CRAFTEX CX512 6×9 Belt Disc Sander Instruction Manual

Instruction Manual for CRAFTEX models including: CX512 6 9 Belt Disc Sander, CX512, 6 9 Belt Disc Sander, Belt Disc Sander, Disc Sander, Sander

SALES03

CX512

Buy 6in. X 9in. Belt And Disc Sander at Busy Bee Tools

Manuals – Busy Bee Tools

File Info : application/pdf, 23 Pages, 1.41MB

CX512

MODEL CX512 6"×9" BELT DISC SANDER
Version 2.0- 2024

TABLE OF CONTENTS
General Safety Instructions ................................................................................... 3 CX512 Manual....................................................................................................... 4 Safety Precautions and Specification .................................................................... 5 Assembly............................................................................................................... 5 Installing Sanding Belt Fences .............................................................................. 6 Installing the Disc Table ........................................................................................ 6 PSA Sandpaper Disc Install................................................................................... 7 Adjusting Disc Table Angle .................................................................................... 8 Adjusting the Belt Assembly .................................................................................. 9 Grounding Instructions .......................................................................................... 10 Extension Cord Length .......................................................................................... 11 ON/OFF Switch ..................................................................................................... 12 Replacing the Sanding Belt ................................................................................... 13 Belt Tracking Adjustment....................................................................................... 14 Trouble Shooting Guide for CX512 ........................................................................ 16 Diagram for CX512................................................................................................ 18 Parts List for CX512 .............................................................................................. 19 Parts List for CX512-2 ........................................................................................... 20 Parts List for CX512-3 ........................................................................................... 21 Parts List for CX512-4 ........................................................................................... 22 Parts List for CX512-5 ........................................................................................... 23 Warranty................................................................................................................ 24
2

GENERAL SAFETY INSTRUCTIONS

Extreme caution should be used when operating all power tools. Know your power tool, be
familiar with its operation, read through the owner's manual and practice safe usage procedures at all times.

· ALWAYS read and understand the user manual before operating the machine.
· CONNECT your machine ONLY to the matched and specific power source.
· ALWAYS wear safety glasses respirators, hearing protection and safety shoes, when operating your machine.
· DO NOT wear loose clothing or jewelry when operating your machine.
· A SAFE ENVIRONMENT is important. Keep the area free of dust, dirt, and other debris in the immediate vicinity of your machine.
· BE ALERT! DO NOT use prescription or other drugs that may affect your ability or judgment to safely use your machine.
· DISCONNECT the power source when changing drill bits, hollow chisels, router

bits, shaper heads, blades, knives or making other adjustments or repairs.
· NEVER leave a tool unattended while it is in operation.
· NEVER reach over the table when the tool is in operation.
· ALWAYS keep blades, knives and bits sharpened and properly aligned.
· ALL OPERATIONS MUST BE performed with the guards in place to ensure safety.
· ALWAYS use push sticks and feather boards to safely feed your work through the machine.
· ALWAYS make sure that any tools used for adjustments are removed before operating the machine.
· ALWAYS keep the bystanders safely away while the machine is in operation

CX512 MANUAL

GETTING STARTED
WARNING
Be careful not to touch overhead power lines, piping, lighting, etc. if lifting equipment is used. Sander weighs approximately 88 lbs, proper tools, equipment and qualified personnel should be employed in all phases of unpacking and installation.
Cartons should be handled with care to avoid damage from dropping, bumping, etc. Store and unpack cartons with correct side up. After unpacking the Sander, inspect carefully for any damage that may have occurred during transit. Check for loose, missing, or damaged parts. If any damage or loss has occurred, a claim must be filed with the carrier immediately. Check for completeness. Immediately report any missing parts to the dealer.
The sander is shipped partially assembled. The end user will need to assemble loose parts to the machine.
IMPORTANT: The tool has been coated with a protective coating. In order to ensure proper fit and operation, the coating must be removed. Remove coating with mild solvents such as mineral spirits and a soft cloth. Non-flammable solvents are recommended. After cleaning, cover all

exposed metal surfaces with a light coating of oil.
CAUTION
Never use highly volatile solvents. Avoid getting cleaning solutions on paint as it may tend to deteriorate these finishes. Use soap and water on all painted components.
Contents
· Sander (1) · Miter gauge assembly (1) · Support rod assembly (1) · Table assembly (1) · Hardware bag (1) · Rubber foot (4) · Hex Wrench S+4x120 (1) · Operating instructions and parts
manual (1)
Unpacking:
· Carefully unpack the sander from the carton. Do not discard packing materials until after the machine has been inspected for damage and completeness. Locate loose parts and set aside.
Pre-inspection
· After unpacking the unit, carefully inspect for any damage that may have occurred during transit. Check

