Hampton Bay Wickford 1-Light Outdoor Pendant Use and Care Guide

Thank You

We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this light fixture. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Hampton Bay!

Table of Contents

• Safety Information
• Warranty
• Pre-Installation
  • Planning Installation
  • Tools Required
• Hardware Included
• Package Contents
• Installation
• Operation
• Care and Cleaning
• Troubleshooting

Safety Information

• Consult a qualified electrician if you have any electrical questions.

⚠️ CAUTION: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation. Please call our Customer Service Team at 1-855-HD-HAMPTON.

⚠️ WARNING: Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.

Warranty

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.hamptonbay.com.

Pre-Installation

Planning Installation

• Read all instructions before installation.
• To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard.
• Keep your receipt and these instructions for proof of purchase.

Tools Required

[ladder] Ladder, [safety glasses] Safety glasses, [electrical tape] Electrical tape, [Phillips screwdriver] Phillips screwdriver, [flat blade screwdriver] Flat blade screwdriver, [pliers] Pliers, [wire strippers] Wire strippers

Hardware Included

NOTE: Hardware not shown to actual size.

Package Contents

The package contains the following parts:

• A: Light fixture
• B: Canopy
• C: Chain (with quick connector)

Diagram Description: Part A shows the main light fixture, a decorative lantern-style pendant. Part B shows the circular ceiling canopy. Part C shows a metal chain with a quick connector for adjusting the hanging height.

Installation

Step 1: Secure the light fixture

1. Attach the mounting unit (AA) to the junction box (not included) with the mounting screws (BB) and remove the pre-installed screw collar ring.
2. Place the canopy (B) over the pre-installed screw collar loop on the mounting unit (AA). Turn the screw collar ring until 1/2 of the screw collar loop threads are exposed.
3. Secure the chain (C) to the screw collar loop on the mounting unit (AA) and the top loop of the light fixture (A).
4. Lower the screw collar ring and canopy (B) over the chain (C).
5. Weave the electrical wires, ground wires through the chain (C), canopy (B) and the center of the mounting unit (AA).

NOTE: Ensure the quick connector is fully closed when installing the chain.

Diagram Description: Illustrates the process of attaching the mounting unit (AA) to the junction box, then placing the canopy (B) and securing the chain (C) to the fixture (A) and mounting unit. Shows wires being threaded through the chain and canopy.

Step 2: Making the electrical connections

1. Connect the copper wire from the light fixture (A) to the mounting unit (AA) by securing it with the preinstalled ground screw.
2. Connect the black to black (power), the white to white (neutral) and copper wire to ground wire with the wire nuts (CC) and secure with electrical tape (not included).

NOTE: If the wires from the fixture are the same color, attach the smooth wire with H markings or letters to the black (positive) wire and the ribbed wire with N markings or letters to the white (neutral) wire.

Diagram Description: Shows the electrical wires being connected using wire nuts (CC). Depicts connecting the ground wire (copper), power wire (black), and neutral wire (white) between the fixture and the house wiring.

Step 3: Securing the light fixture

1. Secure the canopy (B) to the mounting unit (AA) with the screw collar ring. (Note: The diagram labels the canopy 'D', but text refers to it as 'B').

Diagram Description: Shows the canopy (labeled D in diagram, referring to part B) being secured to the mounting unit (AA) using the screw collar ring.

Step 4: Installing the light bulb

1. Install one E26 100-watt bulb (not included).

Diagram Description: Shows a standard E26 light bulb being screwed into the socket of the light fixture (labeled A).

Operation

1. Turning the Light On

1. Turn the light switch on to activate the fixture.

Care and Cleaning

• Clean the lamp with a soft, dry cloth.
• Do not use any cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting