Autonics B7VA Series Voice Buzzer Autonics Instruction Manual

Instruction Manual for Autonics models including: TCD220043AD, B7VA Series, B7VA Series Voice Buzzer Autonics, B7VA Series, Voice Buzzer Autonics, Buzzer Autonics, Autonics

Voice Buzzers

File Info : application/pdf, 3 Pages, 2.07MB

B7VA EN-DTE

-|Transparent Guide|-

TCD220043AD
Voice Buzzers
B7VA Series PRODUCT MANUAL
For your safety, read and follow the considerations written in the instruction manual, other manuals and Autonics website. The specifications, dimensions, etc. are subject to change without notice for product improvement. Some models may be discontinued without notice.
Features
· Sound pressure level: up to 90dB±10% (at 1 m) · Mounting hole : Ø72 mm, panel thickness: 6mm · Check operation status with operation indicator (LED indicator) · 8 different alarms · Switch between single or repeat play (internal memory type) · Inserting voice or melody available (external memory type) · Switch between NPN/PNP · IP65 protection rating

Safety Considerations
· Observe all `Safety Considerations' for safe and proper operation to avoid hazards. · symbol indicates caution due to special circumstances in which hazards may occur.
Warning Failure to follow instructions may result in serious injury or death.
01. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic loss.(e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.) Failure to follow this instruction may result in explosion or fire.
02. Do not use the unit in the place where flammable/explosive/corrosive gas, high humidity, direct sunlight, radiant heat, vibration, impact or salinity may be present. Failure to follow this instruction may result in explosion or fire.
03. Check `Connections' before wiring. Failure to follow this instruction may result in fire.
04. Do not connect, repair, or inspect the unit while connected to a power source. Failure to follow this instruction may result in fire or electric shock.
05. Do not use this product close to the ears. Failure to follow this instruction may result in personal injury.
06. Do not disassemble or modify the unit. Failure to follow this instruction may result in fire.
Caution Failure to follow instructions may result in injury or product damage.
01. This unit shall not be used outdoors. Failure to follow this instruction may result in shortening the life cycle of the product.
02. Use the unit within the rated specifications. Failure to follow this instruction may result in fire or product damage.
03. When connecting the power input, use AWG 22-16 (0.30 to 1.25 mm2) cable or over and tighten the terminal screw with a tightening torque of 0.4 to 0.6 N m. Failure to follow this instruction may result in fire or malfunction due to contact failure.
04. For wiring the product, do not pull the wiring excessively or apply excessive force. Failure to follow this instruction may result in product damage or malfunction.
05. Use a dry cloth to clean the unit, and do not use water or organic solvent. Failure to follow this instruction may result in fire or electric shock.
06. Keep the product away from metal chip, dust, and wire residue which flow into the unit. Failure to follow this instruction may result in fire or product damage.
Cautions during Use
· Follow instructions in `Cautions during Use'. Otherwise, it may cause unexpected accidents.
· The power supply should be insulated and limited voltage/current or Class 2, SELV Power supply device.
· Keep away from high voltage lines or power lines to prevent inductive noise. When installing the power line and input signal line closely, use a line filter or varistor at the power line and a shielded wire at the input signal line. Do not use this product near the equipment which generates strong magnetic force or high-frequency noise.
· This unit may be used in the following environments. - Indoors (in the environment condition rated in `Specifications') - Altitude max. 2,000 m - Pollution degree 2 - Installation category II

-|Transparent Guide|-

Ordering Information
This is only for reference, the actual product does not support all combinations. For selecting the specified model, follow the Autonics website.

B7VA - -

Channels 8: 8 channels
Case color K: Black

Power supply D: 12 - 24 VDC
Memory No mark: Internal memory E: External memory

Product Components

· Product × 1

· Instruction manual × 1

· Micro SD card × 1 (external memory type)

Sold Separately
· Micro SD card: BSD-16G

Software
Download the installation file and the manuals from the Autonics website.
DAQMaster
It is the comprehensive device management program for Autonics' products, providing parameter setting, monitoring and data management.

Unit Descriptions Front part

Rear part

Internal memory type

External memory type

Status indicator

LED color Green
Orange

LED status

Description

(

Flashing (

(

) · The product is turned on. · The file transfer is completed from the micro SD card. 01)
) 01) · The file is being transferred from the micro SD card.
) 01) · An error occurred during the micro SD card file transfer. · No audio source exists in the sound channel.

Flashing ( ) · The audio is being played.

01) Only for the external memory type

Volume control switch (VOL.) You can adjust the volume of the buzzer.

Sound terminal COM : It is the common terminal for selecting the sound. When wiring, connect to 12 - 24 VDC for NPN input and connect to the GND for PNP input. S1 to S8 : It is the signal input terminal for selecting the sound.

Supply power terminal : It is the terminal for supplying power (12 - 24 VDC). : It is the terminal for grounding (GND).

Playback count setting switch (MODE) REPEAT : You can set the single play or loop play.

Micro SD card slot It is the space for inserting the micro SD card.

Connections

Be sure not to supply the power to the sound terminals (S1 to S8).
Otherwise, it may result in the circuit damage or malfunction of the product.

Example: NPN input wiring Example: PNP input wiring

· Non-contact input · Contact input

S1 ~ S8 COM

12 - 24 VDC

12- 24 VDC

Sound setting
· When connecting to the desired sound terminal, refer to the 'wiring example' and 'crimp terminal specifications.'
· In the case of the external memory type, the sounds may vary depending on your sound configuration.

