User Manual for TAKSTAR models including: X3HH, X3PP, UHF Wireless Microphone, X3HH UHF Wireless Microphone
X3HH UHF wireless microphone - Guangdong Takstar Electronic Co., Ltd.
04 功能示意 ① 电源按键：长按2秒开启或关闭电源；开机状态下，点按进入红外对频； ② 音量旋钮：调整对应通道音量；顺时针旋转逐渐增大音量，逆时针旋转
File Info : application/pdf, 28 Pages, 1.36MB
DocumentDocument/ X3HH/X3PP ..........................................................................................1 Content.................................................................................14 ..........................................................................................2 ....................................................................................2 ....................................................................................2 ....................................................................................2 ....................................................................................3 ....................................................................................4 ..............................................................................4 ..............................................................................4 ........................................................................5 ........................................................................6 ..............................................................................7 .....................................................................7-8 ..................................................................8 ........................................................................8-9 ....................................................................................9 .................................................................................10 .....................................................................11 .................................................................................12 ........................................................................13 01 X3HH/X3PP X3HH&X3PP UHF 400 6828 333 UHF 32 50 USB Type-C AA OK X3HH ...........................2 .................................1 ...............1 .................................1 AA.................................4 ... ... ... ... ... ... ... ... ...1 X3PP ...........................2 .................................1 ...........................1 ...........................2 ...............1 .................................1 AA.................................4 ... ... ... ... ... ... ... ... ...1 02 X3HH/X3PP 470960MHz () FM ID 20MHz 64 300KHz ±0.015% 90dB A+ ±48KHz 80Hz18KHz 95dB A+ 0.5%at 1KHz) -10+40 DC 5V 0.5A -90 dBm() 1.2V/RMS (at 1KHz THD=1%) LxWxH)160X157X33mm 475g 10mW AA 8 DxL)50x236mm 255g 10mW AA 8 LxWxH)100x64x24.5mm 80g 03 X3HH/X3PP 2 RF RF IR Type-C OUT-AOUT-B OUT-AOUT-B 04 X3HH/X3PP CHA CHB IR IR ONOFF "" AA 05 X3HH/X3PP IR CHB AFAFHIGHAF AFLOWAF SET+- "" IR 1/4 2 AA Ø3.5mm 06 X3HH/X3PP CHB RF ACH01-CH32 B CH33-CH64 1. 2AA ""A A 07 X3HH/X3PP 2. B B 2AA 1. Type-C 2. OK 3. 2 08 X3HH/X3PP 4. CHACHB "" 5. CH2 CH CH2 "----"IRIR 10cm-50cm 5 SET2 +- SET2 "----"IRIR 10cm-50cm 5 09 X3HH/X3PP 1 2 3 4 5 6 7 8 9 10 X3HH/X3PP RL2004/108/EGEuropean Low Voltage Directive RL2006/95/EG WEEE(2012/19/EU) (WEEE) FCC15 1 2 11 X3HH/X3PP 12 13 X3HH/X3PP Product.......................................................................................15 Features....................................................................................15 Application .................................................................................15 Product content...........................................................................15 Specification..............................................................................16 Function instruction...............................................................17-21 Front panel...........................................................................17 Rear panel...........................................................................17 Handheld microphone............................................................18 Bodypack transmitter............................................................19 Display screen........................................................................20 Transmitter installation......................................................20-21 Handheld microphone installation..........................................21 Microphone Operation..................................................................22 Frequency matching operation...................................................22-23 Safaty instruction.....................................................................24 The meaning of lcon..................................................................25-26 14 X3HH/X3PP Product Dear Customer, Thank you for purchasing TAKSTAR X3HH&X3PP UHF wireless microphone. Please read the user manual carefully before operation and keep it for reference in future. If you have any questions or suggestions, please contact our local dealer. Features Designed with UHF wireless microphone dedicated frequency band, free from interference from other industrial frequencies 32 sets of channels for adjustment to avoid frequency interference, supporting simultaneous use of multiple sets of microphones Infrared matching to synchronize the channels of the transmitter and the receiver with just one click Long operating range up to 50m in open area, reliable performance USB Type-C interface of the receiver to connect a mobile power supply for outdoor use Two AA batteries to power up the transmitter for long time operation, easy to maintain and replace Independent output and combo out to connect a mixer or a Karaoke amplifier Application Teaching, training, speech, home entertainment, outdoor performance, etc. Product content X3HH Handheld microphone.........2pcs Receiver ..............................1pc Adapterincluding charging cable..................1pc Audio cable ... ... ... ... ... ......... 