Instructions for ViZULO models including: LED Luscinia post top LED luminaire
File Info : application/pdf, 6 Pages, 12.73MB
DocumentDocumentVIZULO Luscinia post top LED luminaire
LED module and driver replacement (dismantling) instruction
IEC
EN 60598
220 - 240 V AC
05 IK10 IP66
min - 40°C
max + 50°C
(+35°C)*
* Depends on configuration. Check label or technical specification. * Atkargs no konfigurcijas. Skatt marjumu vai tehnisko specifikciju. * . .
31-08-2021
SIA VIZULO Laucu Lejas, Iecava, Latvia, LV-3913 www.vizulo.com
T10
T20
T25
1/6
PCB module replacement | PCB moduu maia | PCB
Danger! | Bstami! | ! Before disassembling the luminaire, check if it is disconnected from the power grid. Pirms gaismeka demontzas prbaudiet, vai tas ir atvienots no elektrisk tkla. , .
1
Unscrew the lid from the body and lift it Atskrvjiet vku no korpusa un pacieliet to
2 Disconnect the PCB module from the driver Atvienojiet PCB moduli no barosanas bloka PCB
2 1
T25
3
*Pay attention to the lense direction!
Unscrew the PCB module, replace it and screw it back into place Atskrvjiet PCB moduli, nomainiet to un pieskrvjiet viet
PCB ,
x4
x4
T10
4 Connect the PCB module to the driver Pievienojiet PCB moduli barosanas blokam PCB y
5
1
Lower the lid and screw it back on Nolaidiet vku un pieskrvjiet to
2
White ( + ) Black ( - )
T25
2/6
LED driver replacement | LED draivera maia | LED
Danger! | Bstami! | ! Before disassembling the luminaire, check if it is disconnected from the power grid. Pirms gaismeka demontzas prbaudiet, vai tas ir atvienots no elektrisk tkla. , .
1
Unscrew the lid from the body and lift it Atskrvjiet vku no korpusa un pacieliet to
2
2 1
Unscrew the cover plate from the lid Atskrvjiet aizsegplksni no vka
T25
T25
3
Turn the cover plate over
4
Make a reference picture of the wiring
Apgrieziet aizsegplksni otrdi
Uzmiet references bildi vadu slgumam
180°
5
Unscrew the EQUI wire Atskrvjiet EQUI vadu
6
Disconnect the wires from the driver Atvienojiet vadus no barosanas bloka
EQUI
press
pull T20
3/6
LED driver replacement | LED draivera maia | LED
7
Unscrew the LED driver, replace it and put it back into place
Atskrvjiet barosanas bloku, nomainiet to un nolieciet viet
LED ,
old new
T20
8
Screw in the EQUI wire and the the driver
Pieskrvjiet EQUI vadu un barosanas bloku
EQUI
3N
9
DA/L DA/N L N
EQUI NTC COM NTC Sig LED2+(LV) LEDLED1 +(HV)
black white brown blue
black
bwlhacitke
T20 Consult the reference picture Apskatieties references bildi
PHOTO
4/6
LED driver replacement | LED draivera maia | LED
10
Connect the wires to the driver Pieienojiet vadus pie barosanas bloka
11
Turn the cover plate over Apgrieziet aizsegplksni otrdi
180°
push
12
Screw the cover plate onto the lid
13
Pieskrvjiet aizsegplksni pie vka
Lower the lid and screw it back on Nolaidiet vku un pieskrvjiet to
1
2
5N
T25
T25
5/6
Terms of use and maintenance
Before luminaire is turned on, it should be mounted according with this mounting instruction or any other applicable regulations.
Mounting instructions
Mounting of luminaire must be performed by a qualified person according with following instructions: · The warranty of luminaire does not apply, if the mounting of luminaire has been performed in precipitation (rain, snow, hail). · The warranty of luminaire does not apply, if a control system unauthorized by VIZULO or an inapplicable LED driver has been used to drive the luminaire. · The warranty of luminaire does not apply, if it has been used in an unsuitable ambient temperature or has been supplied by voltage outside of the specified range. · The warranty of luminaire does not apply, if the LED driver program has been changed in any way. · The warranty of the luminaire does not apply, if the logged history data of the LED driver has been deleted without the permission of VIZULO. · The warranty of luminaire does not apply, if it has been mounted in unspecified angles or upside down (luminaire glass directed up), or it has been completely submerged under water.
