Instructions for FLEXIHIRE models including: HD14VO CC Style Road Roller, HD14VO, CC Style Road Roller, Style Road Roller, Road Roller, Roller
DBLE DRUM ROLLER ROLLER 3T TO 4T HAMM HD14VO ation | Flexihire
File Info : application/pdf, 1 Pages, 580.09KB
DocumentDocumentSafe Operating Procedure PPE Required CA & CC Style Road roller General Safety Instructions ·Complete pre-start checklist ·Read Manufacturers Operation Manual (www.flexihire.com.au) ·Report any faults or damage to Flexihire 1300FLEXIHIRE ·Do not wear loose clothing or jewellery ·Do not operate equipment near pedestrians or people ·Do not operate without the appropriate PPE as detailed ·Do not operate equipment under the influence of drugs or alcohol General Engine Safety ·Refuelling Do not smoke, or introduce ignition source, always turn engine off and allow engine to cool first, relieve fuel pressure by loosening cap slowly, wipe clean any fuel spills prior to re-start, If fuel spilled on clothes change clothes, ensure cap is replaced & store fuel vessel away from work area ·Do not breathe fuel vapour& replace cap securely after fuelling ·Do not operate engine without adequate ventilation ·Beware of hot surfaces on engine & other parts Risk Assessment ·Assess the immediate work area for any hazards ·Control or eliminate all the risks associated with the hazards ·Hazards to check for that may require risk control- Overhead power lines Working at height Digging Falling objects Confined space High Voltage Traffic & moving machinery Any stored energy Stored energy air, hydraulic, electricity, pressure Operating Safety Instructions Ensure you are familiar with the emergency stop, engine shut down procedure and braking systems. Ensure Emergency stop and battery isolator is set to operate prior to entering cab. Do not operate near a trench, gulley, valley or drop off in the ground & Avoid driving across a slope and never drive on a slope greater than 20 degrees or 36%. Use lowest gear on a slope. Ensure you always maintain 3 points of contact climbing in and out of roller, beware of door pinch points & test it opens from inside. Never mount roller whilst it is moving. Ensure segregation from general traffic flow and pedestrians. It is recommended to maintain a 3m exclusion zone Ensure articulation lock is removed prior to normal operation Avoid sharp turns Always wear seat belt and be seated during operation Beware of soft, damp and wet soils that may give way Do not operate loader if you have do not have vision as required by your Do not operate near a trench, gulley, valley or drop off in the ground & standard Drivers Licence Avoid driving across a slope, exercise care and never drive on a slope Do not operate roller with any passengers greater than 20 degrees or 36% Do not operate roller unless you are competent to operate Do not adjust amplitude during operation stop first If Applicable ensure Vibration / amplitude switch is set to "OFF" prior to When driving close to unsafe edges or holes, ensure at least 2/3 of the staring and especially during loading or unloading drum width is on firm ground Plan work area & set mirrors prior to operation Ensure parking brake is engaged prior to leaving roller Do not operate plant in confined spaces Do not park roller on uneven ground Never use petrol as a cleaning agent on roller Read Operation Manual prior to servicing or towing ROPS (Roll over protection structure) is always recommended on slopes All hydraulic lines and fluid cooling systems are pressurised so never and if damaged cease work immediately and contact Flexihire open, cut or damage lines Do not operate roller until hydraulic fluids have reached operating temperature as breaking distance impacted Battery isolator located in engine compartment. Engine hood must be unlocked during operation so the isolator can be quickly accessed. Never climb on roller Test the parking brake prior to operation while rolling slowly in the forward direction engage brake roller must stop if failure tag out machine immediately If fitted with a strike off blade only use in the forward direction and when not using always operate with the blade in the upper most position If the machine tips do not jump, brace yourself, stay in cab, keep seatbelt fastened, hold on and lean away from point of contact Never open the radiator cap when the engine is running or hot Only approved service personnel to work on air conditioning as it contains harmful gases and high pressure Prior to Service or working on Roller lock out articulation, tag out roller, remove keys, chock wheels and drums If lifting roller ensure articulation lock is engaged prior to lift For transporting, ensure the roller is secured to the truck in line with the Australian Load Restraint Guide 2018. Secure seat prior to operation and always close door on cab prior to operation Never operate or start the machine from outside the cab or seat as you could move the controls the wrong way and cause serious injury. Maintain proper tyre pressure refer manufacturer specifications FMS10-5.1.3.9.4.1 SOP CA & CC Roller Version #: FLX 3.2 Issue: December 2022 Review: December 2027