for loose, missing, or damaged parts. Shipping claims must be filed with the carrier. · Be sure that the voltage label on the unit matches your power supply.
· See General Safety Instructions, Cautions and Warnings as shown.
SAFETY PRECAUTIONS
Personal Safety
· Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in the moving parts of the machine.
· Wear protective hair covering to contain long hair.
· Wear safety shoes with nonslip soles.
· Wear safety glasses. · Wear a face mask or dust mask if the
operation is dusty. · Be alert and think clearly. Never
operate power tools when tired, intoxicated or when taking medications that cause drowsiness.
Work Area Preparation
· Keep the work area clean. Cluttered work areas invite accidents.
· Do not use power tools in dangerous environments. Do not use power tools in wet locations. Do not expose power tools to rain.
· The work area should be properly illuminated.

· All tools should be visually inspected before use, in addition to regular periodic maintenance inspections.
· Proper electrical receptacle should be available for the sander. Use a three prong only plugged into a grounded receptacle.
· Check for damaged parts and ensure all guards are in place and undamaged. Repair before use.

SPECIFICATIONS

Belt size

6 x 48"

Belt platen area

6 x 14-1/2"

Belt drum dimensions

2-7/8 x 6-1/8"

Table Area

6 x 11-1/2"

Table angle range

0 to 45 Deg.

Dust chute diameter

Belt speed

1836 SFPM

Disc diameter

Disc speed

2510 RPM

Base dimensions

12 x 18-1/8"

Switch

SP, Locking rocker.

Motor

1 HP, 120 V,

8.0 Amps

Weight

72 lbs

Ship weight

76 lbs

ASSEMBLY
Installing the Foot Pads
Four rubber foot pads are supplied with the machine to protect your work surface and to reduce any vibration that may develop during the sanding operation. The foot pads are easily installed as per Figure 1. No hardware is required.

Figure 1 Install Foot Pads.
Installing the Sanding Belt Fences
The sander includes two fences for use with the sanding belt. The small fence/platen attaches directly to the sanding belt frame, and is used for supporting small items being sanded. The larger fence/platen attaches to the small fence. It gives a larger support surface for sanding larger work pieces NOTE: These parts may be pre-assembled at the time of delivery. If not, follow the following parts assembly:
1. Install the small fence onto the sanding belt frame with the four hex screws and washers. See Figure 2.
Figure 2 Install the small fence. 2. Insert two Phillips head screws through the countersunk holes in the large fence and install the knobs

on their threaded ends. (Washers shown in Figure 3 are optional, not included with the sander).
3. Slide the large fence's two screws with knobs over the two slots in the small fence and fasten it in place. Depending upon the material being sanded, the fence can easily be removed by loosening the two knobs and sliding it off the small fence, See Figure 3.
Figure - 3 Install fence knobs. Installing the Disc Table Refer to figures 4 and 5. The larger worktable is used with the sanding disc. It should be used to support workpieces in all sanding operations except inside applications.
1. Place the worktable on to the sander frame, aligning the semicircle slot with the threaded hole.
2. Place a washer on the threaded shaft of each worktable handle, insert through the semicircular slot and tighten into the threaded hole. Repeat on the other side.

Adjust worktable to level or any angle in between 0 degrees and 45 degrees for sanding.
NOTE:
Always check to make sure the handles are tight before beginning any sanding operation.

NOTE: The 6" x 9" Belt Disc Sander only uses 9" diameter abrasive sanding discs with Pressure Sensitive Adhesive (PSA) backing. To apply the sandpaper:
1. The metal disc plate is preinstalled on the machine. Locate the 9" PSA sandpaper disc and peel the protective backing off.
2. Center the sandpaper over the metal disc plate, then press the sandpaper firmly in place. See Figure 6.
See page 9 for instructions on changing the sandpaper disc.

Figure 4
Figure 5
PSA Sandpaper Disc Install

Figure 6 Mount sandpaper disc.
INSTALLATION
Mounting the Sander
NOTE Although compact, the sander is heavy. At least two people are required to lift it from the carton.
Choose a suitable location to mount the sander. The sander must be installed in a place with a place with ample lighting and have the correct power supply.
7

Make sure there is plenty of room for moving the workpiece. There must be enough room that neither operators nor bystanders will have to stand in line with the wood while using the tool. Allow room so that the belt assembly can be positioned horizontally.
Figure 7 shows the base dimensions, mounting holes, and the required space to allow for table assembly in the horizontal position.

