TP-Link Tapo Outdoor Pan/Tilt Security Wi-Fi Camera

1. Before You Start

Separate the mounting bracket from the camera base before you start.

Bracket Base

2. Set Up Your Camera

1. Download the App

   Download the Tapo app from the App Store or Google Play. Open the app and log in with your TP-Link ID. If you don't have an account, create one first.

   Download on the App Store

   GET IT ON Google Play

2. Power Up

   Plug in the adapter to power up your camera.

3. Set Up

   Tap the "+" button > Add Device in the app and select your model. Follow the app instructions to set up your camera.

3. Mount Your Camera

Option 1: Wall Mount

1. Drill Holes

   The mounting distance from the side wall should be greater than 70 cm (2.3 ft) to allow enough space for tightening the side bracket screws.

   Stick the mounting template for the wall mount to the desired place. Drill four screw holes according to the mounting template. (Diameter = 6 mm / 15/64 in.)

2. Install the Bracket

   Insert four anchors into the holes and use the screws to affix the bracket over the anchors.

3. Route the Cable

   Route the cable through one of the base's three notches according to the direction of your power outlet.

   The bracket design allows you to route the cable through the hole in the wall to prevent the cable and the hole from exposing to the outside.

4. Secure the Camera
   1. Align and slide the camera base onto the bracket from the outside in.
   2. Use two bracket screws to affix the bracket and camera base.

Option 2: Eave Mount

1. Drill Holes

   Stick the mounting template for the eave mount to the desired place. Drill two screw holes according to the template. (Diameter = 6 mm / 15/64 in.)

2. Install the Bracket

   Insert two anchors into the holes and use the screws to affix the bracket over the anchors.

3. Route the Cable

   Route the cable through one of the base's three notches according to the direction of your power outlet.

4. Secure the Camera
   1. Align and slide the camera base onto the bracket from the outside in.
   2. Use two bracket screws to affix the bracket and camera base.

Option 3: Pole Mount

1. Install the Bracket

   Mount the bracket on the pole using one pole-mounting loop* (loop width ≤ 12 mm). (*Pole-mounting Loop not included)

2. Route the Cable

   Route the cable through one of the base's three notches according to the direction of your power outlet.

3. Secure the Camera
   1. Align and slide the camera base onto the bracket from the outside in.
   2. Use two bracket screws to affix the bracket and camera base.

4. Install Waterproof Accessories

1. Install the Waterproof Seal for Power Connectors

   Install the waterproof seal for the power connectors.

   Male Power Connector, Waterproof Seal, Female Power Connector

2. Install Waterproof Cable Attachments

   Install the waterproof cable attachments for the network interface. Make sure each part is securely attached and the waterproof rings are flush to keep out water.

   When the Ethernet port connects to a network device

   1) Route the network cable through the following components in order: fix nut, waterproof ring, and then the waterproof jacket.

   2) Insert the waterproof ring into the waterproof jacket.

   3) Fix the O-ring to the network interface of the camera and connect the network cables.

   4) Attach the network interface with the waterproof jacket, then twist to lock. Rotate the fix nut to secure it to the waterproof jacket.

   When the Ethernet port does not connect to a network device

   1) Insert the waterproof plug into the waterproof ring, then insert them into the waterproof jacket.

   2) Fix the O-ring to the network interface of the camera. Attach the network interface with the waterproof jacket, then twist to lock. Rotate the fix nut to secure it to the waterproof jacket.

   Fix Nut, Waterproof Ring, Waterproof Jacket, O-ring, Network Interface, Waterproof Plug

Appearance

• 1 IR LED
• 2 White Light LED
• 3 Lens
• 4 System LED
• 5 Microphone
• 6 Speaker
• 7 microSD Card Slot
• 8 Silicone Cover
• 9 Reset Button
• 10 Ethernet Port
• 11 DC Power Connector

System LED Indication

Button Explanation

RESET Button: Open the silicone cover. While the camera is powered on, press and hold the RESET button to reset the camera.

• Press and hold for 5 seconds: Reset Wi-Fi settings only
• Press and hold for 10 seconds: Reset to factory settings

microSD Card Slot: Open the silicone cover and insert a microSD card.* Initialize it on the Tapo app for local recording. (*microSD card not included.)

FAQ (Frequently Asked Questions)

What should I do if I fail to configure Tapo Camera?

Visit https://www.tp-link.com/support/faq/2747/ for detailed instructions.

What should I do if the SD card is not working properly?

• Make sure you are using a microSD card.
• It's recommended to use a Class 10 microSD card or higher, with storage from 8 GB to 512 GB.
• Make sure you have initialized the microSD card in the Tapo app.
• If the problem still persists, contact TP-Link technical support.

How do I reset the camera?

• With the camera powered on, press and hold the Reset button for about 5s until the System LED blinks red quickly to reset the Wi-Fi while keeping other settings; for 10s to factory reset the camera.
• Open the Tapo app, go to the Camera Settings page, and remove the camera to factory reset it.

For more questions, please refer to https://www.tp-link.com/support/faq/2742/

Need some help? Visit https://www.tapo.com/support/ for technical support, the user guide, FAQS, warranty & more.

Safety Information

• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended by TP-Link.
• Do not use the device where wireless devices are not allowed.
• Adapter shall be easily accessible.
• Use only power supplies which are provided by TP-Link and in the original packing of this product. If you have any questions, please don't hesitate to contact TP-Link.
• Keep the device away from fire or hot environments. Do not immerse in water or any other liquid.
• Do not disassemble, repair or modify the product.
• Do not use the product if the casing has been broken. Danger of electric shock.
• Never touch the product with wet hands.
• Do not place near automatically controlled devices such as fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident.
• Observe restrictions on using wireless products in fuel depots, chemical plants or when blasting operations are in progress.
• Do not use liquid to clean the product. Only use a dry cloth.
• Never put metal objects inside the product. If a metal object enters the product turn off the circuit breaker and contact an authorised electrician.
• This product is not intended to be used when providing medical care. Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids to determine if they are adequately shielded from external RF (radio frequency) energy.
• Do not use this product in health care facilities. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.
• Do not place heavy objects on top of the product.
• When you leave the product unused for a long time unplug the product from the power outlet.
• This product may interfere with other electronic products such as TV, radios, personal computers, phones or other wireless devices.
• Adapter should be used indoors where the ambient temperature is lower than or equal to 40 °C.
• Operating Temperature: -30 °C ~ 60 °C (-22 °F ~ 140 °F)

TP-Link hereby declares that the Outdoor Pan/Tilt Security Wi-Fi Camera is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tapo.com/support/ce

TP-Link hereby declares that the Outdoor Pan/Tilt Security Wi-Fi Camera is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK declaration of conformity may be found at https://www.tapo.com/support/ukca/

©2025 TP-Link