YUHAO
Installation Guide for The Home Depot models including: DY1185-5B, DY1185-52, DY1185-5B Ceiling Fan, DY1185-5B, Ceiling Fan, Fan
大建云中性美国 DY1185T-5 说明书 GC00101435WE（A0版）
File Info : application/pdf, 14 Pages, 9.49MB
DocumentDocumentModel No.: DY1185-5B/52 Ceiling Fan Installation Instructions THANK YOU We appreciate the trust and confidence you have placed in us through the purchase of this ceiling fan.We strive to continually create quality products designed to enhance your home.Thank you for choosing us! Visit www.pmwfan.com for further assistance. Table of contents Table of contents 1 Safety Precautions 2 Warranty 3 Pre-Installation Tools needed 3 Installation kit 4 Blade balancing kit 4 Specification 5 Installation Step 1(Basic assembly of the fan) 6 Step 2 (Ceiling bracket installation ) 6 Step 3 (Wiring) 7 Step 4 (Install remaining parts) 8 Step 5 (Switch on and ceiling fan works) 9 Remote Control Operation 10 TroubleShooting 11 Balancing 12 .1. Safety Precautions The information contained in the following pages has been prepared to ensure your maximum enjoyment of your fan Please remove the fuse or turn off the circuit breaker to cut off the power before installing the fan. Ensure all electrical connections are in compliance with local laws, regulations and national eletrical codes. If you are not familiar with electrical installation and wiring, please hire a qualified electrician or consult the wiring manual. 1. For your safety, all electrical connections and disconnections should be performed by a qualified electrician. 2. Any action performed for the electrical connection of the device must be carried out after ensuring that the general power supply is disconnected,by removing the corresponding fuse or disarming the protective switch in order to ensure total isolation of the power supply. 3. When deciding where to mount the fan, be sure that there is at least 30 inches(76 cm) of space between the fan and any wall or other obstruction that the fan blades could collide with. The greater this distance, the more effective the air flow produced.After the fan is mounted, be sure that the blades are no less than 7ft(2.1 m) above the ground. 4 . The anchor point for the fan must be able to support a weight of at least 100 pounds(45 kg). If mounting on a ceiling junctionbox, be sure that the fan is adequately supported to prevent loosening or turning. 5. The fan's electrical connection must be "grounded" (the fan's ground cable connected to the installation's grounding network) in order to avoid any branching that may be dangerous to people. 6. Do not connect the fan's power supply to any dimmers,potentiometers, or light switches, as it will cause the fan tomalfunction and/or will damage the motor. The fan must be directly connected to a properly protected installation circuit(magnetothermal differential switch with the adequate size for the fan's consumption and technical specifications).Only use the fan's control to turn it on or stop it. 7. It is recommended to not use these types of fans along with gas installations simultaneously in the same room. 8. The fan must be not be moving and must have come to a complete stop before changing its direction of rotation.This will prevent damage to its motor and to the control unit, when applicable. 9. Do not insert anything that could hit the fan's blades into its pathway while it is moving, as this could cause damage to people, can damage the blades, and can offset the balance of the unit, causing vibrations and wobbling. 10. After installing the fan, ensure that all fastenings aresecure and tightened in order to avoid any noise caused by loose elements. 11. Due to the fan's movement, certain fastenings may become loose. Check all fastenings twice per year at a minimum in order to ensure that they are sufficiently tight. If necessary, they must be retightened. 12. The motor housing can be cleaned with a soft brush or a lint-free cloth to avoid scratching the surface. Clean the blades with a lint-free cloth. Important: Turn off the main power supply before starting any maintenance. Do not clean the fans with water or a damp cloth. Note: The important warnings and instructions indicated in this manual are not guaranteed to cover all possible conditions and situations that may occur. It must be understood that common sense, precaution, and care are factors that cannot be included in all products. These factors can and must only be provided by the user who maintains and enjoys this fan. .2. Warranty The manufacturer warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.The manufacturers also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are your responsibility. Damage to any part such as by accident, misuse, improper installation or by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling. Brass finishes of this type give the longest useful life when protected from varying weather conditions. A certain amount of "wobble" is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. We hereby disclaim any and all warranties, including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer. Pre-Installation Tools Needed .3. Pre-Installation Installation kit AA BB CC Part Description AA Blade screw and washer BB Wire nut CC Screws DD Self tapping screw Blade balancing kit DD Quantity 16+1 3 2 4 .4. Pre-Installation Specification A D E B F C LIGHT ON LIGHT OFF WW NW DW Z Z Z G H I Part Description A Bracket B Decorative ring C Body/motor D Light kit E Light cover F Blades Quantity 1 1 1 1 1 5 Part Description G Receiver H Transmitter I Battery Quantity 1 1 2 .5. Installation Step 1(Basic assembly of the fan) æ Remove two screws from bracket, and unscrew the other two (no need to take them out). ç Remove the screws. x 15 Used to fix the fan blades ×3 Used to fix the light kit Remove the screws x 2 è Put the decorative