Trackimo TRKM110-T: The Smart GPS Heavy-Duty Tracker
Product Safety Information
Please read this safety information before you use the device. Following the warnings will help prevent injury to yourself or others and damage to your device. Additional safety warnings may be given for the operation of specific Apps on your device; you should also follow these instructions.
Pictograms and Graphic Symbols
- Read the Safety Information section of this user guide before using this device. Failure to comply with safety warnings can result in serious injury.
- This device is not intended for use by children under the age of 3 years old. If you allow a child to use it, ensure the child is strictly supervised. This device contains small parts which are a choking hazard.
- For body-worn operation, maintain a separation of 5mm.
- Keep away from pacemakers and other personal medical devices.
- Switch off when instructed in hospitals and medical facilities.
- Switch off when instructed in aircrafts and airports.
- Do not take this device near explosive environments.
- Do not use while refuelling or near gas or flammable liquids.
- Do not dispose of this device or its battery in a fire.
- Avoid contact with magnetic media.
- Avoid Extreme Temperatures.
- Do not try to disassemble.
- This device will not communicate with emergency services.
- Only use approved accessories.
- This device may produce a bright or flashing light.
RF Exposure
This device contains a radio transmitter and a receiver. When it is ON, it receives and transmits RF energy.
Specific Absorption Rate (SAR)
Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organisation ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health. The guidelines use a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit for mobile devices is 2 W/kg. The highest SAR value for this device when tested at 0.5cm from the body complied with this limit.
Regulatory Information
The following safety approvals and notices apply in specific regions as noted.
CE Maintenance
- Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- EUT Operating temperature range: -10° C to 55° C.
- The device complies with RF specifications when the device is used at 5mm from your body.
- To prevent possible hearing damage. Do not listen at high volume levels for long periods.
- The SAR limit of EU (CE) is 2.0 W/kg averaged over one gram of tissue. SAR(max) Body is 1.469 W/kg.
Declaration of Conformity (EU)
Trackimo INC. hereby declares that this GPS Tracker is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Information and Statement
This GPS Tracker meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: GPS Tracker (FCC ID: 2AAI6-TRKM110-T) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for when properly worn on the body is 1.231W/kg. This device was tested for typical body-worn operations with the back of the handset kept 5mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 5mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 5mm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Information and Statement (Canada)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) the device must not cause interference, and (2) the user of the device must accept any radio interference, even if the interference is likely to compromise its operation. The US SAR limit is 1.6 W/kg averaged over one gram of tissue. Device types: GPS Tracker (IC: 12317A-TRKM110-T) has also been tested against these values. The highest SAR value declared under this standard for when properly worn on the body is 1.231W/kg. This device was tested for typical body-worn operations with the back of the handset kept 5mm from the body. To maintain compliance with IC requirements, use accessories that maintain a 5mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components. The use of accessories that do not meet these requirements may not comply with IC requirements and should be avoided. Body-worn Operation: This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 5mm must be maintained between the user's body and the handset, including the antenna. Third-party belt clips, holsters and similar accessories used by this device should not contain metallic components. Accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
UKCA
Children may hurt themselves. They may damage the phone or its accessories unconsciously. Phone or accessory in some small parts may be demolished, and there will be danger of be swallowed into their mouths.
Product Handling
You alone are responsible for how you use your device and any consequences of its use. Use of your device is subject to safety measures designed to protect users and their environment.
- Your device has an IP67 water and dust resistance rating. However, the device is not designed for swimming, diving, or prolonged submersion in water. *IP67 tests are carried out in accordance with [IEC 60529]
- Do not expose your device or its accessories to extreme temperatures, minimum -20 and maximum +45 degrees Celsius. Any temperatures below -20 degrees Celsius the display module / battery may have reduced function due to freezing. After recovering to room temperature full function will be regained. Do not leave the device in your car alone, because temperatures in parked cars can exceed this range.
- Do not expose your device or its accessories to open flames or lit tobacco products.
- Do not use your device in a sauna or steam room.
- Do not charge your device while it is wet.
- Do not drop, throw or try to bend your device or its accessories.
- Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories.
- Do not paint your device or its accessories.
- Do not attempt to disassemble your device or its accessories, only authorised personnel must do so.
- Please check local regulations for disposal of electronic products.
- Do not carry your device in your back pocket as it could break when you sit down.
Small Children
Do not leave your device and its accessories within the reach of children under the age of 3 years old or allow them to play with it. They could hurt themselves or others, or may accidentally damage the device. Your device contains small parts with sharp edges that may cause an injury or which could become detached and create a choking hazard.
Demagnetisation
To avoid the risk of demagnetisation, do not allow electronic devices or magnetic media close to your device for a long time. Avoid other magnetic sources as these may cause the internal magnetometer or other sensors to malfunction and provide incorrect data.
