BALLAR B29 Smart Lock User Manual and Operation Guide

1. Product Parameters

2. Operation Guide

2.1 Factory Reset

For first-time use, perform a factory reset. Long press the "Factory reset" button. A beep will sound every 1 second. After 5 seconds, a prompt will appear: "Factory reset, press the # button to confirm". Press the # button to confirm the reset. The voice prompt will be "Successful initialization".

2.2 Experience Mode

In the factory state, entering any fingerprint, sensor card, or the default factory password (123456) allows unlocking. Upon successful unlocking, the voice prompt will be "unlocked, demonstration mode, please register as a user".

3. Door Lock Menu

Support entering the menu through the following methods:

1. Short press the door setting button once.
2. Press the "*" and "#" buttons.

Function Menu

The system will play a voice prompt: "For administrator settings, press 1. For user settings, press 2. For system settings, press 3. For factory settings, press 4. For information queries, press 5".

Language selection is available:

• Press 555666882 and confirm with '#' for Thai language.
• Press 555666883 and confirm with '#' for Arabic.
• Press 555666884 and confirm with '#' for Spanish.
• Press 555666886 and confirm with '#' for Russian.
• Press 555666887 and confirm with '#' for Portuguese.
• Press 555666888 and confirm with '#' for switching between Chinese and English.

Flow: In the initialization state [next step] Wake-up Status [next step] Press the *# key.

Press the *# key

Please enter the administrator information (e.g., default password 123456) and press '#' to confirm.

Press 1 for administrator settings

• Add an administrator: Enter administrator information (set password) and press '#' to confirm or '*' to cancel.
• Delete an administrator: Enter administrator code and press '#' to confirm or '*' to cancel.

Press 3 for network settings

• Hotspot connection: Press '1' to select hotspot connection or '*' to cancel.
• Intelligent connection: Press '2' to select intelligent connection or '#' to cancel.

Press 2 for user settings

• Add a user: Enter unlock information (set password) and press '#' to confirm or '*' to cancel.
• Delete a user:
  • Delete by number: Enter number and press '#' to confirm or '*' to cancel.
  • Delete all: Press '#' to confirm or '#' to cancel.

Press 3 for system settings

• Voice settings:
  • Open voice: Press '1' to turn on voice or '*' to cancel.
  • Close voice: Press '2' to turn off voice or '*' to cancel.
• Clear unlock mode:
  • Single unlocking: The operation is successful.
  • Combination unlocking: The operation is successful.
  • Enable long unlocking: The operation is successful.
  • Disable long unlocking: The operation is successful.
• Time settings: Enter setting time and press '#' to confirm or '*' to cancel.
• Room number settings: The default room number is 8888, with a setting range of 0-9999. Press '#' to confirm or '*' to cancel.
• Anti-prying settings: Press '5' to select "Anti-prying Settings" (Turn Anti-prying detection on/off).

Press 4 to restore to factory settings

Press '#' to confirm for restoring to factory settings.

Press 5 for information inquiry

• Time inquiry: Enter query time and press '#' to confirm.
• Number inquiry: Enter query number and press '#' to confirm.
• Stock inquiry: Please press '3' for stock.

3.1 Add regular users

Flow: Press *# to enter [next step] Enter the administrator fingerprint/password/sensor card [next step] Press 2 to select "User Settings" [next step] Press 1 to select "Add User" [next step] Follow the voice prompt to enter the fingerprint, password or sensor card [next step] XXX record successfully.

Fingerprint

To add a fingerprint, press it 5 times. The fingerprint cannot be entered repeatedly. When registering, lift the finger and press different parts of the same finger for better verification of unlocking.

• If the fingerprint is full, the voice will play "alarm sound" + "stock is full".

Password

If the passwords entered twice do not match, the voice will play: "alarm sound". The registration password is 6-8 digits. Pressing '#' with less than 6 digits is invalid.

