EcoFlow RIVER 600 Extra Battery User Guide

Safety Guidelines and Notices

NOTICE: Improperly following instructions may result in property damage and minor physical harm.

CAUTION: Improperly following instructions may result in property damage and serious physical harm.

WARNING: Improperly following instructions may result in property damage, major accidents, and serious injury.

Always read the entire user manual to familiarize yourself with the product's features before operation. Failure to operate correctly may lead to product damage, personal property damage, or serious injury. EcoFlow is not liable for damages caused by improper use or alteration of the product. Follow all instructions and warnings before assembly, setup, or use.

Product Safety Guidelines

• Keep the product dry and avoid high heat.
• Never disassemble, puncture, shock, crash, or incinerate the product or accessories.
• Ensure the Extra Battery Module is installed with the RIVER 600 promptly after unboxing. Pay attention to static electricity during installation.
• Recycle and dispose of the RIVER 600 according to local regulations.
• Supervision is required for children or individuals with disabilities using the machine.
• Do not expose the product to liquids or immerse it in water. Avoid leaving batteries in rain or near moisture, as this can cause short circuits, component failure, fires, or explosions.
• Only use genuine EcoFlow parts. Visit http://www.EcoFlow.com to purchase replacement parts. EcoFlow is not responsible for damage caused by non-EcoFlow parts.
• Never install or remove modules while the RIVER 600 is powered on. Do not plug or unplug modules when the product is on, as this may damage the power interface.
• Operate the product within temperatures of -4°F to 140°F (-20°C to 60°C). Exceeding these temperatures can cause fire or explosion. Operation below -4°F (-20°C) will severely affect performance; allow the product to return to normal operating temperature before use.
• Avoid using the product in strong electrostatic or electromagnetic environments, which can cause the battery control board to malfunction.
• Never disassemble or pierce the product; this can lead to leaks, fire, or explosion.
• Do not use the product if it has been in a crash or experienced a heavy bump.
• If the product falls into water, remove it immediately and place it in a safe, open area, maintaining a safe distance until it is completely dry. Dispose of it properly. In case of fire, use water or water mist, sand, a fire blanket, or a dry powder/CO2 extinguisher.
• Do not place the machine in a microwave or pressurized container.
• Prevent metal objects from inserting into the device case, outlets, or controls, as this can cause short circuits.
• Avoid collisions and do not place heavy objects on the machine.
• Clean any dirt on plugs or outlets with a dry cloth to prevent abrasion and energy loss.

Product Charging

• Always use EcoFlow approved charging cables.
• Place the product on the ground away from flammable materials during charging. Never leave the battery unattended while charging.
• Do not charge the product immediately after heavy use if it is too hot; allow it to cool to room temperature. The battery may not charge outside the 32°F to 104°F (0°C to 40°C) range. The ideal charging temperature is 71°F to 82°F (22°C to 28°C).

Product Storage and Transportation

• Keep out of reach of children. Seek medical attention immediately if any parts are swallowed.
• Charge the battery before storing if a low-battery warning appears. Long-term storage of a depleted battery may cause damage. Batteries may enter hibernation mode if depleted and stored for extended periods; recharging can reactivate them.
• Do not place the product near heat sources like cars in direct sunlight, fire sources, or heating stoves.
• Store the product in dry environments and avoid contact with water.
• Ensure no small metal objects can fall on or around the product during storage.
• Never transport a product with a battery power level higher than 30%.

Product Battery Disposal

• Dispose of the product in designated recycling boxes only after complete discharge. Batteries contain hazardous chemicals; follow local regulations for disposal and recycling.
• Dispose of the product immediately if it cannot be powered on after over-discharging.

Product Maintenance

• Do not store the product in environments below -4°F (-20°C) or above 140°F (60°C).
• Battery life may be reduced if not used for extended periods.
• Fully charge and discharge the battery at least once every 3 months to maintain battery health.

Travel Notice

Carrying lithium batteries and equipment with a capacity greater than 160Wh on airplanes is forbidden due to regulations. Do not bring this product on flights.

RIVER 600 Extra Battery Module Installation Instructions

Congratulations! You now own the best quality portable power station Extra Battery. This guide will help you install and use the Extra Battery Module to enhance your Portable Lithium Generator experience.

NOTICE: Ensure the RIVER 600 is turned off before installation by pressing and holding the ON/OFF power button. Do not turn the RIVER 600 on before installing the bottom cover to avoid poor battery contact. After installation, restart the product. Frequent removal of the battery may affect the cell balancing function and user experience. If adding an expansion battery after prolonged use of the RIVER 600, output may be affected by battery balance inconsistencies; it is recommended to purchase the RIVER 600 and battery pack simultaneously. Charge the product to 100% before proceeding.

Step 1: Prepare for Installation

Turn off the RIVER 600. Use the screwdriver from the extra battery module kit to locate and remove the four screws on the bottom cover. Pay attention to anti-static protection during this process.

Step 2: Remove Bottom Cover

Unscrew the 4 screws as shown in the diagram and remove the bottom cover. You will see the male battery socket. Position the extra battery module as indicated.

Step 3: Connect Battery Module

Align the male and female battery sockets and connect them securely. Close the bottom cover. Use the four long screws provided in the kit to secure the cover.

Step 4: Power On and Verify

Place the RIVER 600 upright and turn it on. The extra battery module's ambient light should turn blue, moving from the middle to the sides. If the extra battery module indicator light appears on the RIVER 600's display, the module is activated successfully. Ensure the machine is fully charged before use. If the ambient light or indicator light is not active, repeat Step 2 and check the connection.

Ambient Light Area

Status Signals

Powering Up: The blue light will move from the middle to the sides.

Powering Down: The blue light will move from the sides to the middle.

Charging: The blue light will move from left to right repeatedly.

Customizing the Ambient Light

Access 'Module Settings' to configure various functions:

• Turn the ambient light on/off or set it to stay on (can be active in standby mode).
• Select your preferred color.
• Adjust the brightness of the light.
• Choose a lighting mode: Default, Breathing, Flow, Polar, or Rainbow. Customize your lighting experience.

Technical Specifications

General Specs

• Net Weight: 5.5 lbs (2.5 kg)
• Dimensions: 11.2 x 7 x 2.3 in (28.5 x 18 x 5.9 cm)
• Capacity: 288Wh (28.8V)
• Testing and Certification: UL Standard, CE, FCC, RoHS

Battery

• Cell Chemistry: Lithium-ion
• Discharge Temperature: -4 to 140°F +/-5°F (-20 to 60°C +/-3°C)
• Charge Temperature: 32 to 113°F +/-5°F (0 to 45°C +/-3°C)
• Shelf Life: 1 Year (after fully charged)
• Cycle Life: 500 Cycles (80% capacity)

Note: Weight, size, and other specifications may have measurement errors. Please refer to actual measurements.

What's in the Box

• Extra Battery Module
• 4 Long Screws
• Cross Screw Driver
• User Manual and Warranty Card