Regulatory Compliance

For Class B AP with adapter:

FCC Compliance Information Statement

The FC logo is a representation of the Federal Communications Commission.

Product Name: Omada Indoor/Outdoor Access Point

Model Number: Festa F41-Outdoor / Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor

Responsible party:

TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• ✔️ Reorient or relocate the receiving antenna.
• ✔️ Increase the separation between the equipment and receiver.
• ✔️ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• ✔️ Consult the dealer or an experienced radio/ TV technician for help.

FCC Rules Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

"To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter."

Product Name: I.T.E. Power Supply

Model Number: T240025-2-POE / T240050-2-POE / T480050-2-POE / T480038-2-POE

Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• ✔️ Reorient or relocate the receiving antenna.
• ✔️ Increase the separation between the equipment and receiver.
• ✔️ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• ✔️ Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2024-11-07

CE Mark Warning

The CE mark indicates conformity with EU directives.

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

OPERATING FREQUENCY (the maximum transmitted power)

• For Festa F41-Outdoor:
  2412MHz–2472MHz(20dBm)
• For Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor:
  2412MHz–2472MHz(20dBm)
  5150MHz–5250MHz(23dBm)
  5250MHz–5350MHz(23dBm)
  5470MHz–5725MHz(30dBm)

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/ce.

RF Exposure Information (EU)

This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20cm from your body.

National Restrictions (EU)

For Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor:

• Frequency band: 5150 - 5250 MHz:
  Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 - 5250 MHz band.
• Frequency band: 5250 - 5350 MHz:
  Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.
• Frequency band: 5470 - 5725 MHz:
  Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.

UKCA Mark

The UKCA mark indicates conformity with UK legislation.

UK Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.

The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca

National Restrictions (UK)

For Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor:

Attention: In Great Britain, the operation in the frequency range 5150MHz - 5350MHz is only permitted indoors.

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

French Translation: L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

For Festa F52-Outdoor:

This radio transmitter (IC: 31152-F52OD / Model: Festa F52-Outdoor) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list below, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

French Translation: Le présent émetteur radio (IC: 31152-F52OD / Model: Festa F52-Outdoor) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste ci-dessous et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

Caution

Professional installation instruction (For Festa F65-Outdoor / Festa F61-Outdoor)

1. Installation personnel

This product is designed for specific application and needs to be installed by a qualified trained person who has RF and related rule knowledge. This product needs to be professionally configured by SDN Controller network service before use.

2. Professional Installation Requirements

National Restrictions (Canada/Hong Kong)

• This device is generally for industrial/commercial use, which only sold to authorized dealers or installers.
• Operation in the 5150-5250MHz is restricted to indoor use only.
• Operation in the 5600-5650-MHz band is prohibited.

For Festa F52-Outdoor:

1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
2. For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
3. For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
4. DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-5600MHz, and 5650-5725MHz.

For Festa F61-Outdoor / Festa F65-Outdoor:

1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
2. DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-5600MHz, and 5650-5725MHz.

Avertissement (Warning - French)

Pour Festa F52-Outdoor:

1. Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
2. Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limitation P.I.R.E.;
3. Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l'exploitation point à point et non point à point, selon le cas.

Les produits utilisant la technique d'atténuation DFS (sélection dynamique des fréquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.

Pour Festa F61-Outdoor / Festa F65-Outdoor:

1. Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
2. Les produits utilisant la technique d'atténuation DFS (sélection dynamique des fréquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.

Radiation Exposure Statement (Canada)

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

French Translation: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음. (This wireless equipment may cause radio interference during operation.)

NCC Notice & BSMI Notice (Taiwan)

注意!

取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。

前述合法通信,指依電信管理法規定作業之無線電通信。

低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

• 針對 Festa F61-Outdoor / Festa F65-Outdoor:
  應避免影響附近雷達系統之操作。
• 針對 Festa F52-Outdoor:
  應避免影響附近雷達系統之操作。
• 高增益指向性天線只得應用於固定式點對點系統。

安全諮詢及注意事項

• 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

RoHS Statement (Substance Content Declaration)

Chinese Text: 清潔本產品之前請先拔掉電源線.請勿使用液體、噴霧清潔劑或濕布進行清潔。

注意防潮,請勿將水或其他液體潑灑到本產品上。

插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。

請勿將本產品置放於靠近熱源的地方.除非有正常的通風,否則不可放在密閉位置中。

不要私自拆開機殼或自行維修,如產品有故障請與原廠或代理商聯繫。

電源供應器应使用在环境温度低於或等於40℃的室內。

限用物質含有情況標示聲明書

備考1. "超出0.1 wt %" 及 "超出0.01 wt %" 系指限用物質之百分比含量超出百分比含量基準值. (Note 1: "Exceeds 0.1 wt %" and "Exceeds 0.01 wt %" refer to the percentage content of the restricted substance exceeding the threshold.)

備考2."○"系指該項限用物質之百分比含量未超出百分比含量基準值. (Note 2: "○" indicates that the percentage content of the restricted substance does not exceed the threshold.)

備考3."—" 系指該項限用物質為排除項目. (Note 3: "—" indicates that the restricted substance is excluded.)

Ukraine Certification (UkrSEPRO)

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

(Product is certified according to the rules of the UkrSEPRO system for compliance with the requirements of normative documents and requirements stipulated by the current legislative acts of Ukraine.)

The EAC mark indicates conformity with Eurasian Economic Union standards.

Safety Information

• The product can only be installed by professional personnel.
• Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid.
• Adapter should be used indoors where the ambient temperature is lower than or equal to 40 °C. Outdoor products are powered through the adapter's output line.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact TP-Link.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Do not use the device where wireless devices are not allowed.
• Adapter shall be installed near the equipment and shall be easily accessible.

General Safety and Operating Instructions

• Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact TP-Link.
• Plug the adapter into the wall outlets with earthing connection through the power supply cord.
• Operating Temperature: -30°C – 70°C (-22 °F – 158 °F )
• This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.
• Please read and follow the above safety information when operating the device. TP-Link cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label

Note: The Equipment marking is at the bottom of the device. Symbols may vary from products.

Mounting Requirements

For safety, TP-Link recommends you to use the original screws in the package when mounting. The following are alternatives to mount the device on the wall:

• Use 2 screws which comply with ANSI B1.1 4#, (5#), 6# standard and are longer than 7mm.

Diagram Description: This diagram shows a screw recess with a large center opening, tapered wings, and a blunt bottom, with all edges relieved or rounded.