Seizures/Blackouts
Use only approved accessories and chargers.
Electrical Safety
Use only approved accessories and chargers. Do not connect with incompatible products or accessories. Take care not to touch or allow metal objects, such as coins or key rings, to contact or short-circuit the battery terminals, charger, and device charging point or any electrical contacts on accessories.
Do not touch your charger with wet hands. Doing so may cause an electric shock.
Do not touch the power cord with wet hands or disconnect the charger by pulling the cord. Doing so may result in electrocution.
Faulty and Damaged Products
Do not attempt to disassemble the device or its accessory. Only qualified personnel should service or repair the device or its accessory. If your device or its accessory has been submerged in water or other Liquid, punctured, or subjected to a severe fall, do not use it until you have taken it to be checked at an authorised service centre.
Battery Handling and Safety (For Products with Non-removable Battery)
The battery in this device is not user removable. Do not make any attempt to remove the battery or disassemble the device to access the battery. Only use the charger supplied, or manufacturer approved replacements intended for use with your device. Using other chargers could be dangerous. Improper use of your device may result in fire, explosion or other hazards. If you believe the battery has been damaged, do not use or re-charge the device and take it to an authorised service centre for testing. Do not puncture or crush the device or allow it to be subjected to any external pressure or force.
Interference
Care must be taken when using the device in close proximity to personal medical devices, such as pacemakers and hearing aids.
- Pacemakers: Pacemaker manufacturers recommend that a minimum separation of 15cm be maintained between a device and a pacemaker to avoid potential interference with the pacemaker.
- Hearing Aids: People with hearing aids or other cochlear implants may experience interfering noises when using wireless devices or when one is nearby. The level of interference will depend on the type of hearing device and the distance from the interference source; increasing the separation between them may reduce the interference. You may also consult your hearing aid manufacturer to discuss alternatives.
- Medical Devices: Please consult your doctor and the device manufacturer to determine if operation of your device may interfere with the operation of your medical device.
- Hospitals: Switch off your wireless device when requested to do so in hospitals, clinics or health care facilities. These requests are designed to prevent possible interference with sensitive medical equipment.
- Aircraft: Switch off your wireless device whenever you are instructed to do so by airport or airline staff.
EXPLOSIVE ENVIRONMENTS
Petrol stations and explosive atmospheres
In locations with potentially explosive atmospheres, do not take this device. Areas with potentially explosive atmospheres include fuelling areas, below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust, or metal powders.
Blasting Caps and Areas
Do not use this device when in a blasting area or in areas posted turn off "two-way radios" or "electronic devices" to avoid interfering with blasting operations.
DISPOSAL AND RECYCLING
This symbol on your device, battery and accessories means these products must be taken to collection points at the end of their life:
- Municipal waste disposal centres with specific bins for these items of equipment.
- Collection bins at points of sale.
They will then be recycled, preventing substances being disposed of in the environment, so that their components can be reused.
General Information
This radio equipment operates with the following frequency bands and maximum radio-frequency power:
- GSM 850/E-GSM 900 MHz: Class 4,33 dBm (= 2 W)
- DCS 1800/PCS 1900 MHz: Class 1, 30 dBm (= 1 W)
- BT (LE): 2402-2480 MHz, 0 dBm.
Made in China
Manufacturer: Trackimo Inc. 680 Central Ave, Cedarhurst, NewYork 11516, USA.
EU Authorised Representative: TRACKIMO CEE Sp. z o.o., ul. Tytusa Chalubiskiego 9 lok. 2, 02-004 Warsaw, Poland.
UK Authorized Representative: Authorised Rep Compliance Ltd., Arc House, Thurnham, Lancaster, LA2 0DT, UK.
Battery
Li-Polymer Battery
SEC 18650
DC 3.7V, 10000 mAh, 1.90Wh
Caution
Use only approved charger. Do not disassemble or modify. Do not short-circuit. Do not dispose of in fire. Do not expose to high temperature (45°C/113°F). Made by EVE Energy CO., LTD. Made in China.
Declaration of Conformity
I hereby declare that the product:
- Description: GPS Tracker
- Type or model name: TRKM110-T
- Brand name: Trackimo
- Hardware version number: UG02 PCB V0.3
- Software version number: UG02 V0.1
satisfies all the technical regulations applicable to the product within the scope of Council Directives 2014/53/EU, 2014/35/EU and 2014/30/EU, and declares that the same application has not been lodged with any other notified body. (Also compliant with UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091)).
