This manual provides comprehensive information for the installation, operation, and maintenance of the Blink EV 250 Smart EV Charger.
Copyright © 2024 Blink Charging. All rights reserved.
Blink Charging Co. and its affiliates are referred to as "Blink".
No part of this document may be reproduced without express written permission from Blink. While efforts are made to ensure accuracy, inconsistencies may occur and should be reported to Blink. Changes to this manual may be made at any time without notice.
Disclaimer of Consequential Damages: Blink is not responsible for the use or application of the materials in this manual or for damages arising from their use. Installation is intended for qualified professionals. Electricity is dangerous; if you have any doubts, hire a licensed electrician. Always disconnect power before working with electrical circuits and follow local electrical codes.
Notice: Modifications not expressly approved by the party responsible for compliance may void the user's authority to operate the equipment.
Blink and the Blink logo are registered trademarks of Blink. SAE J1772™ is a trademark of SAE International®.
Contact Blink: 2404 W. 14th St., Tempe, AZ 85281, (888) 998-2546, www.BlinkCharging.com
Important Safety Instructions
Read all instructions before installing or using the Blink EVSE. Pay attention to WARNING and CAUTION markings.
General Warnings
- ⚠️ RISK OF PERSONAL INJURY
- ⚡ RISK OF ELECTRIC SHOCK
- ? RISK OF FIRE
- ⚠️ RISK OF DAMAGE TO THE EQUIPMENT
Installation and Usage Precautions
- Installation must be performed by a qualified technician.
- Blink is not responsible for injury or damage caused by improper installation.
- Ensure installation procedures and materials comply with local building codes and safety standards.
- Always follow applicable codes and standards. Consult a licensed electrician if unsure.
- Never work with live voltage; always disconnect power first.
- Do not disassemble or modify the charger; risk of electric shock or fire.
- Do not use the charger if the connector or vehicle inlet is damaged.
- Avoid contact with electricity or sharp objects on charger connector terminals.
- Do not use in wet conditions or immerse the charger or connector in liquids.
- Store the charging cable properly to avoid moisture.
- Do not use the charger if it is damaged, cracked, or inoperable.
- Do not pour liquids on the charger.
- Prohibited Usage: Do not use when moisture is present on the connector/inlet, or when charger power is off (user-forced charging is prohibited).
- Use only the designated EV battery; do not use for other purposes.
- Prevent collisions between the charger and vehicle; stop operation and contact the manufacturer if impacted.
- Do not use outside specified temperature ranges; use supplementary devices if necessary.
- Do not operate the vehicle while it is charging.
- Do not damage the product; replace with new parts if damage occurs.
- Do not touch uninsulated parts; risk of electric shock.
- Before disassembly/assembly, turn off all power to prevent electric shock and death.
- Perform appropriate grounding work according to regulations.
- Disconnect the charger connector with both hands, ensuring alignment.
- Supervise children during charging.
- Disconnect the EV and charger before inspection; risk of shock even with power off.
- Ensure no liquids or foreign substances enter the charger.
- Do not place flammable materials near the charger.
- Users must follow local electrical safety regulations.
- Do not disconnect the connector during charging; may damage the connector or charger.
- Do not operate the charger in an abnormal state.
- Contact the service manager or manufacturer for any fatal impact or damage.
- Dusty environments require frequent maintenance.
- Wait 5 minutes after blocking power before inspecting/disassembling.
- Always turn off the charger's power when inspecting or maintaining.
- Do not forcefully disconnect the plug and socket; use the cancel button to end charging.
- Do not perform vehicle maintenance (washing, repair) during charging.
- Avoid charging during peak hours (Summer: 13:00-17:00; Winter: 11:00-12:00, 18:00-19:00) for power demand stability.
- This station is for EV charging only. Unauthorized use is not covered.
- Hire a certified electrician for assembly/disassembly.
Product Inspection Upon Receipt
Upon receipt, unpack and check for shipping damage. Record any damage with video/photo and contact the shipping company. Compare the packing list with the purchase order; contact Blink within 1 month for discrepancies.
Storage Environment and Method
Store in a clean, dry environment between -40°F to 149°F (-40°C to 65°C). Transport in an upright box to prevent scratches.
