無標題文件
Installation Guide for velleman models including: Mobile Phone Surveillance, Software, Mobile Phone Surveillance Software
GPRS / 3G MOBILE PHONE The setting interface of each mobile phone may vary depending on its individual brand. Therefore, the interface shown below only illustrates the main functions of the application, and is for reference only.
For details, please refer to its individual user manual, or check with your local network operator or service provider.
File Info : application/pdf, 14 Pages, 731.42KB
DocumentDocumentSoftware Installation & Setup for Remote Surveillance via GPRS / 3G Mobile Phones or PDA Table of Contents CHECKLIST BEFORE USING ......................................................................................................................... 3 INSTALLATION & SETUP ............................................................................................................................. 4 Software Download ...................................................................................................................... 4 GPRS / 3G MOBILE PHONE............................................................................................................ 6 WINDOWS MOBILE PHONE .......................................................................................................... 8 AVAILABLE FUNCTIONS............................................................................................................................ 11 GPRS / 3G MOBILE PHONE.......................................................................................................... 11 WINDOWS MOBILE PHONE ........................................................................................................ 12 CHECKLIST BEFORE USING Make sure your PDA or mobile phones conform to the following requirements: Device WINDOWS MOBILE PHONE Make sure ... The operating system is Windows Mobile 5.0 Packet PC / 6.0 Professional*. Windows Mobile 5.0 Smartphone / 6.0 Standard is NOT supported. J2ME MIDP2.0 is supported. Internet services via WiFi or GPRS / 3G networks are subscribed and available to use. For details, please check with your local network operator or service provider. GPRS / 3G Mobile Phones J2ME is supported. iPhone Internet services via GPRS / 3G networks are subscribed and available to use. For details, please check with your local network operator or service provider. The port number of the connected device (such as DVR or network camera) is NOT 80. The suggested port number is 88. Go to the application store and search eagleeyes. Download the iPhone compatible software * We do not guarantee the compatibility of the mobile surveillance software in every touch panel PDA brand with the operating system of Windows Mobile 5 Packet PC / 6.0 Professional. NOTE: First of all you have to set up the network configuration for the DVR and router. Check if you can log into the DVR via a PC connected to another modem (see diagram) PC Router 1 Modem 1 Internet DVR Router 2 Modem 2 INSTALLATION & SETUP Software Download STEP1: To download the software for mobile surveillance, please visit the following website address from your PDA or mobile phones: http://211.75.84.102/fae/MobileAP/index.html or http://www.eagleeyescctv.com/ NOTE: The Internet access setting via WiFi or GPRS / 3G networks varies depending on different PDA or mobile phone brand. For details, please refer to its individual user manual, or check with your local network operator or service provider. NOTE: You might be charged for Internet access via WiFi or GPRS / 3G networks. For the Internet access rate details, please check with your local network operator or service provider. You will see the following five applications to download: o BackBerry Software o GPRS / 3G Software o EagleEyes (J2ME New version) o EagleEyes (For WinCE) o EagleEyes (For WinCE New Version) STEP2: Select the application you need and start downloading. To know which program you should download, please refer to the following table: Device Symbian mobile DVR model DVR4MQAEE, DVR8N and DVR8N2 download software GPRS/3G Software Symbian mobile Windows mobile DVR4H, DVR4L3, DVR4L4, DVR4L5 and DVR16H1 DVR4MQAEE, DVR8N and DVR8N2 EagleEyes(J2ME NewVersion) EagleEyes(For WinCE) Windows mobile BlackBerry iPhone DVR4H, DVR4L3, DVR4L4, DVR4L5, DVR8L1, DVR16L1 and DVR16H1 DVR4L3, DVR4L4, DVR4L5, DVR4H, DVR8L1, DVR16L1 and DVR16H1 DVR4L3, DVR4L4, DVR4L5, DVR4H, DVR8L1, DVR16L1 and DVR16H1 EagleEyes(For WinCE New Version) BlackBerry_Software iTunes application store STEP3: Follow the on-screen instructions after downloading. For mobile phones, the application will save to the location you specified. For PDA, the application will save to "Programs". GPRS / 3G MOBILE PHONE The setting interface of each mobile phone may vary depending on its individual brand. Therefore, the interface shown below only illustrates the main functions of the application, and is for reference only. For the actual display, please refer to your own mobile phone. With GPRS / 3G software installed STEP1: Go to the location where you save the application, and you will see the item "Supervisor". STEP2: Select "Supervisor" to key in the information necessary for DVR or network camera remote access. 