Safety instructions
Any actions with the luminaire must be performed by a qualified person, who is certified according with national regulations and requirements. To prevent any accidents person installing the luminaire must follow national safety requirements and following instructions:
· The label containing technical parameters of the luminaire has to be studied before the work on it has begun. · Any luminaire build or design changes are prohibited. · The luminaire must be used in good technical condition and according with this instruction. · Only VIZULO authorized spare parts and accessories can be used to repair the luminaire. · The repair of luminaire has to be performed by a qualified and certified person.
Maintenance and repair
Luminaire has to be disconnected from electrical grid before it is opened and/or repaired! · The person working with the luminaire must follow national regulations and legislations that apply to maintenance and testing of electrical or electronic appliances. · The luminaire may need to be cleaned depending on its environment. Only a damp cloth or a sponge may be used to clean the luminaire. Use only household detergents diluted by water. · Only VIZULO authorized spare parts may be used for the luminaire. · Instruction for changing spare parts must be requested from VIZULO and studied before the repair is attempted. · LED modules, lens and LED drivers can be changed on an installed luminaire, but it is advised to perform this task indoor to avoid water entering the luminaire. · Spare parts (lens, LED modules and drivers) should be ordered from the information available on the luminaire label.
Ekspluatcijas uzsksana
Pirms gaismeka ieslgsanas, prbaudt t atbilstbu pareizai darbbai un veikt uzstdsanu atbilstosi ss montzas un ekspluatcijas instrukcijas un citiem piemrojamiem noteikumiem.
Montzas instrukcijas
Veicot gaismeka montzu, ir stingri jievro montzas instrukcij iekaut informcija un noteikumi: · Gaismeka garantija nav spk, ja gaismeki tiek montti nokrisu (lietus, sniega, krusas) laik. · Gaismeka garantija nav spk, ja tika izmantotas VIZULO neautoriztas vadbas sistmas vai tika izmantots neatbilstoss barosanas bloks. · Gaismeka garantija nav spk, ja tas tika ekspluatts neatbilstosos temperatras un elektrbas pieslguma apstkos. · Gaismeka garantija nav spk, ja ir veiktas barosanas bloku programmas iestatjumu izmaias vai t tikusi dzsta neinformjot VIZULO. · Gaismeka garantija nav spk, ja tikusi dzsti vai mainti barosanas bloka vstures ieraksti. · Gaismeka garantija nav spk, ja tas tika uzstdts un ekspluatts neatbilstosos montzas leos, tika uzstdts otrdi (ar stiklu uz augspusi) vai tika pilngi iegremdts den.
Drosbas instrukcijas
Darbam ar gaismekli drkst tikt pielaisti tikai atbilstosi apmcts un valsts tiesbu aktiem atbilstosi sertificts personls. Lai novrstu nelaimes gadjumu rasanos, ievrot valsts drosbas noteikumus un ss drosbas instrukcijas.
· Ir jiepazstas un jievro tehniskie parametri, kas ir nordti gaismeka marjum. · Ir aizliegts veikt gaismeka konstrukcijas un dizaina izmaias. · Gaismeklis ir jekspluat lab tehnisk stvokl un atbilstosi sm instrukcijm. · Gaismeka remontam ir atauts izmantot tikai VIZULO autoriztas detaas un piederumus. · Gaismeka remontu drkst veikt tikai atbilstosi apmcts un sertificts personls.
Apkope, apkalposana un remonts
Atvienojiet gaismekli no elektrotkla pirms t atvrsanas vai veicot remontu! · Ievrojiet nacionlos noteikumus un valsts tiesbu aktus, kas ir piemrojami elektrisko apartu uztursanai, apkalposanai un testsanai. · Atkarb no vides apstkiem gaismekli var bt nepieciesams trt. Trsanai izmantojiet tikai mitru lupatiu vai skli. Izmantojiet tikai ierasto sadzves mazgsanas sidrumu atsaidtu ar deni. · Izmantojiet tikai VIZULO autoriztas oriinls rezerves daas. · Lai kvalitatvi veiktu rezerves dau nomaiu, ir jpieprasa un jiepazstas ar VIZULO izstrdtm rezerves dau nomaias instrukcijm. · Gaismas diodes, lcas un barosanas bloki var tikt nomainti uz vietas, bet lai izvairtos no dens ieksanas to ir ieteicams veikt telps. · Ldzu pastt jaunu LED moduli, lcas vai barosanas bloku, izmantojot informciju gaismeka marjum.
6/6
Adobe PDF library 16.00 Adobe Illustrator(R) 24.0