Home | Lightware Visual Engineering
Home | Lightware Visual Engineering
User Guide for LIGHTWARE models including: DA4-HDMI20-C Full 4K TPS HDBaseTTM HDMI 2.0 Extenders, DA4-HDMI20-C, Full 4K TPS HDBaseTTM HDMI 2.0 Extenders, TPS HDBaseTTM HDMI 2.0 Extenders, HDMI 2.0 Extenders, 2.0 Extenders, Extenders
DA4-HDMI20-C
File Info : application/pdf, 2 Pages, 1.03MB
DocumentDocumentFront view 12 3 Quick Start Guide DA4-HDMI20-C 1 Power LED 2 Input LED 3 Output LEDs 4 DIP switch 5 Micro-USB port The LED is lit in red when power is applied. The LED is lit in green when HDMI signal is present on the input. The LEDs is lit in green when HDMI signal is present on the respective output. 4-pin DIP switch for EDID setting and HDCP mode selection. Firmware update can be performed through this port. Important Safety Instructions Please read and keep the information in the attached safety instructions supplied with the product before starting to use the device. Introduction Thank you for choosing Lightware's DA4-HDMI20-C 1x4 distribution amplifier, which can distribute and amplify one HDMI input signal to four HDMI outputs. This device supports HDMI video resolution up to 4K@60Hz 4:4:4, including multichannel audio formats. Besides passing EDID information from the display, there are multiple built-in EDID settings that can be selected with the 4-pin DIP switch on the front panel. The device also supports firmware update though a micro-USB port. Features Resolutions of up to 4K@60Hz with 4:4:4 colorspace HDMI 2.0 and 1.x compliant HDCP 2.3 support Supports video resolution downscaling (e.g. 4K to 1080p) based on EDID 18 Gbps bandwidth Advanced EDID management: multiple built-in EDIDs can be selected Built-in equalizer for signal enhancement to avoid signal attenuation in transmission No signal latency, zero frame delay Supports CEC passthrough LEDs indicate current operating status Firmware update via Micro-USB port Rear view 1 2 1 HDMI Input port 2 HDMI Output ports 3 DC 5V barrel port Type-A female HDMI input port to connect an HDMI source. Four type-A female HDMI output ports to connect HDMI displays. DC barrel port to connect an AC power adapter. 4 5 DIP Switch Operation EDID Management The DIP switch represents "1" when in the upper position, and "0" when in the lower position. Switch 1-3 are used for setting the EDID. The DIP switch statuses and their corresponding settings are shown on the top of the product. ID DIP SET Emulated EDID 000- 1 Copy from Output 1234 001- Priority select 1234 123 4 010- Custom EDID 1234 011- 1920x1080p60 1 2 3 4 2ch PCM 100- 3840x2160p30 1 2 3 4 2ch PCM 3 101- 3840x2160p60 2ch PCM 1234 110- 4096x2160p60 1 2 3 4 2ch PCM 111- 3840x2160p60, HDR, 4:2:0 1 2 3 4 2ch PCM If the DIP switch is set to 010- (Custom EDID), but there is no custom EDID present in the device, the EDID of the 101- position will be emulated automatically. HDCP management When the fourth switch is in the upper position, HDCP capability on the input is disabled. When it is in the lower position, HDCP capability is enabled. ON HDCP capability is enabled. 1234 OFF HDCP capability is disabled. 1234 Box Contents Distributor-amplifier SWaafertryanatnyd Info Quick Start Guide Safety and Warranty Info, Quick Start Guide 5V DC Power Adaptor, interchageable plugs Mounting ear pack Firmware Update Please follow the steps below to update the firmware of the device via the Micro-USB port: 1. Connect the device to the PC with a USB cable. 2. Power on the device. The PC will automatically detect a U-disk called "BOOTDISK". 3. Double-click on the U-disk to open it, and take note of a file named "READY.txt". 4. Copy the latest update file (.bin) directly to the "BOOTDISK" U-disk. 5. The "READY.txt" shall turn into "SUCCESS.txt" upon successful firmware update. If the update failed, please check the (.bin) file and then try the process desribed above again. 6. Remove the USB cable after firmware update is complete. Uploading a custom EDID To upload a custom EDID to the device, please follow these steps: 1. Connect the device to a host computer using the micro-USB port. 2. Power on the device (or restart it if it was powered on when plugging the cable in). 3. The computer will now treat the device as a USB drive. 4. Make sure that the custom EDID file is in binary format, contains either 128 or 256 bytes (with CEA extension), and that its extension is .edid. 5. Copy the chosen EDID file to the device. If the upload is successful, a file called "E_SUCC.txt" shall appear on the device. 6. Unplug the micro-USB cable and restart the device. The custom EDID shall be available for choosing. If the upload is successful, the custom EDID can be emulated by setting the DIP switch to the 010- position. The custom EDID remains in the device memory even if it is turned off. Further information on the device is available at www.lightware.com. TAKE CARE OF ME I AM THE ONE AND ONLY USER DOCUMENT FOR THIS PRODUCT Contact Us sales@lightware.com +36 1 255 3800 support@lightware.com +36 1 255 3810 Lightware Visual Engineering PLC. Budapest, Hungary Doc. ver.: 1.1 19210067 Specifications General Compliance....................................................................................................CE, UKCA EMC Immunity ............................................................................... IEC/EN 55035:2017 EMC Emission ............................................................................... IEC/EN 55032:2015 Safety.......................................................................................... IEC/EN 62368-1:2014 Warranty ............................................................................................................. 3 years Power supply (Input)..............................................................................100V~240V AC Power supply (Output)....................................................................................5V DC 1A Power consumption (max)..................................................................................... 2.5W Operating temperature ............................................................................ -10°C~+55°C Storage temperature................................................................................ -25°C~+70°C Operating humidity ......................................................................................... 10%-90% Enclosure Enclosure material......................................................................................... 1mm steel Dimensions (mm) ...................................................................142(W)x17.6(H)x70.4(D) Weight.....................................................................................................................260g Mechanical drawing 17.60 mm Rear side Top side 70.40 mm Control Front panel control.............................................................................. Yes, EDID switch LED indicators .......................................Live, Video Input Status, Video Output Status EDID emulation.............................................................. Advanced EDID management EDID memory ......................................................... 5 factory presets, 1 programmable EDID support ................................................................................................. EDID v1.3 Control ..............................................................................Micro USB-B type connector HDMI Ports Connector ..................................................................................... Type-A female HDMI Standard ........................................................................................ HDMI 1.4, HDMI 2.0 Maximum resolution .......................................................4096x2160@60Hz, 8 bit color HDCP compliancy .........................................................................HDCP 2.3 compliant 3D support ................................................................................................................ Yes Reclocking ................................................................................................................ Yes Input cable equalization...............................................................................+12dB fixed Digital audio formats...................................................................... All HDMI2.0 formats .........................................multi-channel PCM, Dolby True-HD, DTS-HD master audio CEC ............................................................................................................... Supported Front side 142.00 mm 1234 Bottom side