Intelligent lighting controls | Lumos Controls
Owner's Manual for lumos models including: AFD1, Radiar AFD1 SLAVE DALI Fixture Controller, SLAVE DALI Fixture Controller, DALI Fixture Controller, Fixture Controller
Radiar AFD1/4 - Installation Guide Radiar AFD1/4 - Installation Guide The Installation guide of Radiar AFD1/4 can be accessed here
File Info : application/pdf, 4 Pages, 250.37KB
DocumentDocumentRadiar AFD1 1 SLAVE DALI Fixture Controller FCC ID: 2AG4N-WCAD1N INSTALLATION AND QUICK START SHEET WARNING AND GUIDELINES!!! Read and follow all safety instructions!! DO NOT INSTALL DAMAGED PRODUCT! This product has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced. WARNING : TURN THE POWER OFF AT THE CIRCUIT BREAKER BEFORE WIRING WARNING: Risk of Product Damage Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding equipment should be worn during all installation or servicing of the unit Do not stretch or use cable sets that are too short or are of insufficient length Do not modify the product Do not mount near gas or electric heater Do not change or alter internal wiring or installation circuitry Do not use product for anything other than its intended use WARNING - Risk of Electric Shock Verify that supply voltage is correct by comparing it with the product information Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements All wiring connections should be capped with UL approved recognized wire connectors All unused wiring must be capped Do's Installation should be performed by a qualified electrician Installation shall be in accordance with all applicable local and NEC codes Turn the power OFF at circuit breakers before wiring Observe the correct polarity of output terminal Don'ts Don't use outdoors Avoid input voltage exceeding maximum rating Don't disassemble the products - Specifications Input Voltage Input Current Power Consumption Surge Transient Protection Connection Distance (Device to Device by Mesh) Frequency Range Tx Power Value 90-277VAC 10mA 2W 4kV 30m 2400-2483MHz 8dBm Rx Sensitivity Bus Supply Voltage Bus Supply Current Dimming Range Ambient Temperature Relative Humidity Dimensions -92dBm 11-13VDC 2mA 100% -20-50ºC 20-85% 1.7 x 1.4 x 0.8 In 43 x 35 x 20 mm Remarks Rated Input voltage @ 230 V Active Power L-N, Bi wave In an open office environment (Line of Sight) _ With 150mm external wire antenna _ _ _ _ _ _ L x W x H Product Overview Radiar AFD1 is designed to control AC-powered lighting fixtures supporting Digitally Addressable Lighting Interface. It provides ON/OFF or dimming/tunable control for 1 LED driver It is a part of Lumos Controls ecosystem, which includes controllers, sensors, switches, modules, drivers, gateways, and analytical dashboards. Required tools & supplies Screwdriver Wire nuts INSTALLATION INSTRUCTIONS Installation Steps 1. Turn off the power before wiring and installing the device 2. The controller with a compact formfactor can be installed anywhere within the light fixtures, or within junction boxes. The screw hole available on the controller can be used to fix it firmly. 3. To power the controller, connect the AC Line (Black) and Neutral (Wires) wires from the controller to the mains supply 4. To control the DALI driver, connect the DALI lines to the DALI+ (Purple color) and DALI- (Pink color) wires in the controller. *DALI is polarity insensitive Installing within a light fixture Line (Black) Neutral (White) (Top view of a light fixture) Ground (Pink) DALI- (Pink) DALI+ (Purple) 12VDC (Yellow) You can also install the device within a box On the extrusion or on top of the fixture Recessed Linear Pendant Recessed Troffer High Bay Downlight Wiring Connecting DALI drivers to the Radiar AFD1 controller NL AC Line AC Neutral Radiar AFD1 DALI+ DALI12VDC GND 12VDC Sensor GND Line Neutral DALI Driver DALI + DALI LED+ LED- LED Application LED Fixture Driver Radiar AFD1 WCAD1N Troubleshooting When returning from a Power Outage, lights go back to ON state. There is a delay for the device to turn on/off/dim Lights flickering This is normal operation. Our device has a fail-safe feature forcing the device to go to 50% or 100% and 0-10V at the full output on the loss of power. Alternatively, the device will return to its previous state after the power is restored, as configured using the Lumos Controls mobile app needs to be updated to Alternatively, the device will return to the previous state or a custom state as configured using the Lumos Controls mobile app after the power is restored Check whether you have set up a transition time Check whether connection is as per wiring diagram Check for loose connections Lights did not turn ON Check whether circuit breaker has tripped Check whether fuse has blown Check for loose connections Warranty 5-year limited warranty Please find warranty terms and conditions Note: Specifications may change without notice Actual performance can vary due to end-user environment and application Commissioning Once powered up, the device will be ready to be commissioned via the Lumos Controls mobile app, available for free download on iOS and Android. To begin commissioning, click the `+' icon from the top of the `Devices' tab. The app allows you to preset certain configurations which will be loaded after the device is added. The pre-configurations made using 'Commissioning Settings' will be sent to the devices being commissioned. Once commissioned, the device will be displayed in the `Devices' tab and you can perform individual operations like ON/OFF/dimming on it from this tab. Note: The `Output Channel Configuration' will be `Single Channel' by default. To configure dual channel settings, go to `Additional Settings' and click `Output Channel Settings'. Then select `Controller based color tuning' or `Driver based color tuning' based on the connected driver. Please visit Help center for more details Lumos Controls Application Download the `Lumos Controls' application from Play Store or App Store OR Scan the QR codes to download the `Lumos Controls' application The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by WiSilica Inc. is under license. Other trademarks and trade names are those of their respective owners. 20321 Lake Forest Dr D6, Lake Forest, CA 92630 www.lumoscontrols.com +1 949-397-9330 All Rights Reserved WiSilica Inc Ver 1.1 Jul 2022