Installation Guide for SUNRICHER models including: DMX512, RJ45, 4CH DMX512 RJ45 DIN Rail Mountable DMX Decoder, DMX512 RJ45 DIN Rail Mountable DMX Decoder, RJ45 DIN Rail Mountable DMX Decoder, DIN Rail Mountable DMX Decoder, Rail Mountable DMX Decoder, Mountable DMX Decoder
2022-03-31 — RDM function enabled DMX decoder. • Digital display to show data directly, easily to set and show DMX address and DMX channel.
U4 lCtrHa-DPMroX45C1H2 RRJD4M5 DDMINXR51a2il DMeocuondtearble DMX Decoder09.218RD.04744
Important: Read All Instructions Prior to Installation
Function introduction
RJ45 terminal
DMX512 input & output
Pin1:Data+ / Pin2:Data- /
Pin7:GND / Pin8:GND
87654321
DC Power input
Wiring Diagram
DMX512 Master
87654321 87654321
DMX512 & RDM Decoder
Pin1:Data+ Pin2:DataPin7:GND Pin8:GND
V+ VDC INPUT
Back Enter
Up
Down
LED OUTPUT W- B- G- R-
DC INPUT + V+ V-
Digital display Manual set button
87654321 87654321
DMX512 & RDM Decoder
Pin1:Data+ Pin2:DataPin7:GND Pin8:GND
V+ VDC INPUT
Back Enter
Up
Down
LED OUTPUT W- B- G- R-
DC INPUT + V+ V-
CH 4 output(-) CH 3 output(-)
CH 2 output(-) CH 1 output(-) Common Anode Output(+)
Product Data
No.
Input Voltage
1 12-36VDC
2 12-48VDC
3 12-48VDC
Output Current
Output Power
Remarks
Size(LxWxH)
4x5A 4x(60-180)W Constant voltage 110x53x65mm
4x350mA 4x(4.2-16.8)W Constant current 110x53x65mm
4x700mA 4x(8.4-33.6)W Constant current 110x53x65mm
DC Power input
· RDM function enabled DMX decoder · Digital display to show data directly, easily to set and show DMX address and DMX channel · PWM output resolution ratio 8bit , 16bit settable · Output PWM frequency from 500HZ ~ 30K HZ settable · Output dimming curve gamma value from 0.1 ~ 9.9 settable · Decoding mode settable · DIN rail controller
Safety & Warnings
· DO NOT install with power applied to device. · DO NOT expose the device to moisture.
W- B- GW- B- G-
R- V+ R- V+
If connect With RGBW color lighting
OUTPUT
L
INPUT
V+
12V/24V/36V
V-
CV PSU
N G
AC Power 50/60Hz
87654321 87654321
87654321 87654321
DMX512 & RDM Decoder
Pin1:Data+ Pin2:DataPin7:GND Pin8:GND
V+ VDC INPUT
Back Enter
Up
Down
LED OUTPUT W- B- G- R-
DC INPUT + V+ V-
DMX512 & RDM Decoder
Pin1:Data+ Pin2:DataPin7:GND Pin8:GND
V+ VDC INPUT
Back Enter
Up
Down
LED OUTPUT W- B- G- R-
DC INPUT + V+ V-
V- V+ V- V+
CW- WW- V+ CW- WW- V+
If connect With single color lighting
If connect With dual color lighting
Button introduction Up, Down button is for menu selection.After power on the decoder, if keep on clicking Up button, you will find below menu on display:
DMX signal indicator :: When DMX signal input is detected, the indicator on
the display following after turns on red XXX .
XXX Means DMX address. fa ctory defaults setting is 001.
XX Means DMX channels quantity.
Back Enter Up Down
XX Means Bit (8bit or 16bit). factory defaults setting is 16bit
XX Means output PWM frequency. factory defaults setting is 1K HZ
XX Means output dimming curve gamma value, factory defaults setting is ga 1.5
XX Means Decoding mode, factory defaults setting is dp1.1
By holding button Back + Enter together at the same time over 5 seconds until the display go off, it will restore default settings .
1. DMX address setting:
select menu XXX , click button "Enter", display flashes,then click or hold button "Up" / "Down"
to set DMX address (click is slow, hold is fast.), then click button"Back" to confirm.
2. DMX channel quantity setting:
Select menu
XX , click button "Enter", display flashes, then click button "Up" / "Down"
to set DMX channel quantity , then click button"Back" to confirm.
For example the DMX address is already set 001.
CH01=1 DMX address for all the output channels, which are all address 001.