Ensure the sander is disconnected from the power source prior to commencing work.
1. To check the trueness of the 90 Deg. Angle of the disc sanding table, place a square or other measuring device on the table with the other end against the sanding disc. See Figure 8.

Figure 7 Base dimension and required space.
The sander must be bolter to a firm, level surface. The sander can be installed on a workbench or a tool stand using bolts, lock washers and hex nuts. (Not Supplied).
Adjusting Disc Table Angle

Figure 8 Checking the disc's trueness.
2. Loosen the disc table adjustment handle, and adjust the table angle to 90 Deg.
3. Re-tighten the disc table adjustment handle.
4. Adjust the angle scale pointer to Zero Deg.
5. To adjust the table angle to another angle, loosen the disc table adjustment handle.
6. Set the table at the desired angle using the angle scale pointer.
7. Re-tighten the disc table adjustment handle.
WARNING
To avoid jamming the workpiece or fingers between the table and sanding surface, the

table edge should be set to a maximum of 1/16 inches away from the sanding surface. See Figure 9.

3. In the horizontal position, there are two vertical padded set screws that support the sanding belt frame. These should be checked and adjusted, if necessary, to make sure they both touch the sanding belt frame supports. These screws will help relieve pressure on the casting during work. See Figure 11.

Figure 9.
Adjusting the Belt Assembly
The sanding frame can be adjusted easily between a vertical and horizontal position, or any other position to assist your sanding operation.
1. Loosen the hex screw that pulls the split casting together. This will allow the sanding belt frame to be moved to the desired work angle. See Figure 10.
Figure 10 2. Once the sanding belt frame is at the desired angle, re-tighten the hex screw to secure it in place.

Figure 11
Power Source
WARNING All electrical connections must be performed by an electrician.
Connect the sander to a supply circuit protected breaker or time delay fuse.
The motor is designed for operation on the voltage and frequency specified. Normal loads will be handled safely not more than 10% above or below the specified voltage.
Running the unit on voltages not within the range may cause overheating and burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified. The power supply to the motor is controlled by a single pole locking rocker

switch. Remove the key to prevent unauthorized use.
Grounding Instructions
WARNING
Improper connection of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to protect the operator from electric shock.
Check with a qualified electrician if grounding instructions are not understood or if in doubt if the tool is properly grounded. The tool is equipped with an approved 3conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 15) for your protection against shock hazards. Grounding plug should be plugged directly in to a properly installed and grounded 3prong grounding-type receptacle, as shown (Figure 12).
Figure 12 3-prong receptacle Do not remove or alter the grounding prong in any manner. In the event of malfunction

or breakdown, grounding provides a path of least resistance for electrical shock.
WARNING
Do not permit fingers to touch the terminals of the plug when installing or removing from the outlet.
The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with local codes and ordinances. Do not modify the plug provided. If it will not fit in the outlet, have the proper outlet installed by an electrician.
Inspect the tool cords periodically, and if damaged, have them repaired by an authorized service facility.
Green (or green and yellow) conductor in the cord is the grounding wire. If repair or replacement of the electrical cord or plug is necessary, do not connect the Green (or green and yellow) wire to a live terminal.
Where a 2-prong wall receptacle is encountered, it must be replaced with a properly grounded 3-prong receptacle installed in accordance with the national Electric Code and local codes and ordinances.
Extension Cords
· The use of any extension cord will cause some drop in voltage and loss of power.
· The wires of the extension cord must be of sufficient size to carry

the current and maintain adequate voltage. · Use the table to determine the minimum wire size (A.W.G.) extension cord. · Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug. · If the extension cord is worn, cut or damaged in any way, replace it immediately.

Extension Cord Length

Length

Wire Size A.W.G

Up to 25 ft

25-50 ft

NOTE
Using extension cords over 50 ft long is not recommended.

