Jademar JEM-30W/40W/60W Emergency Battery Pack Remote Control Instructions

Product Description

This remote control utilizes infrared signal transmission. Ensure the target sensor is in view and maintain a controlling distance within 18 meters for optimal operation.

Strong natural light brightness may affect the infrared signal, potentially reducing the control distance or causing malfunctions. To mitigate this, shorten the distance to the sensor or use the remote when natural light is less intense.

The LCD screen requires activation by pressing any button after it has gone dark.

The remote is powered by 2 AAA batteries. If the LCD screen displays incomplete or unclear text, the batteries may be low and require replacement to ensure proper remote performance.

Features

Working Voltage: AAA battery * 2pcs (2.2-3V)
Screen OFF Duration: 60S
Icon Flicking Duration: 5S
Start (S) Button ON Duration: 10S
Memory (M) Button Flicking Duration: 3S
Carrier Frequency: 38KHz±2KHz
Operation Distance: Max. 15M/49ft (at 3V)
Emission Angle: < 30 degrees
Standby Current: <1.2uA
Working Current: <5mA
Peak Current: <30mA
Working Temp: -20°C to +60°C
Storage Temp: -30°C to +85°C

Product Dimension

Height: 147mm (5.78")

Width: 65mm (2.55")

Depth: 20mm (0.78")

Display Area Height: 25.2mm (0.99")

Base Width: 68.8mm (2.7")

Operation Guide

1. Setting Multiple Sensors to the Same Parameters

Solution A: For the first sensor, press AUTO to enter SENSOR mode. Set parameters (detection area, hold time, daylight threshold, standby dimming level, and standby period) using the relevant buttons. Press MEMORY to save the parameters, then press APPLY to send them to the sensors. A brief light OFF-ON sequence indicates successful command reception.

For subsequent sensors, press AUTO to enter SENSOR mode and then press APPLY to send the saved parameters. A light OFF-ON sequence confirms reception.

Solution B: Utilize the SCENE function for preset parameters. Press AUTO to enter SENSOR mode, select a scene (1, 2, 3, or 4), and press SEND. A light OFF-ON sequence confirms reception.

2. Turning Off Sensor Function (Disabling Sensor Mode)

When the light is ON, press ON/OFF to turn it off. Press ON/OFF again to turn it on. Do not press any other buttons.

When the light is OFF, press ON/OFF to turn it on. Do not press any other buttons.

3. Performing SENSOR Mode When Sensors are in ON/OFF Mode

Solution A: Press AUTO to enter SENSOR mode and apply the last saved parameters. The corresponding parameters will be displayed on the LCD screen.

Solution B: Press RESET to enter SENSOR mode and apply factory default parameters. The corresponding parameters will be displayed on the LCD screen.

4. Entering and Exiting TEST Mode

To Enter: In any mode, press the TEST button. The sensor will enter TEST mode, keeping the light ON for 2 seconds, then turning OFF. It will then turn ON again after detecting motion for 2 seconds, repeating this cycle.

To Exit: Press the ON/OFF button to turn off the light and exit TEST mode immediately. Alternatively, press the RESET button to exit TEST mode and enter SENSOR mode with factory settings. Pressing the AUTO button also exits TEST mode and enters SENSOR mode with the last saved parameters.

JHD06R Instructional Manual Table

Button	Description
ON/OFF	1. Turn On or Off light. 2. Exit sensor mode and enter into ON/OFF mode.
Scenes	Press the button to choose from 4 optional scenes; parameters can be saved into each scene and directly activated.
Apply	Press the button to deliver the saved parameters to target sensors.
Detection range	Press the button; the icon will flicker on the LCD screen display. Use +/- buttons to choose the desired parameters.
Hold time	Press the button; the icon will flicker on the LCD screen display. Use +/- buttons to choose the desired hold time.
CCT	(Only supporting sensors with CCT tunable feature) Press the button; the icon will flicker on the LCD screen display. Use +/- buttons to choose from saved CCT options (2700K, 3500K, 4000K, 5000K, 5700K, 6500K).
Reserved	This is a reserved button for future updates with unexpected features.
Auto	Press this button to enter sensor mode and perform the last parameter. Pressing this button will show "Auto Mode" on the LCD screen, indicating successful command reception.
Start	Press the button to begin programming. The 'S' icon will appear on the LCD screen and disappear if no action is taken within 10 seconds. Press again if needed.
Mounting Height	Press the button to adjust sensitivity based on the installation height, ensuring optimal sensor performance in the environment.
Daylight sensor	Press the button; the icon will flicker on the LCD screen display. Use +/- buttons to choose the desired daylight level. The maximum level is 400lux. 'DIASBLE' means disable, 'LEN' means learning ambient brightness.
UP	Press the button; numbers on the LCD screen display increase to the desired value.
DOWN	Press the button; numbers on the LCD screen display decrease to the desired value.
Daylight Harvesting	Adjust parameters according to daylight harvesting conditions, then press this button to activate the function. "DH-ON" will be displayed on the LCD screen.
Reset	Press the button to enter factory settings. The sensor will start to detect motion and turn on the light automatically, keeping a 5S hold time before turning off.
Memory	Press the button to save parameters. The 'M' icon will appear on the LCD screen, indicating successful parameter saving.
Send	Press the button to deliver the last parameters, instead of using "START-MEMORY-APPLY".
Stand-by dimming	Press the button; the icon will flicker on the LCD screen display. Use +/- buttons to choose the desired standby dim level.
Stand-by period	Press the button; the icon will flicker on the LCD screen display. Use +/- buttons to choose the desired standby period. Minimum is 0S, maximum is infinite.
POWER	Press the button; the icon will flicker on the LCD screen display. Use +/- buttons to choose the desired brightness level. In ON/OFF mode, output dimming range is 10%-100%. In SENSOR mode, output dimming range is 60%-100%.
Test	Press the button to quickly perform the testing function. The light stays ON for 2S, then turns OFF. It turns ON again upon motion detection, repeating this cycle.

For quotations: quotes@jademar.com

To place an order: orders@jademar.com

Tel: (305) 640.0465 | Fax: (305) 640.0468

WWW.JADEMAR.COM

Information contained herein is subject to change without notice. Revised 09/2024