CH02=2 DMX addresses , output 1&3 is address 001, output 2,4 is address 002
CH03=3 DMX addresses, output 1, 2 is address 001,002, output 3,4 is address 003
CH04=4 DMX addresses, output 1,2,3,4 is address 001,002,003,004
DMX address is 001, CH01
DMX Console Slider number
dp1.1
DMX channel
1
for all output dimming
2
No use
dp2.1
for all output dimming for all output micro dimming
DMX address is 001, CH02
DMX Console Slider number
dp1.1
DMX channel
1
for output 1&3 dimming
2
for output 2,4 dimming
3
4
dp2.1
for output 1&3 dimming
for output 1&3 micro dimming
for output 2,4 dimming
for output 2,4 micro dimming
dp3.2
for output 1&3 dimming for output 2,4 dimming
for all output dimming
DMX address is 001, CH03
DMX Console Slider number
dp1.1
DMX channel
1
for output 1 dimming
2
for output 2 dimming
3
for output 3,4 dimming
4
5
6
dp2.1
for output 1 dimming
for output 1 micro dimming
for output 2 dimming
for output 2 micro dimming
for output 3,4 dimming
for output 3,4 micro dimming
dp4.3
dp5.3
for output 1 dimming
for output 2 dimming
for output 3,4 dimming
for all output master dimming
for output 1 dimming
for output 2 dimming
for output 3,4 dimming
for all output master dimming
strobe effects
DMX address is 001, CH04
DMX Console Slider number
dp1.1
DMX channel
1
for output 1 dimming
2
for output 2 dimming
3
for output 3 dimming
4
for output 4 dimming
5
6
7
8
3. PWM output resolution Bit setting:
select menu
XX , click button "Enter",display flashes, then click button "Up" / "Down"
to choose 08 or 16 bit, then click button"Back" to confirm.
4. output PWM frequency setting:
select menu
XX , click button "Enter", display flashes,then click button "Up" / "Down"to choose 00~30,
then click button"Back" to confirm. 00=500HZ, 01=1kHZ, 02=2kHZ.....30=30kHZ.
5. output dimming curve gamma value setting:
select menu
XX , click button "Enter", display flashes, then click or hold button "Up" / "Down"
to choose 0.1~9.9, then click button"Back" to confirm.
output brightness level
1.0
0.8
6.5
3.5
0.9 2.5
1.5
gamma value
<1
>1
DMX value level
6. DMX decoding mode setting:
Select menu
XX , click button "Enter", display flashes, then click or hold button "Up" / "Down"
to choose the decoding mode, then click button"Back" to confirm. "dPxx" means the DMX address quantity
used for control of corresponding PWM output channel quantity. 1st "x" is DMX address quantity, 2nd "x" is
PWM channel quantity.
Micro dimming: the micro dimming effect can only be visible when the dimming curve gamma value is set lower than 1.4, and the lower the value is, the more visible the micro dimming effect will be.
The data definitions for strobe channel are as follows:
{0, 7},//undefined {8, 65},//slow strobe-->fast strobe {66, 71},//undefined {72, 127},//slow push fast close {128, 133},//undefined {134, 189},//slow close fast push {190, 195},//undefined {196, 250},//random strobe {251, 255},//undefined
The supported RDM PIDs are as follows:
DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO DMX_START_ADDRESS IDENTIFY_DEVICE SOFTWARE_VERSION_LABEL DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION SLOT_INFO SLOT_DESCRIPTION MANUFACTURER_LABEL SUPPORTED_PARAMETERS
dp2.1
dp5.4
dp6.4
for output 1 dimming
for output 1 micro dimming
for output 2 dimming
for output 2 micro dimming
for output 3 dimming
for output 3 micro dimming
for output 4 dimming
for output 4 micro dimming
for output 1 dimming
for output 1 dimming
for output 2 dimming
for output 2 dimming
for output 3 dimming
for output 3 dimming
for output 4 dimming
for output 4 dimming
for all output
for all output
master dimming master dimming
strobe effects
Restore to Factory Default Setting
Press and hold down both "Back" and "Enter" keys until the digital display turns off, then release the keys, system will reset and the digital display will turn on again, all settings will be restored to factory default. Default settings are as follows: DMX Address Code: a001 DMX Address Quantity: SW1=0: ch04, SW1=1: ch03 PWM Resolution Mode: bt16 PWM Frequency: pf01 Gamma: ga1.5 Decoding Mode: dp1.1
Adobe PDF library 16.03