User Guide for PULSE EIGHT models including: MS SERIES One IP Transceiver, MS SERIES, One IP Transceiver, IP Transceiver, Transceiver
Pulse Eight OneIP AVoverIP Transceiver | Product Solutions Group
Product Solutions Group | Product Solutions Group
Search results | Product Solutions Group
ONEIP NETWORK CONFIGURATION GUIDE - PAKEDGE MS SERIES V 1.0 INTRODUCTION The Pulse-Eight OneIP transceiver is an ultra-low latency, AV-over-IP solution capable of distributing UltraHD 4K HDMI 2.0 video (18Gbps), with support for HDR, over a 1Gbps Ethernet network. The following is a step-by-step tutorial for configuring the Packedge MS series switches for use with Pulse-Eight OneIP TRX units. Please follow the instructions below before connecting any OneIP devices to the switch. SUPPORTED PRODUCTS · Pakedge MS series switches. Note: Please note this has only been tested with MS2424 at the present time. IMPORTANT NOTES! Do NOT connect any OneIP devices to the switch before configuration is completed, doing so may cause the switch to run slow or crash due to multicast data flooding the network. 1 ONEIP NETWORK CONFIGURATION GUIDE - PAKEDGE MS SERIES pakedge Router Secondary Network Switch Core Network Switch AVoIP Switch CORE SWITCH (OR SINGLE SWITCH) CONFIGURATION Log in to the Pakedge Switch web interface. The Pakedge MS switches are set to DHCP by default; to find an IP address, you need to scan the network or check the DHCP server; if no DHCP server is available, the switch will default to 192.168.1.205. 1. Log in to the Web UI. The default credentials are admin and password. 2. Create a new secure password and username. 3. Set the switch to a static IP address or DHCP reserved from the DHCP server (optional). a. Select "Configure" then under "LAN" change mode to Static and set the desired IP address, Subnet Mask, and Gateway. b. Save the settings by clicking "Apply" in the top right corner of the screen. The switch will reboot and use the static or reserved IP address. c. Once "Submitting" shows on the screen, close the browser window. 4. Log in to the Web UI using the new IP address, username, and password. 5. From the main menu, select "Advanced" and then `IGMP Snooping' under the switching section. 2 ONEIP NETWORK CONFIGURATION GUIDE - PAKEDGE MS SERIES 6. Enable the IGMP Snooping Global Configuration and Status toggle switch and click "Apply". 7. Move to the VLAN Status page, and click "OPTIONS" button to add a VLAN entry. 8. Select the VLAN ID on which the OneIP devices are connected and disable Fast Leave for all switches. 3 ONEIP NETWORK CONFIGURATION GUIDE - PAKEDGE MS SERIES 9. Click the Apply button in the top right corner of the page. 10. On the Multicast Router VLAN Configuration page, enable MRouter Learning on all ports and click Apply. 11. Go to Advanced > Unregistered Multicast Behaviour > Configuration. Set Unregistered Multicast Behaviour Configuration to Drop. Click Apply. 12. If you notice an entry for EXC_default_list under the Exemptions list, proceed to the next steps. If not, then your configuration is complete. 13. Click on the Interface Configuration tab, then select Options and Edit. 4 ONEIP NETWORK CONFIGURATION GUIDE - PAKEDGE MS SERIES 14. To select all entries in the EXC_default_list, click the box next to Interface. Then, click Edit Selected. 15. Click the "x" in the EXC_default_list object to delete it. 16. Click Save and then Apply at the top of the page. 17. Go to Advanced > IGMP Snooping Querier > Configuration. Click Enable and make sure the IGMP Version is set to V2, then click Apply at the top of the page. 18. The Querier IP address should be set to the same IP address as the switch. 5 ONEIP NETWORK CONFIGURATION GUIDE - PAKEDGE MS SERIES 19. Select the VLAN Configuration Tab in the IGMP Snooping Querier menu. 20. On the right side, select the three dots under OPTIONS and choose `Add'. 21. Confirm VLAN 1 is selected and enable `Querier Election Participation'. The VLAN IP can be 0.0.0.0. 22. Then, click Add button. 23. Click the Apply button in the top right corner of the screen. 24. This is all that is needed for a single switch setup. MANUAL VERSION HISTORY V1.0 - 8th February 2024. First version. 6Adobe PDF Library 17.0 Adobe InDesign 19.1 (Windows)