Terminals S1 S2 S3 S4

Sounds Police siren sound Fire alarm Ambulance sound Warning sound

Terminals S5 S6 S7 S8

Sounds Alarm sound Doorbell ring Ringtone 1 Ringtone 2

Crimp Terminal Specifications

Crimp terminal for the sound terminals

Refer to the table below to use a suitable ferrules terminal. · The wire range: AWG24-16

L d

8 mm

Ø1.1

Ø2.5

Ø1.3

Ø3.2

10 mm

Ø1.6

Ø3.4

Ø1.7

Ø3.6

Crimp terminal for the supply power terminals

· Fork crimp terminal (mm) · Round crimp terminal (mm)

16.0 4.1

3.0

5.9

Dimensions

· Unit: mm, For the detailed drawings, follow the Autonics website. · This dimensions shows the internal memory type.

18.2 48.7

37.6

Ø90 Ø84 Ø69 81.5

Panel cut-out
· The panel thickness for installation: 6 mm

Ø72

Installation

01. Firstly, make a hole with reference to the panel cut-out.
02. Insert the buzzer into the hole, and wheel the nut clockwise(CW) to firmly fix it. · The nut tightening torque: 5 to 6 N m

-|Transparent Guide|-

Supported Functions

Volume control
You can adjust the sound volume of buzzer using the Volume control switch. Be sure not to turn the switch with excessive force to prevent product damage. · The range of operating torque: 2 to 20 mN m

Switch settings
MIN MAX

Descriptions
· Turn the volume up : Turn the switch clockwise(CW) using the cross-head screwdriver. · Turn the volume down 01) : Turn the switch counterclockwise(CCW) using the cross-head screwdriver.

01) The MIN point does not play muted sound.

Sound playback count setting (internal memory type)

You can set the playback count using the REPEAT switch. · Be sure to input sound signals or supply power again to apply the settings.

Switch settings

OFF

REPEAT

OFF

The range of sound terminals 01)

S1 to S4

S5 to S8

Loop play (factory settings)

Loop play

Single play

Loop play

Single play

01) The playback count setting is applied to only wired terminals in this range.

Import audio sources (external memory type)

Before the begin
· Prepare an micro SD card with the playlist (.BIN file) saved. For detailed information on sound configuration for external memory type, refer to the 'DAQMaster User Manual.' · For micro SD card recognition, supply power to the buzzer and ensure that no signal is input to the sound terminal during this process.

Move the micro SD card file to the buzzer
01. Open the micro SD card slot cover. 02. Insert the micro SD card into the micro SD card slot, aligning it with the indicated
direction. (An alert sound will play once when the micro SD card is inserted.) 03. When the micro SD card file transfer starts, the green LED on the status indicator will
flash. Do not power off the buzzer or remove the micro SD card at this time, as it can damage the audio sources due to file transfer errors. (If an error occurs, you will hear a short beep four times and the orange LED will light up.) 04. When the micro SD card file transfer is complete, a completion alert sound will play once. The transferred audio file will be saved, while the previous audio file will be deleted. 05. After removing the micro SD card, close the micro SD card slot cover.

Specifications

Type

Model

Sound pressure

Signal input method Audio sources 01)

Sound 1

Sound 2

Sound 3

Alarms

Sound 4 Sound 5

Sound 6

Sound 7

Sound 8

Audio file format

Memory card SD card format type Indicator Certification Unit weight (packaged)

Internal memory External memory

B7VA-8KD

B7VA-8KD-E

90 ±10% dB (distance at 1 m)

Compatible with NPN and PNP inputs

Alarm: 8 types

Alarm: 8 types (factory settings)

Police siren sound Fire alarm Ambulance sound Warning sound Alarm sound

DAQMaster : Playlist configuration supported - No. of files: 128 - Storage size: 4 MB

Doorbell ring

Ringtone 1

Ringtone 2

MPEG-1 Audio Layer (MP3), Waveform Audio Format (WAV) 02)

micro SD (SDHC) 03)

FAT32

Status indicator: Green / Orange LED

255 g ( 323 g) 255 g ( 325 g)

01) You can download the 8 types of alarm sounds from our website. For external memory type, changing the audio sources will delete the provided built-in sounds.
02) The WAV file is converted to the MP3 file in DAQMaster.
03) Be sure to use the included micro SD card (BSD-16G). Otherwise, we cannot guarantee the product's performance.

Power supply Power consumption Insulation resistance
Dielectric strength
Vibration
Shock Ambient temperature Ambient humidity Protection ratings Material

12 - 24 VDC 7.2 W 1,000 M (500VDC megger) Between the charging part and the case: 500 VAC 50 / 60 Hz for 1 min 1.5 mm amplitude at frequency 10 to 55 Hz (for 1 min) in each X, Y, Z direction for 2 hours 300 m/s2 ( 30 G) in each X, Y, Z direction for 3 times -10 to 55 , Storage: -20 to 65 (no freezing or condensation) 35 to 85%RH, Storage: 35 to 85%RH (no freezing or condensation) IP65 (Front part, IEC standard) Front cover: ABS, Body: PA6

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002 www.autonics.com | +82-2-2048-1577 | sales@autonics.com

References

autonics.com

Adobe PDF Library 17.0 Adobe InDesign 19.4 (Windows)