Standards Met: EN IEC 62368-1:2020+A11:2020, IEC 62368-1: 2018, ETSI EN 301 489-1 V2.2.3 (2019-11), ETSI EN 301 489-17 V3.2.4 (2020-09), ETSI EN 301 489-19 V2.1.1 (2019-04), ETSI EN 301 489-52 V1.2.1 (2021-11), EN 55032:2015/A11:2020, EN IEC 61000-3-2:2019/A1:2021, EN 61000-3-3:2013/A2:2021, EN 55035:2017/A11:2020, ETSI EN 301 511 V12.5.1 (2017-03), ETSI EN 301 908-1 V13.1.1 (2019-11), ETSI EN 301 908-2 V13.1.1 (2020-06), ETSI EN 301 908-13 V13.1.1 (2019-11), ETSI EN 300 328 V2.2.2 (2019-07), ETSI EN 303 413 V1.2.1 (2021-04), EN 50566: 2017; EN 62209-2:2010/A1:2019, EN 50663: 2017; EN 62479: 2010. (UK equivalents: BS EN IEC 62368-1:2020+A11:2020, BS EN 55032:2015/A11:2020, BS EN IEC 61000-3-2:2019/A1:2021, BS EN 61000-3-3:2013/A2:2021, BS EN 55035:2017/A11:2020, BS EN 50566: 2017; BS EN 62209-2:2010/A1:2019, BS EN 50663: 2017; BSEN 62479: 2010).
All essential radio test suites have been carried out.
GSM
- Frequency Bands: GSM 900: 880 ~ 915 MHz(TX) 925 ~ 960 MHz (RX); GSM 1800: 1710 ~ 1785 MHz(TX) 1805 ~ 1880 MHz(RX)
- Modulation Mode: GMSK for GSM/GPRS; GMSK and 8PSK for EDGE
- Antenna Type: PIFA
- Antenna Gain: GSM 900: -1.5dBi; GSM 1800: -1.5dBi
- Max power: GSM900 Max power:32.62dBm; GSM1800 Max power: 29.82dBm
WCDMA
- Frequency Bands: WCDMA2100: 1920 ~ 1980 MHz(TX) 2110 ~ 2170 MHz(Rx); WCDMA900: 880 ~ 915 MHz(TX) 925 ~ 960 MHz(Rx)
- Modulation Mode: HSDPA:QPSK/16QAM; HSUPA:BPSK; WCDMA: QPSK
- Antenna Type: PIFA
- Antenna Gain: WCDMA 2100:-1.5dBi; WCDMA 900:-1.5dBi
- Max power: WCDMA 2100:22.27dBm; WCDMA 900: 22.23dBm
LTE
- Frequency Bands: FDD LTE Band 1: 1920-1980 MHz (TX), 2110-2170 MHz (RX); FDD LTE Band 3: 1710-1785 MHz (TX), 1805-1880 MHz (RX); FDD LTE Band 7: 2500-2570 MHz (TX), 2620-2690 MHz (RX); FDD LTE Band 8: 880-915 MHz (TX), 925-960 MHz (RX); FDD LTE Band 20: 832-862 MHz (TX), 791-821 MHz (RX)
- Modulation Mode: QPSK/16QAM
- Antenna Type: PIFA
- Antenna Gain: B1: -1.5Bi; B3: -1.5dBi; B7: -1.5dBi; B8: -1.5dBi; B20: -1.5dBi
- Max power: Band 1: 23.26dBm; Band 3: 23.34dBm; Band 7: 23.09dBm; Band 8: 23.01dBm; Band 20: 23.17dBm;
Bluetooth 4.2 BLE
- Frequency Bands: 2402-2480 MHz
- Modulation Mode: GFSK
- Antenna Type: PIFA
- Antenna Gain: -1.5dBi
- EIRP Max power: -4.48dBm
2.4G WIFI(RX)
- Frequency Bands: 802.11b/g/n(20MHz): 2412~2472MHz; 802.11n(40MHz):2422~2462MHz
- Modulation Mode: 802.11b(DSSS):CCK,DQPSK,DBPSK; 802.11g(OFDM):BPSK,QPSK,16-QAM,64-QAM; 802.11n(OFDM):BPSK,QPSK,16-QAM,64-QAM
- Antenna Type: PIFA
- Antenna Gain: -1.5dBi
GPS
- Frequency Bands: 1575.42MHz
- Modulation Mode: BPSK
- Antenna Type: PIFA
- Antenna Gain: -1.5dBi
Notified Body and Manufacturer Information
NOTIFIED BODY
Name: MiCOM Labs Inc
Address: 575 Boulder Court, Pleasanton, California94566 USA
Identification Number: 2280
MANUFACTURER or AUTHORISED REPRESENTATIVE
Address: Trackimo INC. 680 Central Ave, Cedarhurst, New York 11516, USA
This declaration is issued under the sole responsibility of the manufacturer and, if applicable, his authorised representative.
Point of contact:
Signature: Shlomo Shur
Name: Shlomo Shur
Title: CTO
Company: Trackimo INC.
Date: 2022.12.08
