Anatel — Agência Nacional de TelecomunicaçõesDireitos do Consumidor — Agência Nacional de Telecomunicações
User Manual for LITE ON models including: NIULL, 2AIBX-NIULL, 2AIBXNIULL, NIUS 802.11 b g n 1T1R 2.4GHz Module, NIUS, 802.11 b g n 1T1R 2.4GHz Module, WN3602M-PLUS, NXP 88MW320
ELECTROLUX ITALIA S.p.A. NIULL NIUL 2AIBX-NIULL 2AIBXNIULL niull
File Info : application/pdf, 9 Pages, 563.59KB
DocumentDocumentUSER MANUAL 802.11 b/g/n, 1T1R 2.4GHz Module Model: NIUS WN3602M-PLUS (3.3V/5V) NXP 88MW320 Version 1.0 Page 1/9 2022/2/7 PRODUCT FEATURES IEEE 802.11b/g/n, 1×1 SISO 2.4 GHz Compact Form Factor: 30x17x1mm (PCB) ±0.1mm Integrated CPU, memory, MAC, DSSS/OFDM baseband, direct conversion RF radio, encryption CMOS and low-swing sine wave input clock Low-power with deep sleep and standby modes Integrated T/R switch, PA, and LNA HF/RoHS compliance PRODUCT SPECIFICATIONS MAIN CHIPSET NXP 88MW320-A0-NAPE/AZ FUNCTIONAL SPECIFICATIONS WiFi Function Standard IEEE802.11b; IEEE 802.11g; IEEE 802.11n Bus Interface UART Data Rate 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 7 Media Access Control CSMA/CA with ACK Modulation Techniques Network Architecture Operation Channel Frequency Range Transmit Output Power 1x1 (Tolerance: +-1.5dBm) 802.11b: CCK, DQPSK, DBPSK 802.11g: 64QAM, 16QAM, QPSK, BPSK 802.11n: BPSK, QPSK, 16QAM, 64QAM Ad-hoc mode (Peer-to-Peer) Infrastructure mode 2.4GHz 11: (Ch. 1-11) United States 13: (Ch. 1-13) Europe 14: (Ch. 1-14) Japan 802.11bg 2.412 ~ 2.462 GHz 802.11b: 11b(1M~11M) :16dBm 2022/2/7 Receive Sensitivity Security Operating Voltage Power Consumption (Average) Antenna Type 802.11g: 11g(6M~18M) :16dBm 11g(24~54M): 15dBm 802.11n: 11n(MCS0~MCS7) :13dBm 802.11b: (IEEE Standard <-76dBm) typical: -87.5dBM(1M) 802.11g: (IEEE Standard <-65dBm) Typical: -73dBm(54M) 802.11n: 20MHz (IEEE Standard <-64dBm) Typical: -71dBm WPA, WPA2, WPS, WEP 64/128, IEEE 802.11x, IEEE 802.11i 5V or 3.3V ±10% supply voltage 165mA@16dBm Printed Antenna 2022/2/7 PIN DEFINITION PIN Name 1 UART2_RX 2 UART0_RX 3 UART0_TX 4 5V 5 3.3V 6 GND 7 RESET 8 BOOT 9 GPIO10 10 GPIO9 11 GPIO8 12 GPIO7 13 GPIO6 14 UART1_RX 15 UART1_TX 16 UART2_TX Type I I O P P GND I I/O I I I/O I O I O O 5V Power in 3.3V Power in Ground IC Reset JTAG-TRST JTAG-TDI JTAG-TMS JTAG-CLK JTAG-TDO 2022/2/7 MECHANICAL WN3602M (3.3V) WN3602M (5V) Unit : mm ; Tolerance : +/- 0.1mm RECOMMEND FOOTPRINT Unit : mm 2022/2/7 ENVIRONMENTAL Operating Operating Temperature: 0 to 70 °C Relevant Humidity: 5-90% (non-condensing) Storage Temperature: -40 to 85 °C Relevant Humidity: 5-95% (non-condensing) 2022/2/7 WARNINGS FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1.L'appareil ne doit pas produire de brouillage; 2.L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ISED Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. The transmitter module may not be co-located with any other transmitter or antenna. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible. 2022/2/7 This module is intended for OEM integrators under the following conditions: 1. Ensure that the end-user has no manual instructions to remove or install module. 2.This module is certified pursuant to Part 15 rules section 15.247 and RSS-247. 3.This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna Frequency Band Antenna Type Brand Model Number Gain(dBi) 1 2400-2483.5MHz Printed Antenna LITEON WN3602M -0.9 4.Label and compliance information Label of the end product: FCC The host product must be labeled in a visible area with the following " Contains FCC ID: 2AIBX-NIULL". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ISED This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains transmitter module IC: 21700-NIULL" or "Contains IC: 21700-NIULL" Contient le module d'émission IC: 21700-NIULL 5.Information on test modes and additional testing requirements This module has been approved under stand-alone configuration. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093/RSS-102 and different antenna configurations The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04. OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/ISED authorization is no longer considered valid and the FCC/IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/ISED authorization. 6.Additional testing, Part 15 Subpart B and ICES-003 disclaimer Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer. This module is only FCC/ISED authorized for the specific rule parts 15.247, RSS-247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC/ISED rules that apply to the host product as being Part 15 Subpart B/ICES-003 compliant. 7.The user manual of the end product should include: FCC: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. 2022/2/7 ISED: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1.L'appareil ne doit pas produire de brouillage; 2.L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ISED Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. The transmitter module may not be co-located with any other transmitter or antenna. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible. NCC : 1. 2. 3.() CCXXXXLPYYYZZ WARNING BRAZIL: Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Para maiores informações, consulte o site da ANATEL www.anatel.gov.br") 2022/2/7