. Once the schedule is set, the devices operate at a given time. To create a schedule: 1. On the Home page, Tap All devices > Micromodule Shutter. 2. Tap Schedule > Add Schedule to add a schedule. 3. In Add Schedule menu, set the time (A). 4. Tap Repeat (B) to select the days you want to set the schedule. 5. Tap Note (C), enter the note and tap Confirm. 6. Tap the toggle switch (D) to turn on the Notification for the schedule. The app will send a notification that the scheduled task is executed at the time of schedule. 7. Tap Control (E) and select any one option, Shutter Open / Shutter Close. Cancel Add Schedule 06 07 08 18 19 20 09 21 10 22 AM 12 24 13 25 12 26 27 Save A B Repeat C Note Once D E 0% Close 0% 100% Open 8. Tap Save 20 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Creating a moment A Moment allows you to group multiple actions that are usually done together. Using the Wiser app, you can create moments based on your needs. To create a moment: 1. On the Home page, tap . 2. Go to Moment > + to create a moment. 3. Tap Edit name (A), enter the name of the moment and tap Save. TIP: You can choose the cover image that best represents your moment by tapping . Cancel Moment settings Save Edit name Action A Edit name Add Task (0/10) Cancel Save 4. In the Action section, tap Add task (B) to open the slide-up menu. 5. In the Add task menu, you can do either or all of the following actions (C): Run the device: select the devices that you want in a moment. Select Automation: select the automation that you want to enable or disable. Delay: set the delay time. NOTE: You can add one or more actions using . Cancel Moment settings Save Edit name Action (0/10) Add Task B Add Task Run the device Select Automation C Delay DUG_Wiser Micro Module Blind_CLP-00 21 Wiser Micro Module Blind 6. Tap Run the device > Micromodule Shutter and select either or all the functions to add in the moment: Control > Shutter Open / Shutter Close (D) Percentage > Set the percentage (E) of moment required. Select function Next D Control E Close 50% 7. Set all the actions and tap Save. Cancel Moment settings Save Micromodule Shutter Moment Action Show on Home Page 22 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Editing a moment 1. On the Moment tab, locate the moment you want to edit and tap . 2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings. TIP: · You can add one or more actions using . · To delete an existing action, slide each item towards left and tap Delete. Deleting a moment To delete a moment: 1. On the Moment tab, locate the moment that you want to delete and then tap . 2. Tap Delete and then tap Ok. NOTE: After deleting a moment, the device action can no longer be triggered. DUG_Wiser Micro Module Blind_CLP-00 23 Wiser Micro Module Blind Creating an automation An automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. By using the Wiser app, you can create automations based on your needs. To create an automation: 1. On the Home page, tap the . 2. Go to Automation > + to create an automation. 3. Tap Edit name (A), enter the name of the automation and tap Save. TIP: You can choose the cover image that best represents your automation by tapping . Cancel Automation settings Save My Automation Any condition is met Edit name (0/10) Add Condition A Action Cancel (ASdadvede 0/80) Add Task All-Day 4. Tap Any condition is met to select any one of the condition type (B): All conditions are met: the automation is triggered when all the conditions are met. Any condition is met: the automation is triggered when at least one condition is met. Cancel Automation settings Save My Automation Any condition is met (0/10) Add Condition Action (Added 0/80) Add Task Select Condition type All conditions are met B Any condition is met Cancel 5. Tap Add Condition to open the slide-up menu. 24 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind 6. In the Add Condition menu, you can do either or all of the following options (C): When weather changes : select the various weather settings. Schedule: set the time and day. When device status changes: select the device and it's function. NOTE: You can add one or more conditions using . Cancel Automation settings Save My Automation Any condition is met (0/10) Add Condition Add Condition When weather changes Schedule C When device status changes 7. Tap When device status changes > Micromodule Shutter > Percentage and update the percentage of closing and opening of shutter. Percentage Next 0% Close 0% 100% Open 8. Tap Add task to open the slide-up menu. DUG_Wiser Micro Module Blind_CLP-00 25 Wiser Micro Module Blind 9. In the Add task menu, you can do either or all of the following options (D): Run the device: select the devices that you want to be triggered. Enable or disable Automation: select the automation that you want to enable or disable. Send notification: turn on notification for the automation. Delay: set the delay time. NOTE: You can add one or more actions using . Cancel Automation settings Save My Automation Any condition is met (0/10) Add Condition Action (Added 0/80) Add task Run the deAvdidceTask Moment or Automation D All-Day Delay 10. Tap on Effective period to set the time range for the automation. You can select any one of the following (E): All-day - 24 hours Daytime - From sunrise to sunset Night - From sunset to sunrise Custom - User defined time period Next All-day 24 hours Daytime From sunrise to sunset Night From sunset to sunrise E Custom Repeat City Everyday 11. Set all the actions and conditions and tap Save. Automation is now available under Automation tab. Use toggle switch to enable/disable automation. 