Instruction Manual for CAL-ROYAL models including: N-98CVR, N-F98CVR, N-98CVR Concealed Vertical ROD Exit Device, N-98CVR Vertical ROD Exit Device, Concealed Vertical ROD Exit Device, Vertical ROD Exit Device, Vertical ROD, Exit Device

Layout1

N-98CVR Installation Instruction

Combinations: Cal-Royal N-98CVR/N-F98CVR Concealed Vertical Rod Exit Device, Optional-LBR,Finish-Satin Stainless Steel

INSTALLATION INSTRUCTION N-98CVR CONCEALED VERTICAL ROD EXIT DEVICE

• Google Docs
• Google Drive
• Download [pdf]
• Download Optimized



File Info : application/pdf, 4 Pages, 1.94MB

Document Document

INSTALLATION INSTRUCTION N-98CVR CONCEALED VERTICAL ROD EXIT DEVICE

TOP Strike Strike Screws Latch Screws
TOP Latch

End Cap Screws
Mounting Plate Bracket

End Cap

TOP Rod

Inner Chassis

U-Pin Connector fix plate
Screws Screws Main Chassis

Mounting Rail Push Rail

Rail Mounting Bracket Screw
Dogging Hex Key

Bottom Rod

Main Chassis Screws Head Cover Screws

Head Cover

Bottom Latch TO CHANGE BOTTOM LATCH FOR BOTTOM STRIKE

Latch Screws

1.Device factory pre-set.

21-U.nscerwandermovescerw andLs-hapedbarcke.t
2T2-.heLs-hapedbarcket movesbackwadr.

3M. ovheteLs-hapedbarcket bachokteA(sc)erwhoealnd aninsalotd.ltcki

Strike Screws
Bottom Strike

4. Change Done.

DRWG.# EDG-4016 20220826

1/4

Bernie T/Alex Go / Cris L

1.INSTALL INNER CHASSIS & TOP LATCH

1

2

TOP Latch

TOP Rod

5/32"-32 SCREWS (4pcs)
Inner Chassis

3
(TOP Latch must be under locked status during Step 3)

3-1 (Insert Ø4.0mm Pin) under Inner Chassis while in depressed status

3-2 (Keep the length of Top Rod Ass'y 3 to 5mm longer than upper door length)

3-3 Adjust Top Rod Ass'y length 3-4 Insert U-pin

M4 Screw

Install upper connector fix

4

plate

(Remove Ø4.0mm Pin)

5 Install latch screws
M5 Screw (8 pcs)
2/4

2.INSTALL BOTTOM LATCH (Skip this step if less Bottom Rod)
1 Attached Rod to Bottom latch

2 2-2
2-1 PUSH
(Bottom Latch must be under unlocked status during 2-2 installation)

2-3 (Keep the length of Bottom Rod Ass'y 3 to 5mm longer than upper door length)

2-5 Insert U-pin

2-4 Adjust Top Rod Ass'y length

3
(Remove Ø4.0mm Pin)

M4 Screw

4 Install latch screws

Install upper connector fix plate

M5 Screw (8 pcs)
3.INSTALL TOP & BOTTOMSTRIKE (Please Follow TEMPLATE)

1 TOP Strike

2 Bottom Strike

M5 Screw (3 pcs)

M5 Screw (3 pcs) Roller Strike
3/4

TO CHANGE HAND OF N-98CVR EXIT DEVICE

1. LHR

2-1. Remove chassis pin & main slide & tube.
2-2. Remove lift lever & lift lever pin.
2-3. Rotate 180° main slide & lift lever

main slide

lift lever

tube
fixed screw chassis pin

3-1. Reassemble lift lever at opposite side, as shown.
3-2. Replace main slide and chassis pin and lift lever pin. and fixed screw.

1. RHR Done.

lift lever pin

main slide

chassis

tube

pin

fixed screw

lift lever
lift lever pin

4/4