User Manual for SECO models including: MU1MWMO146, 2ALZB-MU1MWMO146, 2ALZBMU1MWMO146, MU1MWMO146 Wi-Fi and BT Module, MU1MWMO146, Wi-Fi and BT Module, BT Module, Module
SECO S.p.A. MU1MWMO146 WiFi and BT module 2ALZB-MU1MWMO146 2ALZBMU1MWMO146 mu1mwmo146
User Manual MU1MWMO146 User Manual for FCC Regarding FCC modular approval of MU1MWM0146 Model Name: MU1MWMO146 FCC ID: 2ALZB-MU1MWMO146 This device complies with Part 15 of the FCC rules, and its operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2 MU1MWMO146 User Manual for FCC Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure). The following information must be indicated on the host device of this module. Contains Transmitter Module FCC ID: 2ALZB-MU1MWMO146 or Contains FCC ID: 2ALZB-MU1MWMO146 This device complies with Part 15 of the FCC rules, and its operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. *If it can not be described on the host product, it must be listed on both the host product manual and on the host product package or removable label. 3 MU1MWMO146 User Manual for FCC The following statements must be described on the user manual of the host device of this module; FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: ±20 ppm This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. 4 MU1MWMO146 User Manual for FCC When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person's body. When installing it in a portable equipment. Please describe the following warning to the manual. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. MU1MWMO146 has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth V4.2(BDR/EDR/LE)). Class II permissive change application is necessary using the SAR report. Please contact SECO. Note) Portable equipment: Equipment for which the spaces between human body and antenna are used within 20 cm. Mobile equipment: Equipment used at position in which the spaces between human body and antenna exceeded 20 cm. Antenna Please refer to the Antenna Specification document supplied by SECO or please contact SECO for the detail designation of how to design the Antenna trace. 5Microsoft PowerPoint per Microsoft 365