Installation Guide

Tools Required

• LPS-A6 power supply kit
• Eversolo DMP-A6 / DMP-A6 Master Edition
• Phillips screwdriver
• Allen key 2.0mm

A visual representation shows the Eversolo DMP-A6 unit alongside the LPS-A6 power supply module (blue transformer and black PCB), a Phillips screwdriver, and an Allen key, indicating the components and tools needed for the installation.

Installation Steps

Step 1: Unscrew Rear and Underside Panels

Use a 2.0mm Allen key to unscrew 6 screws on the rear panel and 7 screws on the underside of the Eversolo unit. A total of 13 screws need to be removed. Diagrams illustrate the locations of these screws on both the rear and bottom of the device, highlighted with red circles.

Step 2: Gently Slide Device Cover

Gently slide the device cover outwards by approximately 20mm. Exercise caution as two internal webs connect the screen to the motherboard. Avoid using excessive force. A visual shows the cover partially slid open, with an arrow indicating the sliding direction.

Step 3: Lift and Tilt Cover

Carefully lift and tilt the cover. Be aware that cables remain attached to the cover, screen, and motherboard; do not disconnect them. An arrow indicates the upward tilting motion of the cover.

Step 4: Identify Switch Mode Power Supply (SMPS)

Locate the existing switch mode power supply (SMPS) within the DMP-A6 unit. A red arrow points to the rectangular black power supply module inside the device.

Step 5: Disconnect Jumper Cable

Disconnect the jumper cable from the SMPS. This is a latched connector; press the central part to unlock it, then gently pull it upwards. Images show a hand disconnecting the cable, highlighting the latched connector.

Step 6: Remove SMPS Securing Screws

Use a Phillips screwdriver to remove the 6 screws that secure the existing switching power supply module. The screws are circled in red in the diagram, and a pile of removed screws is shown.

Step 7: Remove SMPS and Prepare LPS-A6

Remove the switching power supply module from the DMP-A6 chassis. Prepare the new LPS-A6 module for installation. Images show the removal of the old module and the new LPS-A6 module ready for placement.

Step 8: Locate and Place Insulation Rings

Find the four insulation rings. Place these rings onto the PCB spacers within the DMP-A6 chassis. Diagrams show the placement of these rings using tweezers, highlighted with red circles.

Step 9: Install LPS-A6 Module

Install the LPS-A6 module by carefully placing it onto the four isolation rings. Ensure the LPS-A6 is correctly aligned with the spacers. If the rings shift slightly, use the 2.0mm Allen key to help align them. A red arrow indicates the placement of the LPS-A6 module.

Step 10: Secure LPS-A6 Module

Use the existing screws to secure the LPS-A6 module to the chassis. Tighten four screws using a Phillips screwdriver. There will be two surplus screws; store them in a safe place. Red circles indicate the screw locations.

Step 11: Install Silver-Plated Cable

Install the silver-plated cable. Firmly plug the connectors into their respective sockets. Images show a hand plugging in the cable, with the connection point highlighted by a red circle.

Step 12: Close and Tilt Cover Downwards

Close the device by gently tilting the cover downwards. Remember that the cables are still attached to the cover screen and the motherboard; do not disconnect them. An arrow indicates the downward tilting motion of the cover.

Step 13: Slide Cover Inwards and Secure

Gently slide the cover inwards until it is fully closed. Secure the cover to the rear and bottom panels by tightening the 6 screws on the rear panel and the 7 screws on the underside of the unit using the 2.0mm Allen key. An arrow indicates the sliding direction of the cover.