26 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind Example of an automation This demonstration shows you how to create an automation to open the Micromodule Shutter at the scheduled time. 1. Go to Automation > + to create an automation. 2. Tap Edit name, enter the name of the automation and tap Save. TIP: You can choose the cover image that best represents your automation by tapping . 3. Tap Add Condition > Schedule. · Tap Repeat (A), select the days you want to set the schedule and tap Save. · Set the time (B) at which the automation must start and tap Next. Schedule Next A Repeat Execution Time 17 59 B 18 00 19 01 Everyday AM PM Note - Schedule is based on family location time zone. 4. Tap Add task > Run the device > Micromodule Shutter. 5. Tap Control > Shutter Open (C) and tap Save. 6. Tap Percentage (D) to update the percentage of shutter opening and tap Save. Select function Next C Control D Close 100% 7. Tap Next. DUG_Wiser Micro Module Blind_CLP-00 27 8. In the Automation Settings page, tap Save. Cancel Automation Settings Save My Automation Wiser Micro Module Blind Any condition is met Action Control: Open All-Day Automation is now available under Automation tab. Use toggle switch to enable/disable automation. Editing an automation 1. On the Automation tab, locate the automation you want to edit and tap . 2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings. TIP: · You can add one or more condition or actions using . · To delete an existing condition or action, slide each item towards left and tap Delete. Deleting an automation 1. On the Automation tab, locate the automation that you want to delete and then tap . 2. Tap Delete and then tap Ok. NOTE: After deleting an automation, the device action can no longer be triggered. 28 DUG_Wiser Micro Module Blind_CLP-00 Wiser Micro Module Blind LED indication Pairing the device User Action Short press the push button 3 times. LED Indication LED blinks orange once per second. Status Pairing mode is active for 30 seconds. When pairing is completed, LED glows green for a few seconds before turning off. Resetting the device User Action Short press the push button 3 times and hold it down once for > 10 s. LED Indication LED blinks red once per second. Status The device is in reset mode. The device then restarts and LED turns orange indicating that the device is ready for pairing. Troubleshooting Symptom No shutter movement or uncontrolled shutter movement. The device is not ready to pair after the device is removed from the app. Solution · Check power supply. · Check the wiring between module and push-button switch.. · Check the load Reset to factory default settings, refer to Resetting the device, page 17 Technical data Nominal voltage Nominal current Blind channel Standby Operating Temperature Neutral conductor Connecting terminals Extension connection Length of all cable sections Fuse protection Operating frequency Max. radio-frequency power transmitted IP rating Product dimensions (H x W x D) Communication protocol AC 220-240 V, 50/60 Hz 4 A, cos = 0.6 - 1.0 1, mechanically and electronically locked against each other Max. 0.3 W 0 ºC to 35 ºC Required Max. 2 x 2.5 mm2, solid or stranded types Max. 10 mechanical double push-button switches Max. 50 m for 3-wire NYM cable 16 A circuit breaker 2405 - 2480 MHz <10 mW IP20 43 x 43 x 22 mm Zigbee 3.0 certified DUG_Wiser Micro Module Blind_CLP-00 29 Compliance Wiser Micro Module Blind Compliance information for Green Premium products Find and download comprehensive information about Green Premium products, including RoHS compliance and REACH declarations as well as Product Environmental Profile (PEP) and End-of-Life instructions (EOLI). https://checkaproduct.se.com/ General information about Green Premium products Click the link below to read about Schneider Electric's Green Premium product strategy. https://www.schneider-electric.com/en/work/support/green-premium/ Trademarks This guide makes reference to system and brand names that are trademarks of their relevant owners. · Zigbee® is a registered trademark of the Connectivity Standards Alliance. · Apple® and App Store® are brand names or registered trademarks of Apple Inc. · Google PlayTM Store and AndroidTM are brand names or registered trademarks of Google Inc. · Wi-Fi® is a registered trademark of Wi-Fi Alliance®. · WiserTM is a trademark and the property of Schneider Electric, its subsidiaries and affiliated companies. Other brands and registered trademarks are the property of their respective owners. 30 DUG_Wiser Micro Module Blind_CLP-00 Schneider Electric (Australia) Pty Ltd 33-37 Port Wakefield Road Gepps Cross SA 5094 Australia Customer Care: 13 73 28 www.clipsal.com As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication. © 2023 2023 Schneider Electric. All rights reserved. DUG_Wiser Micro Module Blind_CLP-00