Installation Guide for Lowes models including: H512906-AI Two Light Linear, H512906-AI, Two Light Linear, Light Linear
21 час назад — 2. Make sure that the ceiling or wall can stand the weight of the lamp before installation. 3. Make sure the voltage you are using is 120V.
19 hours ago — Please read the instruction carefully and save it as you may need it at a later time. ... The safety instructions appearing in this manual are not meant to cover ...
Item Number: 6641218 WARNING (To reduce the risk of fire, electric shock, or personal i1n.juWrey)s:uggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at a later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the "OFF" position. » Place the wall switch in the "OFF" position. 1. Mounting surface should be clean, dry, flat, strong enough and 1/4" larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16" should be corrected as required. 2. Make sure that the ceiling or wall can stand the weight of the lamp before installation. 3. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb. 4. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp. 5. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly. 6. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products. IMAGE FOR FINISHED PRODUCT: TOOLS REQUIRED Before starting assembly and installation please prepare the needed (NOT INCLUDED): tools as below picture Ladder Philips Head or Flat Blade Screwdriver Electrical Tape Pliers Wire Cutter/Stripper Page: 1 / 4 PARTS TYPE & QTY INCLUDED: (C) Mounting plate (1) (D) Green ground screw (1) (E) Canopy (1) (F) Swivel joint (1) (G) Canopy nut (2) (H) Tube (I) Connector (1) (J) Arm (8) (K) Socket (8) ACCESSORIES & QTY ENCLOSED: (A) Plastic wire connector (3) (B) Mounting screw (2) ASSEMBLY & INSTALLATION INSTRUCTIONS: 1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration. 2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the "OFF" position. » Place the wall switch in the "OFF" position. 3 » Unscrew canopy nuts (G) from canopy (E). Remove the mounting plate (C). Page: 2 / 4 4 » Adjust black arms (J) for a proper angle. * Adjust until they have shown as the illustrati 5 » · According to your desired hanging height to choose and use tubes (H). 1) Then pass the fixture wires through the chosen tubes (H),the swivel joint (F) and the canopy (E). 2) Be sure that all the threaded tubes are tightened, then screw the chosen tubes (H) onto the swivel joint (F) and the top of connector (I). * Hand tighten till snug. 6 » Attach mounting plate (C) to the outlet box with mounting screws (B). 7 » Make wire connections Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES. Page: 3 / 4 Connect ground wires according to the chart below A B Connect wires according to the chart below Connect Black or Red Supply Wire to: Connect White Supply Wire to: OUTLET BOX GROUND GREEN GROUND SCREW OUTLET BOX GROUND FIXTURE GROUND DIMPLES GREEN GROUND SCREW Black White *Parallel cord (round & smooth) *Parallel cord (square & ridged) FIXTURE GROUND Clear, Brown, Gold or Black without tracer Insulated wire(other than green) with copper conductor Clear, Brown, Gold or Black with tracer Insulated wire(other than green) with silver conductor CUPPED WASHER * Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.) Neutral Wire · Twist wires together with plastic wire connectors (A) until tightly joined. · Wrap each connector with approved electrical tape. · Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box. 8 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening canopy nuts (G) onto the pre assembled screws in mounting plate (C). Note: canopy (E) should be snug against the ceiling and canopy nuts (G). If not, adjust the threaded length on the mounting plate (C): · Unscrew the preassembled hex nuts. · Screw the preassembled screws in or out of mounting plate (C). · When the secure length is achieved, tighten the hex nuts and back to step 8. 9 » Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.) 10. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting! ORDERING PARTS Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts. CLEANING To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper. Page: 4 / 4Scribus PDF Library 1.5.6.svn