1pc AA battery ...........................4pcs User manual........................1pc X3PP Bodypack transmitter............2pcs Receiver..............................1pc Adapterincluding charging cable..................1pc Audio cable...........................1pc Headset mic........................1pc Lavalier mic ........................2pcs AA battery ........................ 4pcs User manual........................1pc 15 X3HH/X3PP Specification System Specification Frequency Range470960MHz (frequency band design) Modulation FM Mute Controlpilot frequency ID code Adjustable Range20MHz Frequency Band Qty64 Frequency Band Interval300KHz Frequency Stability±0.015% Dynamic Range90dB A+ Modulation Deviation±48KHz Frequency Response80Hz18KHz S/N Ratio95dB A+ Distortion0.5%at 1KHz) Operation Temperature-10+40 Operation Range50m (open area Receiver Power SupplyDC 5V 0.5A Audio Out: Independent bal XLR and unbal 6.3 combo Sensitivity-90 dBm (wiring test) Audio Out Max Level1.2V/RMS (at 1KHz THD=1%) DimensionLxWxH)160X157X33mm Weight 475g Handheld Microphone Output Power10mW Power Supplytwo AA batteries Operation Time8h DimensionDxL)50x236mm Weight 255g Bodypack Transmitter Output Power10mW Power Supplytwo AA batteries Operation Time8h DimensionLxWxH)100x64x24.5mm Weight80g Note: The data is tested by Takstar laboratory and Takstar has the final interpretation right! 16 X3HH/X3PP Function instruction Front panel Power button: Keep pressing it for 2 seconds to turn on/off the mic. When the mic is on, press it for infrared matching. Volume knob: Adjust the volume of the corresponding channel; turn clockwise to gradually increase the volume, and turn counterclockwise to gradually decrease the volume. Signal LED: Display the working status of the corresponding channel. When the RF is not received, it keeps lighting up red; when the RF is received, it lights up green. During frequency matching, it flashes red and green. IR matching window: Receive infrared matching signal during matching. Rear panel Type-C connector/interface: Connect a power adapter or a mobile power supply. Audio output connector/interface: Connect OUT-A or OUT-B to output the mixed microphone signal; connect OUT-A and OUT-B to independently output the microphone signal. 17 X3HH/X3PP Handheld microphone CHA CHB IR Display screen: Display frequency code, signal channel, microphone signal status, battery power and other information. IR matching window: Transmit infrared matching signal when matching frequency. Power switch: Turn on when the switch is in the "ON" position, and turn off when the switch is in the "OFF" position. Frequency modulation button: It is used to adjust frequency code and match frequency. Refer to the "frequency matching operation" for details. Battery compartment: It is used to install AA batteries. 18 X3HH/X3PP Bodypack transmitter IR CHB AF adjustment: Adjust the sensitivity level. When the AF switch is turned to HIGH, the AF sensitivity is adjusted to high level suitable for lavalier microphones; when the AF switch is turned to LOW, the AF sensitivity is adjusted to low level suitable headset microphones. Display screen: Display frequency code, signal channel, microphone signal status, battery power and other information. Frequency modulation buttons: Include SET, +, and- buttons. It is used to adjust frequency code and match frequency. Refer to the "frequency matching operation" for details. IR matching window: Transmit infrared matching signal when matching frequency. External antenna: 1/4 wave antenna. Power switch: Press it for 2 seconds to turn on/off the microphone, and click/tap it to turn on/off the mute function. Belt buckle: It is used to fix the transmitter. Battery compartment: It is used to install AA batteries. Mute indicator: When the mute function is turned on, the indicator lights up red; when the mute function is turned off, the indicator lights up green. Microphone connector: It is used to connect 3.5mm lavalier microphones or headset microphones. 19 X3HH/X3PP Display screen CHB Signal symbol: Display the status of the microphone RF signal. Battery power: The battery power has three bars, and the number of bars represents the battery power. When the battery is low, the battery symbol flashes. Working frequency: Display the current working frequency code of the microphone. Channel A displays CH01-CH32, and channel B displays CH33-CH64. Signal channel: working signal channel of the microphone. Transmitter installation 1. Install the battery: Press the retractable button to take out the battery compartment, install 2 AA batteries according to the positive and negative polarity marked on the battery compartment (pay attention not to install the batteries reversely), and push the battery compartment into the battery holder of the transmitter until the retractable button is fastened in place with a "click" sound as shown in Figure A. Figure A 20 X3HH/X3PP 2. Insert the lavalier microphone or headset microphone into the microphone connector, and lock it firmly as shown in Figure B. Figure B Handheld microphone installation Open the microphone tail cover counterclockwise, install 2 AA batteries according to the positive and negative polarity marked on the battery compartment (pay attention not to install the batteries reversely), and tighten the microphone tail cover clockwise as shown below. 21 X3HH/X3PP Microphone Operation 1. Connect the power adapter or mobile power supply to the Type-C interface of the receiver. 2. Connect the audio output interface to the microphone input interface of the sound reinforcement equipment (such as mixer, karaoke amplifier) through the audio cable. When the microphone is connected to the sound reinforcement equipment, please adjust the volume of the equipment to the minimum to avoid impact on the equipment when connected. 