Business Community
CE Regulatory Compliance | TP-LinkTP-Link Product Support - Wireless Networking Equipment SupportDownload Center | TP-LinkRegulatory Compliance | TP-Link
Installation Guide for tp-link models including: EAP650, EAP775, EAP723, Omada EAP650 Wireless Access Point, Omada EAP650, Wireless Access Point, Access Point, Point
EAP650(UN) V2 Multi-model Installation Guide | Omada Network Support BookmarksCopy Link
EAP650(UN) V2 Multi-model Installation Guide | Wsparcie Techniczne sieci Omada
File Info : application/pdf, 2 Pages, 778.14KB
DocumentDocumentQuick Installation Guide Wireless Access Point Setup with videos Visit https://www.tp-link.com/support/setup-video/?type=smb or scan the QR code to search for the setup video of your product model. Note: EAP650 is used as an example throughout the Guide. Images may differ from your actual product. ©2024 TP-Link 7106511712 REV2.0.0 1 Hardware Overview Front Panel 2 Hardware Installation The EAP can be mounted to the ceiling, the wall, or in a junction box, using the accessories in the package. Choose a mounting option below. Note: This product requires heat dissipation through the metal bracket during use. Please be careful not to touch the metal bracket in the heat dissipation. Option 1 Ceiling Mounting (on a Tile) Option 2 Ceiling Mounting (on a T-bar) Option 3 Wall Mounting Option 4 Junction Box Mounting Option 2: Ceiling Mounting (on a T-bar) T-bar Mounts Option 1: Ceiling Mounting (on a Tile) Note: Make sure that the ceiling tile is larger than the EAP. Washers Pan-head Screws Wing Nuts 1 Remove a ceiling tile. 1 Remove the ceiling tiles next to a T-bar. 2 Detach the mounting screw and loosen the set screws of each T-bar mount. LED Indicator Blue On: Working normally/Initializing. For EAPs with dual-color LED: Normal power supply Orange On: For EAPs with dual-color LED: Low power supply Off: Working abnormally/Power off/LED is turned off. Flash: · Flash twice: Initialization is complete. · Flash quickly: The EAP is resetting, or the Omada Controller is locating the device*. · Flash once per second: The EAP is upgrading. · Sustained on with brief off: The EAP is in the isolated state. * When the Locate feature is activated in the Omada Controller, the LED will flash quickly for 10 minutes to help you locate and identify the device. You can disable this feature manually to stop the device from flashing. Rear Panel Common rear panels: 25 mm (63/64 in) 4 mm (5/32 in) RESET With the device powered on, press and hold the button for about 5 seconds until the LED flashes quickly, then release the button. The device will restore its factory settings. Ethernet Port: ETH (PoE) Connect to a gateway/router or a switch to transmit data, or to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable. Notes: 1. For EAPs with 10Gbps port, if you use a Cat 5E cable, the 10Gbps link of the Ethernet port is less than 55m. To achieve a longer transmission distance, use a shielded Cat 6A cable. 2. For ultra-slim products with limited space for Ethernet ports, Cat 7 and Cat 8 network cables may be incompatible due to the lack of a standard buckle design. Power Port Connect to a standard electrical wall outlet via a power adapter to power the EAP. Note: Power adapter is not included in the package contents of certain models. For details, refer to the product specifications or datasheet. For power supply specifications, refer to the product label. 2 Place the mounting bracket in the center of the ceiling tile. Mark positions for the screw holes and the Ethernet cable hole, then drill holes at the marked positions. 3 Secure the mounting bracket to the ceiling tile using pan-head screws, washers, and wing nuts. 4 Feed the Ethernet cable through the hole and set the ceiling tile back into place. 5 Connect the Ethernet cable to the Ethernet port on the EAP. Attach the EAP to the mounting bracket, then rotate it until it locks into place. 60 mm 3 Place the T-bar mounts against the T-bar and turn clockwise. Tighten the set screws. 4 Secure the mounting bracket to the T-bar mounts using the mounting screws. 5 Route the Ethernet cable through the square cable hole on the mounting bracket. Set the ceiling tiles back into place. 6 Connect the Ethernet cable to the Ethernet port on the EAP. Attach the EAP to the mounting bracket, then rotate it until it locks into place. Option 3: Wall Mounting Plastic Wall Anchors Self-tapping Screws Option 4: Junction Box Mounting Prepare the cables and the junction box in advance. Ensure that the mounting holes align to your junction box. *Compatible junction boxes: 4 Software Configuration Option 1: Standalone Mode Configure and manage EAPs separately on the standalone web page (https://tplinkeap.net). Note: The EAP's standalone web page is inaccessible while the EAP is managed by a Controller. 7.6 mm (19/64 in) 1 If your Ethernet cable feeds through the wall, position the mounting bracket below the cable hole. Mark positions for the screw holes, then drill holes at the marked positions. 2 Insert the plastic wall anchors into the holes. 1 Route the cables through the square cable hole on the mounting bracket, and secure the mounting bracket to the junction box using screws. Gateway/Router Switch Scan for Standalone EAP Start Guide EAP Clients EAP 2 Connect the Ethernet cable to the Ethernet port on the EAP. Option 2: Controller Mode Configure and manage EAPs (and other Omada devices) in batches on an Omada Controller. 3 Secure the mounting bracket to the wall by driving the self-tapping screws into the anchors. Make sure that the shoulders of the mounting bracket are on the outside. 3 Attach the EAP to the mounting bracket, then rotate it until it locks into place. EAP Gateway/Router Switch EAP 4 Connect the Ethernet cable to the Ethernet port on the EAP. 5 Attach the EAP to the mounting bracket, then rotate it until it locks into place. Safety Information · Keep the device away from water, fire, humidity or hot environments. · Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. · Do not use the device where wireless devices are not allowed. · Do not use damaged charger or USB cable to charge the device. · Do not use any other chargers than those recommended. · Adapter shall be installed near the equipment and shall be easily accessible. · The EAP can be powered only by a power adapter or a PSE device (such as a PoE switch) which complies with Power Source Class 2 (PS2) or Limited Power Source (LPS) of IEC 62368-1. 3 Power Supply Power on the EAP by a power adapter or a PSE device (such as a PoE switch). Option 1: Via PoE Switch Connect the EAP to a PoE switch via an Ethernet cable. Note: For PoE power supply specifications, refer to the product label. PoE Switch Option 2: Via Power Adapter Connect the EAP to a standard electrical wall outlet via a power adapter. Note: Power adapter is not included in the package contents of certain models. For details, refer to the product specifications or datasheet. For power supply specifications, refer to the product label. Power Adapter Switch TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011 /65/EU and (EU) 2015/863. The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/ TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/ Controller Omada Or Omada Cloud-Based Hardware/Software Controller Controller EAP Scan for Omada Controller Start Guide EAP Clients For more configurations, refer to the user guides of the Controller and EAPs. The guides can be found in the download center of our official website: https://www.tp-link.com/support/download/?type=smb Omada App With the TP-Link Omada app, you can access and manage your Omada devices at a local site or remotely with a tap on your phone. You can download and install the TP-Link Omada app from the App Store or Google Play. or Scan for Omada Omada To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com/business to join TP-Link Community. For technical support, the user guide and other information, please visit https://www.tp-link.com/support/?type=smb, or simply scan the QR code.