OPERATION
WARNING
Operation can result in foreign objects being thrown into your eye which can result in severe eye damage. Always wear safety goggles before commencing power tool operation.
CAUTION
Always observe the following safety precautions:

· Whenever adjusting or replacing any parts on the tool, Turn the switch off and remove plug from the power source.
· Recheck table handles and bolt. They must be tightened securely.
· Make sure all guards are properly attached and securely fastened.
· Make sure all moving parts are free and clear of any interference.
· Make sure all fasteners are tight and have not vibrated loose.
· With power disconnected, test operation by hand to verify clearance and adjust if necessary.
· Always wear eye protection or a face-shield.
· Make sure abrasive belt tracks properly. Correct tracking gives optimum performance.
· After turning switch on, always allow the belt to come to full speed before sanding or grinding.
· Be sure the disc runs counterclockwise. Abrasive belt must travel downward.
· Keep your hands clear of abrasive belt, disc, and all moving parts.
· For optimum performance, do not stall the motor or reduce speed. Do not force the work into the abrasive belt or disc.
· Always support work piece with table or work stop when sanding with the belt and with table when sanding with disc.

· Never push a sharp corner of the workpiece against belt or disc. Abrasive backing may tear.
· Replace the abrasive belt or disc when they become loaded (glazed) or frayed.
WARNING
Review all safety precautions before turning on the machine, making sure that you fully understand the features, adjustments and capabilities of the machine outlined in this manual.
ON/OFF Switch
The ON/OFF switch needs to have the safety switch key inserted before the switch can be used. This feature prevents unauthorized use of the sander. See Figure 14.
Figure 14 Remove safety key to prevent sander use.
Abrasive Belt Sanding
· Finishing flat surfaces: Hold workpiece firmly with both hands; keep fingers away from abrasive belt.

Use table to position and secure work being sanded. Keep the end butted against the table and move work evenly across the abrasive belt. · Finishing long pieces: Use belt in horizontal position with the work stop. Apply only enough pressure to allow the abrasive belt to remove material. Use work stop to position and secure work being sanded. Keep the end butted against the table and move work evenly across the abrasive belt. Use extra caution when sanding very thin pieces. · Finishing curved edges: Finish outside curves on flat portion of abrasive belt. Finish inside curves on the idler drum portion of the abrasive belt. · Finishing end grain: It is more convenient to finish the end of long workpieces with the abrasive belt in the vertical position.
Position the table on the belt side of sander. Move work evenly across abrasive belt. For accuracy, use the miter gauge. Table may be tilted for beveled work.
Disc Sanding
· Abrasive disc sanding is well suited for finishing small flat surfaces and convex edges.
· Move workpiece across downside (left) of the abrasive disc. Hold workpiece firmly with both hands;

keep fingers away from abrasive disc. · Abrasive disc moves fastest and removes more material at the outer edge. · For accuracy, use the miter gauge.
Replacing the Sanding Belt
1. Remove the plastic side cover from the frame by unscrewing the knob. See Figure 15

with the direction arrow pointing in the proper direction. See Figure 17. Make sure the belt is centered on both drums. 5. Slide the tension lever to the left to apply tension to the belt. See Figure 16. 6. Re-install the small fence and slide cover onto frame (removed in Step 1 & 2). 7. Plug in the power cord. Turn the switch to "ON" and note if the belt tends to move to the right or left on the drums. The belt should be running in the center of the drive drums. If it is not the belt tracking needs adjustment. See instructions on sanding belt tracking.

Figure 15
2. Remove the small fence. See page 3 for instructions on installing this part. Slide the tension lever to the right to
3.
release the belt tension. See Figure 16.
NOTE
Above the tension lever, there is a direction arrow. The sanding belt must run in the direction of this arrow so that the splice does not come apart. See Figures 16 and 17.
4. Remove the old belt by sliding it off to the left of the frame. Place the new sanding belt over the drums

Figure 16
Figure 17 Belt Tracking Adjustment Refer to Figure 18.

1. Belt tracking on the center of the drive wheels is pre-set at the factory. If an adjustment needs to be made, the sander must be turned on. a) If the sanding belt moves toward the disc, slowly turn the tracking knob clockwise ¼ turn. b) If the sanding belt moves away from the disc, slowly turn the tracking knob counterclockwise ¼ turn.
2. Slowly turn the belt tracking knob noting the belt movement. Re-adjust the tracking knob, as necessary, until the belt runs true in the center of the drums.
Figure 18
Sanding Disc Installation
Refer to Figure 19.
The sandpaper disc can be removed with the table installed, or with the table removed to give more working access to the disc, if needed.
1. Peel the abrasive disc from the metal disc plate. A putty knife may help in this process.