ring into the motor Step 2 (Ceiling bracket installation ) æ Turn off the fan power supply at the circuit breaker box and the wall switch. Failure to disconnect the power supply prior to installation may result in serious injury or death. OFF .6. Installation ç Choose the following installation methods according to the actual situation of the roof. OR Octagon box Solid wood ceiling Step 3 (Wiring) æ Hang the motor on bracket. Make the wire connection in accordance to the wiring diagram provided. Ground wire AC IN N(White) AC IN L(Black) ç Put the receiver into the bracket and arrange the wires .7. Installation Step 4 (Install remaining parts) æ Remove the fan from the bracket hook, lift and rotate the it to make the seven-character slot of the body is hung on the two nails on the Bracket. x 2 Tighten the screws ç Align bumps and grooves and push up the decorative ring. è Align the connected blade with the mounting hole, and then fix it with screws. x 3 .8. Installation é Connect terminal.Then fix the light kit to the main body with screws. ê Installation of light cover. Step 5 (Switch on and ceiling fan works) ON ZZ Z .9. LIGHOTN LIGHOTFF WW NW DW Remote Control Operation Transmitter learning process 1.Insert the 2 pcs of batteries into transmitter. 2.Turn on the power supply to the fan. Within 10 sec, press and hold the "1" and "2" button for about 3 sec. Once the receiver has detected the frequency, receiver will "Beep Beep" twice.Programming process is completed and fan is ready to use. Press and hold for about 3 sec NOTE: The remote control device has already been code matching when it leaves the factory.If the fan is not responding to the transmitter,repeat transmitter learning process. LIGHT ON LIGHT OFF WW NW DW Z Z Z ABOUT THE MEMORY FUNCTION OF LIGHTSPlease wait for more than 3-5 seconds keep this color that you need at first, and then turn off wait for at least 10 seconds turn on again. This light color would be your need. IMPORTANT: The fan can only operate normally after all blades are installed. If the fan is turned on without installing the blades, the receiver will detect that the fan speed is too fast and the fan will automatically stop. Remote Control Holder Installation æ ç AAA 1.5V è LIGHT ON LIGHT OFF é WW NW DW Z Z Z ê ë LIGHT ON Transmitter Function LIGHT OFF Light ON Light OFF Fan Speed (1/2/3/4/5/6) Fan Off WW NW DW Z Z Z Warm light Press and hold: color temperature"K-" Day light Cool light Press and hold: color temperature"K+" Forward/Reverse Sleep Wind Light brightness "+" Light brightness "-" Fan Timer (1hr,3hr,6hr) .10. TroubleShooting WARNING: Make sure the power is off at the electrical panel box before you attempt any repairs. Problem The fan will not start. The fan sounds noisy. The remote control is not working. Solution Check the main and branch circuit fuses or breakers. Check the line wire connections to the fan and switch wire connections in the switch housing. Check to make sure the frequency switches from the remote control and receiver are set to the same frequency. Make sure all motor housing screws are snug. Make sure the screws that attach the fan blade to the motor hub are tight. Make sure the wire nut connections are not rattling against each other or the interior wall of the switch housing. Allow a 24-hour "breaking-in" period. Most noises associated with a new fan disappear during this time. If using the ceiling light kit, make sure the glassware is secured tightly. Make sure there is a short distance from the ceiling to the canopy. It should not touch the ceiling. Make sure your ceiling box is secure and that rubber isolator pads are used between the mounting bracket and outlet box. Do not connect the fan with wall mounted variable speed control(s). Make sure the frequency switches are set correctly. .11. Balancing Wobbling problems during fan operation If the fan body wobbles during its operation, this is not a sign of malfunctioning (even if it wobbles a few centimeters). To reduce wobbling, you can turn off the fan,and: 1.Check that all blades are properly fastened by tightening their screws. 2.Check the distance between each blade and the ceiling. Measurements to the ceiling can be carried out as shown in the following diagram. If variations exist and you have already correctly tightened the screws, check that all blades have the same shape. If any of them have a shape that is visibly different, this may be causing an imbalance during fan operation. If you have completed the previous steps and the wobbling has not resolved,you should apply dynamic balancing with the kit provided, as explained below: 1.Turn the fan on to the highest speed so that the greatest amount of wobbling is produced. 2.Turn off the fan. Select a blade and place a clip on it (see diagram) halfway between the fastening and the far edge of the blade. 3.Turn on the fan and check whether the wobbling has improved or gotten worse.Turn it off once again and if the wobbling has not improved, place the clip on another blade. Repeat this process and determine on which blade it improves the wobbling. 4.Leave the clip on the blade that produces the best results. Move the clip forward or backwards on this blade until finding the position that offers the best results. 5.Afterwards, remove the clip and place one of the weights on the upper part of the center line of the blade at the position where the clip was located. 1 2 3 .12. Ceiling Fan Questions, problems, missing parts? Before returning to the store, visit www.pmwfan.com for further assistance. Retain this manual for future use. Manufacturer: Zhongshan Miaowang Electrical Appliance Co., Ltd. Address: Building C, No.10, Qingfu Road, Henglan Town, Zhongshan City, Guangdong Province,CN Website: www.pmwfan.com Tech Support Telephone: +12092272409 Tech Support Email Address: support@pmwfan.com GC00101435WE A0