Instruction Manual for HIOS models including: CLC-45, CLC-60, CLC-80, CLC Series DC Screwdrivers Controller, CLC Series, DC Screwdrivers Controller, Screwdrivers Controller, Controller
5 days ago — INSTRUCTIONS. Selection of Power Supply Cord: Use in U.S.A. - Use UL Listed detachable power supply cord, No.18AWG,3 conductors, flexible cord, rated 10A, VW ...
For DC Screwdrivers Controller CLC-45 / CLC-60 / CLC-80 JP EN Operation Manual ROTATION 2 POWER I ON 1 OFF ROTATION 2 POWER I ON 1 OFF WT-A016 24A JP 5 2 1.8m 2P 1 AC100V CLC-45 CLC-45 1 1 CLC-60/CLC-80 2 4 JP CLC-60 CLC-80 1 2 3 2 1 4 5 ROTATION 2 POWER I ON 1 OFF ROTATION POWER I ON O OFF 1POWER 2 32HIDC30V1LOWDC20V 4 5 3 OPC/SS CLC-45 CL SS JP CL-2000CL-3000CL-4000CL-6000CL-6500 SS-2000SS-3000SS-4000SS-6500 -4500-5000 CLC-60 CL SS CL-2000CL-3000CL-4000CL-6000CL-6500CL-7000 SS-2000SS-3000SS-4000SS-6500SS-7000 -4500-5000-6500 CLC-80 CL CL-9000NL 4 CLC-45 CLC-60 CLC-80 JP 5 CLC-45 CLC-60 AC100-240V47-63Hz 45-78VA 40-65VA 3.15A/250V 5A/250V HI 2DC30VLOW1DC20V2 JP 146mm 210mm 71.5mm 88mm 42.6mm 52mm 330g 715g 1 CLC-80 AC100-240V47-63Hz T5A/250V HI 2DC30VLOW1DC20V2 210mm 116mm 60mm 6 1.4kg 1 Important Safety Instructions Before using this machine, read this section and follow the instructions to properly use this machine. Installation The unit should be used in a temperature and humidity-controlled room. Keep the unit away from a place with poor ventilation, in dust or metal pieces. Do not place any objects on the unit. The place to install the unit should be vibration-free and the unit should be securely fixed. If the unit is installed on the wall or on a high place, make sure to use the attached Mounting Bracket to fix it securely. Do not install the unit close to high voltage equipments. Handling EN Install a leakage breaker and safety breaker on the input power source and connect the ground to use the unit. Connect to a power source of the specified voltage. Do not use with other drivers or devices except the models listed in this operation manual. If the protection circuit works due to overheat, stop operation immediately, pull the power plug from the outlet and send it back to your HIOS distributor for repair. The unit may automatically stop in use when the protection circuit works due to overcurrent, etc. Turn off the power switch once and turn it on in 5 seconds for restart. If the unit stops while in screw fastening, make sure to check the torque of the fastened screw. Do not disassemble or modify the unit. Do not drop the power Supply or subject it to violent impact. Do not drag the unit by its driver cord or AC cord. Keep the cords away from foreign objects, oil or something sharp. Make sure to grasp the plug section to disconnect the AC cord from the outlet. Turn the unit off and disconnect the AC cord from the outlet when the unit is not in use. IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. CAREFULLY FOLLOW THESE INSTRUCTIONS. Selection of Power Supply Cord: Use in U.S.A. - Use UL Listed detachable power supply cord, No.18AWG,3 conductors, flexible cord, rated 10A, VW-1, 80°C, minimum 1.8 m, maximum 3 m long. Provided with a molded-on, non-polarized attachment plug with a 15A, 125V (NEMA5-15P) or 15A, 250 V (NEMA 6-15P) configuration and a molded-on connector which mates with the Power Inlet. The following flexible cord type may be used: S, SE, SO, SP-3, SPT-3, ST,STO, SJ, SJE, SJO, SJT, SJTO, SP-2, SPE-2, SPT-2, SV, SVE, SVT. Use in countries other than U.S.A. - Use IEC60227 certified PVC flexible power supply cord, marked H03VVF or H05VVF, 3C x 0.75 mm2, rated min. 10A, 250V 7 Accessories CLC-45 CLC-60/CLC-80 Mounting Bracket 1pc 2pcs Screw 1pc 4pcs AC Cord (1.8m) Parts and Their Functions EN CLC-45 CLC-60 CLC-80 Front Side Back Side 1 2 3 2 1 4 5 ROTATION 2 POWER I ON 1 OFF ROTATION POWER I ON O OFF 1Power Indicator: Lights up when the power switch is turned ON. 2Connector for the Screwdriver: Connect the screwdriver cord. 3DC Output Switch: 2 (HI: DC30V)/ 1 (LOW: DC20V) 4Power Switch: Turns the power ON or OFF. 5Connector for AC Cord: Connect the power cord. 8 Compatible Screwdrivers (Including OPC/SS Type) CLC-45 Series CL SS Model CL-2000/CL-3000/CL-4000/CL-6000/CL-6500 SS-2000/SS-3000/SS-4000/SS-6500 -4500/-5000 CLC-60 EN Series Model CL CL-2000/CL-3000/CL-4000/CL-6000/CL-6500/CL-7000 SS SS-2000/SS-3000/SS-4000/SS-6500/SS-7000 -4500/-5000/-6500 CLC-80 Series CL Model CL-9000NL 9 Attach the Mounting Bracket Make sure to use the attached Mounting Bracket and the screw to fix the unit securely if you install it on the work table, the wall, etc. CLC-45 CLC-60 CLC-80 EN Example 10 Specifications Model Name Input Voltage Primary Side Power Consumption Secondary Output Voltage CLC-45 CLC-60 AC100-240V (47-63Hz) 45-78VA Fuse capacity: 3.15A/250V (Built-in) 40-65VA Fuse capacity: 5A/250V (Built-in) HI(2): DC30V / LOW(1): DC20V (2-step switchable) 146mm 210mm EN 71.5mm 88mm External Dimensions 42.6mm 52mm Weight Number of Connectable Screwdrivers 330g 1 unit 715g Model Name Input Voltage Primary Side Power Consumption Secondary Output Voltage CLC-80 AC100-240V (47-63Hz) T5A/250V HI(2): DC30V / LOW(1): DC20V (2-step switchable) External Dimensions 116mm 210mm 60mm Weight Number of Connectable Screwdrivers 1.4kg 1 unit 11 1-35-1 HIOS Inc. 1-35-1 Oshiage, Sumida-ku Tokyo, JapanAdobe PDF Library 16.0.7 Adobe InDesign 17.3 (Windows)