2. Make sure the disc plate is clean of any residue. Mineral spirits will soften the PSA adhesives for its removal. Rotate the disc by hand to access all of the disc surface.
3. Peel the protective backing from the new PSA 9" abrasive sanding disc, then center and press the sanding disc firmly onto the metal disc plate.
4. Replace the sanding table if it was removed.
Figure 19
MAINTENANCE
WARNING
Make certain that the unit is disconnected from the power source before attempting to service or remove any component.
Cleaning
· Keep the machine and workshop clean. Do not allow sawdust to accumulate on the tool.
· Keep the drums clean. Dirt on the drums will cause poor tracking and belt slippage.

· Operate the tool with a dust collector to keep dust from accumulating.
· Be certain the motor is kept clean and is frequently vacuumed free of dust.
· Use soap and water to clean painted parts, rubber parts and plastic parts.
Lubrication
The shielded ball bearings on the tool are permanently lubricated at the factory. They require no further lubrication.
· When the operation seems stiff, a light coat of paste wax applied to the belt and disc tables will make it easier to feed the work while finishing.
· Do not apply wax to the belt platen. Belt could pick up wax and deposit it on the drums causing the belt to slip.
Tool Upkeep
· If the power cord is worn, cut or damaged in any way, have it replaced immediately.
· Replace worn abrasives when needed.
· Replace any damaged or missing parts. Use parts list to order parts.
· Any attempt to repair the motor may create a hazard unless the repair is done by a qualified technician.
15

Trouble Shooting Guide for CX512

Problem

Possible Cause

Solution

Motor will not start

1. Faulty or defective switch

1. Replace switch.

2. Faulty or blown capacitor. 2. Replace the capacitor.

3. Blown fuse or tripped circuit breaker.
4. Low line voltage

3. If the fuse is blown replace it with the required size. If the breaker is tripped, reset it.
4. Check power supply for voltage and correct as needed

Motor will not start due to

1. Faulty or defective plug

blown fuse or tripped breaker in

service panel

2. Faulty or defective switch

3. Defective or damaged power cord

1. Have the plug replaced.
2. Have the switch replaced.
3. Has the power cord replaced if damaged?

4. Faulty or incorrect Internal wiring

4. Contact Busy Bee Tools Customer service.

5. Overloading due to binding or 5. Clean debris from around

jamming of machine

wheels and shaft or replace

bearings if seized.

Motor overheats

1. Motor is overloaded

6. Reduce load on motor

Motor fails to develop full

1. The wire gauge is undersized,

power. (power output decreases or circuit is too long.

rapidly with drop in voltage to motor terminals)

2. The circuit is overloaded the lights, appliances, or other

motors.

1. Increase the wire gauge and short the run length of the circuit.
2. Reduce load on circuit or try using another circuit.

3. General overloading of power.

3. Request a voltage check from your power company

Abrasive belt runs off top wheel 1. Not tracking properly

1. See the Adjusting sanding belt section on page 6

Machine slows down during operation
Motor stalls (resulting in a tripped breaker or blown fuse)

1. Applying to much pressure to 1. Ease up on pressure and let the

workpiece

machine do the work.

2. V-belt (drive belt is slipping

2. Adjust and increase the V-belt tension

1. Low voltage
2. Wrong size fuse or breaker for circuit load
3. Loose connection or short circuit in motor connections
4. Motor overloaded

1. Correct the low line voltage conditions.
2. Install the appropriate size breaker or fuse.
3. Inspect motor for loose connections, worn, or damage wires. Replace if required.

4. Reduce the load on the motor

Part Number
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Parts List for CX512
Description
Phillips screw + flat washer M4x6 Phillips screw + spring washer + flat washer M4x8
Base Plate Phillips screw M5x8
Lock handle Power cord Dust hose V-belt A580 Hex screw M6x8 Cord clip 6P4 Key A5X15
Motor Nut M8 Driving pulley Dust cover Hex screw + spring washer + flat washer M5x10 Flat washer D8 Hex screw M8x55 Hex nut, I type M8 Bearing cap Ball bearing 6201 Hex screw M8X12 Driving drum Driving shaft Supporting plate Hex screw + spring washer + flat washer M8X30 Hex screw M8X16
Base Rubber foot Phillips screw M5X12 Capacitor bracket Hex nut, I type M5 Phillips screw M4X10 Hex screw + spring washer + flat washer M6x12 Capacitor 20µF/120V Capacitor 20µF/300V Capacitor bracket Hex screw + spring washer + flat washer M5x18 Belt cover Disc table
Dust port Phillips screw + spring washer M5x25

Quantity
4 4 1 4 2 1 1 1 5 1 2 1 2 1 1 10 2 2 5 1 3 3 1 1 1 2 4 1 4 1 1 3 11 4 1 1 1 2 1 1 1 3