Product Specifications
| Specification | Details |
|---|---|
| Model Number | ELA007C03 |
| Operating Condition | Indoor/Outdoors |
| Charging Status | Mode 3 (IEC 61851-1) |
| AC Inlet Voltage | 208~240 VAC, 1 Phase |
| AC Outlet Current | 32A / 50Hz/60Hz |
| Output Current | 6A~32A (dynamic load balancing) |
| Indication | E-ink Display / RGB LED |
| Connectors | SAE J1772 (IEC 62196 Type 1) 2M / 7.4 M Type 2 / GB/T |
| Functional Safeties | Over current protection, Ground continuity check, Relay fault detection, Control by internal temperature of Charger |
| Leakage Current Protection | Integrated, no additional required (CCID20) |
| Radio Frequency | Wi-Fi: 2.4 GHz, 802.11b/g/n; NFC: 13.5598 MHz; Bluetooth LE: 2.4 GHz |
| IP Protection | IP 55 |
| Size of Charger | 306 mm x 395 mm x 116 mm (W x H x D) |
| Operating Temp. | -30°C to 50°C (-22°F to 122°F) |
| Storage Temp. | -40°C to 65°C (-40°F to 149°F) |
Labels and Box Contents
Labels
The label includes Model No.: ELA007C03, Rated Input/Output Voltage: 208/240Vac, Max Current: 32A, Max Output Power: 7.7kW, Nominal Frequency: 60Hz, Serial No.: EV-SCA-000003. It contains WARNINGs: "Do not install on or over combustible surfaces." and "AVERTISSEMENT: Ne pas installer sur ou au-dessus de surfaces combustibles." It also includes CAUTION: "Do not use this product if there is any damage to the unit. Risk of electric shock. Do not remove cover or attempt to open the enclosure. No user serviceable parts inside. Refer servicing to qualified service personnel." and WARNING: "This device is intended only for charging vehicles not requiring ventilation during charging. This device provides an automatic reset feature." and PRÉCAUTION/AVERTISSEMENT statements in French. Certifications include cULus.
Contains
- 1. Smart Charger
- 2. Cable Rest
- 3. Charging Cable
- 4. Key
- 5. Screw Anchor & Anchor Bolt
- 6. Insulated Ring Terminal (M6)
- 7. Guidebook for Installation
- 8. Guide Paper
Parts
The package includes the Smart Charger, Cable Rest, and Charging Cable. The kit contains: 1x Guide Paper, 2x Keys, 7x Screw Anchor & Anchor Bolt (M4x40), 7x Insulated Ring Terminal (M6). Ensure to use the provided parts when assembling.
Installation Instructions and Operations
Required Tools
- Hand Drill
- Wire Stripper
- Ruler
Installation Steps
- When installing or connecting the power input line, turn off the power and ensure the product's IP rating is maintained.
- Install the charger where the connector can easily reach the vehicle inlet.
- The charger requires wireless internet. Obstacles like drywall, plastic, wood, metal, mirrors, brick, concrete can interfere with wireless signals. Check radio reception at the installation site. If a mobile device has service (3G, LTE, Wi-Fi), the charger should connect.
- When wiring the power input line, identify the voltage (L), neutral (N), and ground (G) wires. Confirm single-phase power (220 VAC) between voltage and neutral wires. Incorrect wiring (e.g., three-phase 380 VAC) can damage the charger's fuse.
Install Guide
Important: Ensure the AC power circuit breaker is OFF before starting.
Step 1: Mounting Bracket
Keep the Guide Paper attached to the wall. Assemble the screw anchor through the wall using a 0.24in drill. Recommended: Position the bottom end of the guide paper above 55.1 inches from the floor.
Step 2: Secure Charger to Wall
After opening the Charger, use the accompanying anchor bolt to secure it to the wall through a white rubber cap. Do not remove the white rubber cap; it remains in place.
Step 3: Access Terminal Base
Remove the plastic terminal base cover. The cover can be removed when the hooks are gathered inwards. Be careful not to break the hooks.
Step 4: Connect Power Line
Connect the power line using the enclosed Insulated Ring Terminal (M6) after checking the L/N/G wires and ensuring adequate torque (1.84 lbf.ft). Assemble the removed terminal base cover. Ensure the power source connection to the Insulated Ring Terminal is insulated to prevent short circuits.
Step 5: Lock Charger
Insert the enclosed KEY into the center of the right side of the Charger and turn it counter-clockwise (CCW) to lock. Ensure it is locked properly.
Step 6: Final Setup
After installing the cable rest, set up the wires and Charging Cable, ready for use.
Status and Indication of LEDs
Normal Scenario
- Standby Mode: White LED light detected, charging begins via QR code authentication.
- Charging Preparation: White LED blinks while vehicle recognition/server authentication is in progress.
- Charging: Blue LED breathes slowly once charging starts. Current charging amount is displayed.
- Charging Complete: LED remains illuminated when charging is finished. Place the connector back in its place.
Warning UI / Error Screens
- NFC Authentication: Orange LED blinks if an unauthorized card is tagged.
- Connector Recognition: Orange LED blinks after 2 minutes of disconnection post-authentication, returning to standby.
- Network/Internal Error: Red LED blinks in case of network or internal product issues.
- Emergency Stop: Red LED blinks for 5 seconds after the emergency stop button is pressed, then returns to the prior UI.
- Unavailable Mode: Purple LED lights up when remote unavailable mode is set.
- Firmware Update: Purple LED breathes slowly for up to 10 minutes during the update process.
Warranty
Blink Charging guarantees charging equipment for 3 years from the manufacturing date against product malfunctions caused by material or manufacturing defects, or technical flaws, subject to normal use.
If a malfunction occurs within the warranty period, Blink will replace the product at no charge. The customer must notify Blink within 1 month of discovering the malfunction via phone or email.
Blink will confirm the issue and replace the product free of charge if the defect is confirmed. If the malfunction is due to user negligence, repair will be at the customer's cost.
In case of user negligence, the customer must notify Blink's customer center within 1 month of occurrence/discovery and send the product to Blink's headquarters at the sender's expense.