• If the password you entered has already been registered, the voice will play: "alarm sound" + "duplicate information".
• If the password stock is full, the voice will play "password stock is full".

Induction card

• If the induction card has already been registered, the voice will play: "alarm sound" + "duplicate information".
• If the induction card stock is full, voice playback will show "Card stock is full".
• If the user is fully registered, voice play "stock is full".

3.2 Add an administrator

The process of adding an administrator is consistent with adding a regular user. If 9 administrators have been added, the voice playback will indicate a "margin of 0".

3.3 Delete administrator user

3.3.1 Delete by number

Flow: Press *# to enter [next step] Enter the administrator fingerprint/password/sensor card [next step] Press 2 to select "User Settings" [next step] Press 2 to select "Delete Administrator" [next step] Enter the number of the administrator to be deleted [next step] Operate successfully.

Note: The administrator user currently validated in the menu cannot be deleted.

3.4 Delete regular users

3.4.1 Delete by number

Flow: Press *# to enter [next step] Enter the administrator fingerprint/password/sensor card [next step] Press 2 to select "User Settings" [next step] Press 2 to select "Delete User" [next step] Enter the number of the user to be deleted [next step] Operate successfully.

• If there are no regular users, the voice will play: "Stock 0".
• If the number is not registered, the voice will play: "Alarm sound" + "Operation failed".

3.4.2 Delete all

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 2 to select "User Settings" [next step] Press 2 to select "Delete All" [next step] Operate successfully.

3.5 Networking settings

1. Add network

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "Networking Settings" [next step] Press 1 to select "Administrator Settings" [next step] Press 1 to select "Hotspot connection" [next step] In network configuration...... [next step] Operate successfully.

2. Delete network

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "Networking Settings" [next step] Press 1 to select "Administrator Settings" [next step] Press 3 to select "Delete Connection" [next step] Delete..... from the connection [next step] Operate successfully.

Lock end operation steps: Enter the settings menu, press "1" to enter administrator settings, press "3" to enter networking settings, press "1" to enter hotspot connection.

APP operation steps: Please refer to the user manual for the APP selected by the customer.

3.6 System settings

3.6.1 Unlock mode

The system plays the voice: "1. Single unlock, 2. Combination unlock".

Single unlock flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "System Settings" [next step] Press 2 to select "Unlocking Mode" [next step] Press 1 to select "Single Unlock" [next step] Operate successfully.

Combination unlock flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "System Settings" [next step] Press 2 to select "Unlocking Mode" [next step] Press 2 to select "Combination Unlock" [next step] Operate successfully.

Initialization state note: If in initialization state, play voice: "alarm sound" + "operation failure" + "stock 0". If the number of users is less than 1 group, play the voice: "alarm sound" + "operation failure" + "stock 1".

3.6.2 Room number setting

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "System Settings" [next step] Press 4 to select "Room Number Settings" [next step] Enter room number [next step] Operate successfully.

Enter the room number setting menu and the voice prompt will be "Room number XXXX, please modify". The default room number is 8888, with a setting range of 0-9999. If the room number is entered with 4 digits, it will be reset to the factory settings.

3.6.3 Anti prying settings

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "System Settings" [next step] Press 5 to select "Anti-prying Settings" (Turn Anti-prying detection on/off).

3.6.4 Voice settings

1. Open voice

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "System Settings" [next step] Press 1 to select "Voice Settings/Language Selection" [next step] Press 1 to select "Open voice" [next step] Open voice [next step] Operate successfully.

2. Turn off voice

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "System Settings" [next step] Press 1 to select "Voice Settings/Language Selection" [next step] Press 2 to select "Close Voice" [next step] Close voice [next step] Operate successfully.

3.6.5 Time setting

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 3 to select "System Settings" [next step] Press 3 to select "Time Settings" [next step] Enter year (1970-2099) [next step] Enter month (01-12) [next step] Enter date (01-31) [next step] Enter time (00-23) [next step] Enter min (00-59) [next step] Press the '#' button to confirm [next step] Operate successfully.