Phillips screw + spring washer + flat washer M5x12

Idler pulley

Fixing ring

Belt frame assembly base

Bearing Cap

Ball bearing 6202

Hex screw M8x30

Hex screw M5x30

Supporting plate

Platen

Sanding belt (6" x 48" 120 grit)

Phillips screw M6x14

Fence

Fence Support

Locking nut

Flat Washer M8

Rubber foot

Dust port cover

Phillips screw + spring washer M5x16

Tensioning Spring

Bushing

Driven drum support

Nut M5

Belt tracking knob M8

Rubber washer

Adjustment Rod

Adjustment spring

Spring

Belt tension handle

Powder metal bushing

Position ring for driven shaft

Inner hex position screw M5x6

Spring washer for shaft M12

Driven shaft

Driven drum

Miter gauge knob

Miter gauge label

Miter gauge

Phillips screw + spring washer + flat washer M5x8

Phillips screw M8x25

Slide bar

Miter gauge pointer

Disc table left support

Left scale

Right scale

Disc table right support

Spring washer M6

Handle

Inner hex head screw M5x56

Switch guard

Phillips head screw M3x10

Switch key

Disc guard

Big washer M6

Sanding disc, 9" PSA 80 grit

Aluminum disc plate

Disc cover

100

Adapter

101

Pointer

102

Hex wrench S=4

103

Hex wrench

104

Clip

105

Hex nut M5

106

Phillips screw M5x10

107

Hex nut M6

108

Phillips screw + outer tooth washer + flat washer M5x16

109

Screw Hex M6X16

110

Graphite Pad

Item Number
1 2 3 4 5 6 7 8 9 10 11

Description
Upper Long Cross Bar Upper Short Cross Bar Lower Long Cross Bar Lower Short Cross Bar
Stand Leg Bolt M6-1.0X12mm
Nut Hex M6-1.0 Rubber Feet
Bolt Hex Inner M8-1.25X55mm Washer Flat M8 Nut Hex M8-1.25

Quantity
2 2 2 2 4 32 32 4 4 8 4

WARRANTY
CRAFTEX 3 YEARS LIMITED WARRANTY
Craftex warrants every product to be free from defects in materials and agrees to correct such defects where applicable. This warranty covers three years for parts and 90 days for labor (unless specified otherwise), to the original purchaser from the date
of purchase but does not apply to malfunctions arising directly or indirectly from misuse, abuse, improper installation or assembly, negligence, accidents, repairs or alterations or lack of maintenance.
Proof of purchase is necessary.
All warranty claims are subject to inspection of such products or part thereof and Craftex reserves the right to inspect any returned item before a refund or replacement may be issued.
This warranty shall not apply to consumable products such as blades, bits, belts, cutters, chisels, punches etceteras.
Craftex shall in no event be liable for injuries, accidental or otherwise, death to persons or damage to property or for incidental contingent, special or consequential damages arising from the use of our products.
RETURNS, REPAIRS AND REPLACEMENTS To return, repair, or replace a Craftex product, you must visit the appropriate Busy Bee Tools showroom or call 1800-461-BUSY. Craftex is a brand of equipment that is exclusive to Busy Bee Tools. For replacement parts directly from Busy Bee Tools, for this machine, please call 1-800-461-BUSY (2879), and have your credit card and part number handy.
· All returned merchandise will be subject to a minimum charge of 15% for re-stocking and handling with the following qualifications.
· Returns must be pre-authorized by us in writing. · We do not accept collect shipments. · Items returned for warranty purposes must be insured and shipped pre-paid to the nearest warehouse. · Returns must be accompanied by a copy of your original invoice as proof of purchase. Returns must be in an
unused condition and shipped in their original packaging a letter explaining your reason for the return. Incurred shipping and handling charges are not refundable. · Busy Bee will repair or replace the item at our discretion and subject to our inspection. · Repaired or replaced items will be returned to you prepaid by our choice of carriers. · Busy Bee reserves the right to refuse reimbursement or repairs or replacement if a third party without our prior authorization has carried out repairs to the item. · Repairs made by Busy Bee are warranted for 30 days on parts and labor. · Any unforeseen repair charges will be reported to you for acceptance prior to making the repairs. · The Busy Bee Parts & Service Departments are fully equipped to do repairs on all products purchased from us with the exception of some products that require the return to their authorized repair depots. A Busy Bee representative will provide you with the necessary information to have this done.
23

Microsoft Word for Microsoft 365