1. IP Enter the IP address or hostname (ex. dyndns) of the device you want to connect. 2. PORT Enter the port number used by the device you want to connect. You can use the port number from 0 ~ 65536 except 80. It's recommended to use 88. 3. UserName Enter the user name used to access the DVRe you want to connect. 4. PassWord Enter the password used to access the device you want to connect. STEP3: Make sure the information above is correct, and confirm the connection set to start accessing the device remotely. With EagleEyes (J2ME New version) installed STEP1: Go to the location where you save the application, and you will see the item "EagleEyes". STEP2: Select "Connect & View" to go to the setting page, similar as follows. Key in the information necessary for DVR or network camera remote access. Select "Connect & View" Create New Connection Set 1. Host Name Give a name for this connection set. 2. User Name Enter the user name used to access the DVR you want to connect. 3. Password Enter the password used to access the DVR you want to connect. 4. IP Enter the IP address or hostname (ex. dyndns) of the device you want to connect. 5. Port Enter the port number used by the device you want to connect. You can use the port number from 0 ~ 65536 except 80. It's recommended to use 88. STEP3: Make sure the information above is correct, and confirm the connection set to save the setting, and at the same time, you will return to the previous layer. STEP4: Select "Connect & View" again, and select the connection set you just created to start connecting to the device you want. PDA The setting interface of each PDA may vary depending on its individual brand. Therefore, the interface shown below only illustrates the main functions of the application. For the actual display, please refer to your own PDA. With EagleEyes (For WinCE) installed STEP1: Go to "Programs" "EagleEyes" to go to the setting page. STEP2: Click "Device" to add a connection set, and key in the information necessary for DVR or network camera remote access. Create New Connection Set Edit Connection Set Connection Set Created 1. Label Give a name for this connection set. 2. (User Name) Enter the user name used to access the DVR you want to connect. 3. (Password) Enter the password used to access the DVR you want to connect. 4. IP Enter the IP address or hostname (ex. dyndns) of the device you want to connect. 5. Port Enter the port number used by the device you want to connect. STEP3: Make sure the information above is correct, and confirm the connection set to save the setting, and at the same time, you will return to the previous layer. STEP4: Select the connection set you just created to start connecting to the device you want. With EagleEyes (For WinCE New version) installed STEP1: Go to "Programs" -> "EagleEyes" to go to the setting page. STEP2: Click "NEW DEVICE" to add a connection set, and key in the information necessary for DVR or network camera remote access. Create New Connection Set Edit Connection Set Connection Set Created 1. Name Give a name for this connection set. 2. Transfer Method Select TCP or UDP. 3. IP Address Enter the IP address or hostname (ex. dyndns) of the device you want to connect. 4. Port Enter the port number used by the device you want to connect. 5. User Name Enter the user name used to access the DVR you want to connect. 6. Password Enter the password used to access the DVR you want to connect. 7. Stream Format Select MPEG4, JPEG or H.264 (if available). 8. AV Option Select VIDEO, or VIDEO / AUDIO. STEP3: Make sure the information above is correct, and confirm the connection set to save the setting, and at the same time, you will return to the previous layer. STEP4: Select the connection set you just created to start connecting to the device you want. AVAILABLE FUNCTIONS When the installation is completed, you can start the remote surveillance via your device now. The functions available are depending on the remote device you have, and the software you installed. For details, please refer to the following sections. GPRS / 3G MOBILE PHONE With GPRS / 3G software installed a) DVR Mode - Single channel switch - 4-cut / 9-cut / 16-cut display mode switch b) PTZ Mode - Hot point - Auto pan - Zoom in / out - Focus in / out DVR Mode PTZ Mode With EagleEyes (J2ME New version) installed DVR Mode - Single channel switch - 4-cut / 9-cut / 16-cut display mode switch - Quality change DVR Mode - Main Panel DVR Mode - Quality Select DVR Mode - Quality Options WINDOWS Mobile With EagleEyes (For WinCE) installed a) DVR Mode - Single channel switch - 4-cut / 9-cut / 16-cut display mode switch - Snapshot b) PTZ Mode (from left to right) - Preset point 1~16 selection (switch to DVR and click "CH") - Focus near / far - Zoom in / out - Max Zoom in / out - Auto pan - Pan / tilt / zoom control DVR Mode PTZ Mode With EagleEyes (For WinCE New version) installed a) DVR Mode - Record / playback at the remote site - Playback - Channel switch - Remote independent operation - 4-cut / 9-cut / 16-cut display mode switch - Quality change b) PTZ Mode - Record at the remote site - Pan / tilt / zoom control - Auto pan - Auto Tracking - Focus near / far - Preset point 1~16 selection DVR Mode PTZ Mode