3. Press the receiver's power button for 2 seconds, and its signal indicattor lights up red, indicating that the power is on. 4. Turn on the power switch of the handheld microphone or bodypack transmitter. When the channel signal indicator of the receiver lights up green, it means that the connection with the corresponding receiver channel (CHA or CHB) is successful; if the connection is not successful, refer to the "Frequency matching operation" for details. 5. When in use, adjust the receiver's volume knob to an appropriate position according to the actual situation to control the microphone's output volume. Frequency matching operation When the product leaves the factory, the frequency has been matched by default. The connection is automatic when the product is turned on. In case of signal interference, you can readjust and match the frequency as follows. 22 X3HH/X3PP Handheld microphone In the power-on state, press the CH button of the handheld microphone for 2 seconds to enter the frequency modulation mode. When the channel on the display screen is flashing, click the CH button to switch the frequency code, and each click switches a frequency code. Press the CH button again for 2 seconds to confirm the frequency code and enter the automatic frequency matching mode with digital scrolling display "----". Align the IR matching window of the handheld microphone with the IR matching window of the receiver in a straight line (the matching distance is recommended to be between 10cm-50cm). Click the power switch of the receiver to enter the frequency matching mode, and the corresponding channel signal of the receiver flashes red and green. After the matching is successful, the receiver lights up green. Note: After the handheld microphone enters the frequency matching mode, please complete the operation within 5 seconds. If the matching fails, please repeat the above steps. Bodypack transmitter In the power-on state, press the SET button of the bodypack transmitter for 2 seconds to enter the frequency modulation mode. When the channel on the display screen is flashing, click the "+" or "-" button to switch the frequency code, and each click switches a frequency code. Press the SET button again for 2 seconds to confirm the frequency code and enter the automatic frequency matching mode with digital scrolling display "----". Align the IR matching window of the bodypack transmitter with the IR matching window of the receiver in a straight line (the matching distance is recommended to be between 10cm-50cm). Click the power switch of the receiver to enter the frequency matching mode, and the corresponding channel signal of the receiver flashes red and green. After the matching is successful, the receiver lights up green. Note: After the bodypack transmitter enters the frequency matching mode, please complete the operation within 5 seconds. If the matching fails, please repeat the above steps. 23 X3HH/X3PP Safety instruction In order to avoid possible personal injury or property damage caused by electric shock, high temperature, fire, radiation, explosion, mechanical hazards and improper use, please read and observe the following items carefully before using the product. 1. When using the product, please confirm whether the power of the connected device matches the power of the product, and adjust the volume of the device. Do not use it for a long time when the power of the product is exceeded or at a high volume to avoid product failure and hearing damage. 2. If there is any abnormality (such as smoke, odor, etc.) during use, please turn off the power switch and unplug the power plug immediately, and then send the product to the dealer for maintenance. 3. If the product needs to use removable batteries, it is strictly forbidden to use batteries with damaged insulation materials. Please do not charge non-rechargeable batteries. 4. Discarded batteries must be placed in designated classified garbage bins, and cannot be used as children's toys or discarded directly to avoid potential safety hazards or environmental impact. 5. If you don't use the product for more than a week, please take out the battery to avoid product damage due to battery leakage. 6. The product and accessories should be placed indoors in a dry and ventilated place. Do not store them in a humid and dusty environment for a long time. Avoid getting close to fire, rain, water, excessive collision, throwing, vibrating the machine and covering the ventilation holes during use, so as not to damage its function. 7. If the product needs to be fixed on the wall or ceiling, please make sure to fix it in place to prevent it from falling down. 8. When using the product, you must abide by the relevant safety regulations. Please do not use the product in the occasions that are clearly prohibited by laws and regulations to avoid accidents. 9. Please do not disassemble, refit or repair the product by yourself to prevent personal injury. If you have any questions or service needs, please contact the local dealer for follow-up. 24 X3HH/X3PP The meaning of lcon According to the test results of RL2004/108/EG and European Low Voltage Directive RL2006/95/EG, the product complies with the limit specified in the directives of the European Community on the integration of the laws of the member states of electromagnetic compatibility. This symbol indicates that according to the WEEE Directive (2012 / 19 / EU) and national laws, this product should not be disposed of together with your household waste, and should be returned to an authorized recycling station of electrical and electronic equipment (WEEE) for recycling, because this type of waste has potential harmful substances that may have a negative impact on the environment and human health. Meanwhile, when this product is disposed of properly, it is conducive to the effective use of natural resources. For more information on where you can place your waste recycling equipment, please contact your local City Office, Waste Management Bureau or Household Waste Treatment Service Department. 25 X3HH/X3PP NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authorty to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 26 GB/T 17276-1998 9T0X3HHS1BCorel PDF Engine Version 14.0.0.701