Outdoor Adventure Starts Here | This Way Out | Dometic USA
Instruction Manual for DOMETIC models including: DM2652, DM2662, DM2663, DM2672, DM2682, DM2683, DM2852, DM2862, DM2872, DM2882, 3107315.008, 3107315.008 Rocker Switch, Rocker Switch, Switch
REFRIGERATION REFRIGERATION VENTILATION Revision A Form No. 17.2 /22 222 Dometic Corporation RvisionA no 17.2 /22 222 Dometic Corporation EN Rocker Switch Assembly Service Kit Instructions
dometic corporation elkhart, in
File Info : application/pdf, 2 Pages, 167.54KB
DocumentDocumentREFRIGERATION REFRIGERATION VENTILATION EN Rocker Switch Assembly Service Kit Instructions Installer-Provided Parts #6 x 3/8 in. Screw Quantity 2 USA & CANADA Service Office Dometic Corporation 5155 Verdant Drive Elkhart, IN 46516 Service Center & Dealer Locations Visit: www.dometic.com These Service Kit Instructions (SKI) contain important supplementary information or notifications for the Rocker Switch Assembly. It is not intended to provide all information, instruction, and/or safety messaging related to the product. For complete information, refer to the product manuals. The Rocker Switch Assembly is for use with Dometic Americana refrigerators with ventilation fans. Its purpose is to allow the fan to be turned off if the refrigerator experiences a thermal cut-off issue while operating in transit. NOTICE: The rocker switch should remain in the on position while the vehicle is stationary for optimal cooling performance. Failure to follow warning this could result in a failed cooling unit and/or void the warranty. Service Kit Contents Part Number 3107315.008 3107898.003 303937.856 315503.005 3107648.052 3105433.019 Description Rocker Switch Assembly Switch Panel Red Wire Assembly Fuse Holder and 1 A Fuse Service Kit Instructions Wiring Diagram Decal Quantity 1 1 1 1 1 1 Recommended Tools 3/8 in. Screwdriver/Driver Bit Cutter Compatible Refrigerator Models DM2652 DM2663 DM2682 DM2852 DM2662 DM2672 DM2683 DM2862 DM2872 DM2882 1 Explanation of Symbols and Safety Instructions This SKI has safety information and instructions to help you eliminate or reduce the risk of accidents and injuries. 1.1 Recognize Safety Information This is the safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. 1.2 Understand Signal Words A signal word will identify safety messages and property damage messages, and it will indicate the degree or level of hazard seriousness. WARNING Indicates a hazardous situation that, if not avoided, could result in death or serious injury. Revision A Form No. 3107648.052 08/22 | ©2022 Dometic Corporation Révision A Document no 3109736.029 08/22 | ©2022 Dometic Corporation Installation NOTICE: Used to address practices not related to physical injury. IIndicates additional information that is not related to physical injury. 2 Installation WARNING: ELECTRICAL SHOCK AND/OR FIRE HAZARD. Use care when diagnosing and/or adjusting components on a powered unit. Failure to obey this warning could result in death or serious injury. The rocker switch should be installed in an accessible area. Dometic recommends installing it near the bottom vent opening of the refrigerator. q w t r e 1 Switch Panel and Rocker Switch q Switch Panel w #6 x 3/8 in. Screw e Rocker Switch r 0.6 in. (15 mm) t 1.1 in (28 mm) 1. Disconnect the refrigerator from all power sources (120 VAC and 12 VDC). 2. Using the switch panel as a template, cut a rectangular opening in the refrigerator enclosure at the bottom vent area. 3. Insert the rocker switch into the opening of the switch panel and push towards the switch panel until it snaps in place. Rocker Switch Assembly w er t q y u i o a 2 Wiring Diagram q Red Fan Wire w Fan Limit Switch e Red Wire r Rocker Switch t Red Wire with Fuse Holder y 1 A Fuse u 12 VDC + Terminal i 12 VDC Terminal o Black Fan Wire a Fan 4. Attach the red wire to either terminal of the rocker switch. 5. Attach the red wire with the fuse holder to the remaining terminal of the rocker switch. 6. Use the screws to secure the switch panel to the mounting location. 7. Route both wires to the bottom rear of the refrigerator. Remove the fuse from the fuse holder and set aside. 8. Connect the rocker switch wiring according to the wiring diagram. 9. Verify that all the wiring connections are secure and that the wiring will not contact sharp edges or hot surfaces. IKeep the wiring diagram from the service kit with the wiring diagram for the refrigerator. 10. Install the fuse in the fuse holder. 11. Reconnect the power supply. 2 EN