3.6.6 Information query

1.Query by time

Flow: Press *# to enter [next step] Enter the administrator fingerprint password/sensor card [next step] Press 5 to select "Information Query" [next step] Press 1 to select "Query by Time" [next step] Enter time [next step] Enter year (1970-2099) [next step] Enter month (01-12) [next step] Enter date (01-31) [next step] Press the '#' button to confirm.

4. Unlock operation

4.1 Unlock outside the door

The user's fingerprint and password sensor card have been successfully verified, and the motor is turning forward to unlock. After successfully unlocking, the voice prompt will be "unlocked".

Attention:

1. Please keep the sensor card safe to prevent it from being copied.
2. Please check if there are any foreign objects on the surface of the fingerprint sensor to prevent fingerprint data from being tampered with.

5.Doorbell function

Press the "doorbell" button on the door lock to sound a "ding-dong..." doorbell. If connected to the network, the message "requesting remote unlocking" will be played after the doorbell.

6.Test opening the freezing function

When the number of consecutive errors in fingerprints, passwords, and sensing cards within 5 minutes is ≥ 3, an audible and visual alarm will be issued. When the number of consecutive errors within 5 minutes is ≥ 5 times, the system freezes for 90 seconds and cannot recognize fingerprints, passwords, or sensing cards for another 90 seconds.

7.Battery level detection

• When the battery voltage is below 4.8V, the system will prompt "Low battery, please replace the battery" every time the user wakes up.
• When the voltage is below 4.2V, the wake-up system voice prompts "Low battery, please replace the battery, the system is locked", and cannot perform fingerprint, password, or sensor card door opening actions.

Attention: If the battery is low, please charge it in a timely manner to avoid shutting down after running out of battery.

8. Anti prying alarm

When the anti prying alarm is triggered and continues for 60 seconds, the user cannot operate the keyboard. The alarm status can be lifted by registering the user card or fingerprint.

9. Emergency power supply

When the battery is depleted and there is no key, an external power supply can be connected, and the door can be opened according to the normal operating procedures.

Attention:

1. Please charge the emergency power promptly after opening the door.
2. It is recommended to use a power bank or charger with an output current of 2A or above for external power supply.

10.Some shortcut keys

• Quick key settings for turning on or off the anti pry alarm function: "4+#+Administrator verification" (fingerprint password or card) can turn on or off the anti pry alarm function.
• When an anti-prying alarm occurs, the entered fingerprint or card can be used to clear the alarm or wait for the 60S system to automatically clear it.
• Time query shortcut key: 0+5+# broadcasts the current system time.
• Version number query shortcut key: 0+# broadcasts the current system version number.
• Room number query shortcut key: 0+1+# broadcasts system room number.

Language selection shortcut keys (In the initial state):

• 555666882, press '#' to confirm Thai.
• 555666883, press '#' to confirm Arabic.
• 555666884, press '#' to confirm Spanish.
• 555666886, press '#' to confirm Russian.
• 555666887, press '#' to confirm Portuguese.
• 555666888, press '#' to confirm switching between Chinese and English.

11.APP networking operation instructions

Networking Instructions (Hot Distribution Network & Intelligent Distribution Network)

1. Download the app: Doodle Smart. Open Doodle Smart and click on "Add Device" or "+" in the upper right corner.
2. On the Add Device page, in the Camera/Lock menu, click on "Door Lock (Wi Fi)".
3. Ensure that the phone is connected to WiFi and the WiFi is 2.4GHz. Click Next.
4. Then click on the door lock to enter the distribution network status. Click on confirm and proceed to the next step on the Doodle Smart APP.
5. Wait for the successful distribution network.

12. Revision History

FCC and RF Exposure Notes

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important: Change or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.

The devices have been evaluated to meet general RF exposure requirement; the device can be used in portable exposure condition without restriction.