RitFit Power Cage PPC03A

Safety & Precautions

IMPORTANT: READ ALL PRECAUTIONS CAREFULLY BEFORE USING THIS PRODUCT. RETAIN OWNER'S MANUAL FOR FUTURE REFERENCE.

• In case of defective or missing parts, do not use substitute parts or operate the unit in an incomplete form. Contact RITFIT for replacement.
• Additional features may be added during seasonal production and may not be depicted in line art diagrams. Such changes will not affect performance or assembly. Contact RITFIT for clarification during assembly.
• This product is designed for light commercial or home use only. Light commercial use is defined as a location with multiple users but not in a membership setting (e.g., hotels, fire departments, high schools). Commercial use includes locations that accept membership for equipment use.
• This exercise equipment is designed and built for optimum safety. Operator precautions apply when using any exercise equipment. Please note the following safety procedures:
1. Keep children and pets away from this equipment.
2. Always inspect equipment prior to use to assure structural integrity. Some parts may require occasional maintenance due to wear and tear.
3. Lubricate moving parts as needed (monthly is a good rule).
4. One person at a time should use this equipment unless otherwise designed for safety (e.g., spotter stand).
5. If dizziness, nausea, chest pains, or any other abnormal symptoms are experienced, stop the workout immediately and consult a physician.
6. Always use this equipment on a level surface. Do not use outdoors or near water.
7. Keep hands and feet away from moving parts not intended for body contact during use.
8. Do not insert any object into any openings unless it is meant to be inserted (e.g., a pin in a weight stack).
9. Always perform stretching exercises to warm up before using this equipment.
10. Use this equipment only for its intended purpose as described in the manual.
11. Always wear appropriate workout clothing and shoes. Do not wear robes or other clothing that could become caught in the equipment.
12. Consult your physician before beginning any exercise program.
13. For questions, email the customer service team at support@ritfitness.com.

Care and Maintenance

• Inspect and tighten all parts before using the equipment.
• Clean the equipment using a damp cloth and mild non-abrasive detergent. Do not use solvents.
• Examine the equipment regularly for signs of damage or wear.
• Replace any defective components immediately or keep the equipment out of use until repaired.
• Failure to examine regularly may affect the safety level of the equipment.

Warranty

Power Cage Warranty

A. What's Covered Under RitFit LLC's Basic Warranty? Basic Warranty.

B. Who Is Covered? Purchasers for use of the RitFit Power Cage.

C. What's covered? The Basic Warranty covers the cost of all parts and labor needed to repair any item on your power cage that was defective in material, workmanship, or factory preparation when it left the manufacturing plant. RitFit will perform these repairs or adjustments at no charge, using new or remanufactured parts.

D. When It Begins? The Basic Warranty begins on the day of order.

E. When It Ends? The Basic Warranty lasts for 36 months from the date it begins. However, the following items are covered only for 12 months: bolts, nuts, washers, foot covers, J-hooks, and plate storage pegs.

F. What's Not Covered? The standard Basic Warranty applies to defects in material and/or workmanship but does not cover the power cage's matte finish appearance. Maintaining the matte finish is the owner's responsibility. The Basic Warranty does not cover damage caused by environmental factors such as airborne fallout, insect damage, chemicals, salt, and ocean spray. It also does not cover damage caused by hailstorms, windstorms, tornadoes, sandstorms, lightning, floods, and earthquakes. Damage caused by anything impacting the power cage is not covered.

G. How To Contact Us? To ensure you receive the best technical support, visit www.rifitsports.com to register your warranty. Registered warranties provide customers with a profile for easier support and to receive important product notifications. If any parts are missing, worn, damaged, or broken before assembly, or if you need to replace parts, contact support@ritfitness.com.

Before You Begin

Thank you for selecting the versatile RitFit® Power Cage. The RitFit® Power Cage is designed and manufactured to optimize users' workout performance and minimize adjustment or set-up time.

For your benefit, read this manual carefully before using the Power Cage. If you have additional questions, call the Customer Service Department at +1 315 636 0959, 9:00 am - 5:00 pm PST (Mon.-Fri.). Please note the product model number (PPC03A) and serial number before calling to assist with support.

Familiarize yourself with the parts by reviewing the drawing below:

• Pull-Up Bar
• Back
• Left Side Cable Handle
• J-Hook Safety Bar
• Right Side
• Quick Release Plates Storage Tube
• Plate Storage Rack
• Low Row Foot Tube
• Front
• Landmine

Parts List - Fastener and Tools

Fastener Visuals:

• a M10x70 Square Neck Bolt: 28x
• c M10x50 Hex Bolt: 7x
• e M10x25 Hex Bolt: 2x
• b M10x70 Hex Bolt: 6x
• d M8x45 Hex Bolt: 2x
• f M10 Nut: 43x
• g M8 Nut: 2x
• h M10 Washer: 58x
• i M8 Expansion Bolt: 4x
• j Hex Key: 1x
• k Open-ended Wrench: 2x

Parts List - Accessories

Accessory Visuals:

• A J-Hooks Set: 1x
• B Quick Release Plates Storage Tubes Set: 2x
• C Safety Bars Set: 1x
• D Low Row Foot Tube: 1x

Parts List - Main Frame

Main Frame Visuals:

• 1 Left Upright Frame (front): 1x
• 2 Right Upright Frame (front): 1x
• 3 Upright Frame (back): 2x
• 4 Bottom Base Frame: 2x
• 5 Upper Cross Frame: 2x
• 6 Rear Cross Beam: 1x
• 7 Bottom Cross Beam: 1x
• 8 Chrome Pull-Up Bar: 1x
• 9 Plate Holder Frame: 2x
• 10 Band Peg: 4x
• 11 Landmine: 1x
• 12 Bolt Plates: 6x
• 13 Bolt-down Floor Bracket: 4x

Parts List - Pulley System

Pulley System Visuals:

• 14 Rubber Pad: 2x
• 15 Carabiner: 4x
• 16 Pulley: 13x
• 17 Pulley Peg: 12x
• 18 Plate Carriage: 1x
• 19 Pulley Block: 2x
• 20 Low Row Bar: 1x
• 21 Pulley Handle: 2x
• 22 Lat Pull Shaft: 2x
• 23 Cable A: 1x
• 24 Cable B: 2x

Assembly Instructions

Step 1

Parts Used: Bottom Base Frame (4) x2, Bottom Cross Beam (7) x1, Bolt Plates (12) x2, M10x70 Square Neck Bolt (a) x4, M10 Nut (f) x4, M10 Washer (h) x4.

Visual Description: Attach the Bottom Cross Beam (7) to the two Bottom Base Frames (4) using Bolt Plates (12), M10x70 Square Neck Bolts (a), M10 Nuts (f), and M10 Washers (h).

Step 2

Parts Used: Plate Holder Frame (9) x2, M10x70 Square Neck Bolt (a) x4, M10 Nut (f) x4, M10 Washer (h) x4.

Visual Description: Attach the two Plate Holder Frames (9) using M10x70 Square Neck Bolts (a), M10 Nuts (f), and M10 Washers (h).

Step 3 (Two People Required)

Parts Used: Left Upright Frame (front) (1) x1, Right Upright Frame (front) (2) x1, Upright Frame (back) (3) x2, Bolt-down Floor Bracket (13) x4, M10x70 Square Neck Bolt (a) x8, M10 Nut (f) x8, M10 Washer (h) x8.

Visual Description: Attach the Left Upright Frame (1), Right Upright Frame (2), and two Upright Frames (3) to the base assembly using the Bolt-down Floor Brackets (13), M10x70 Square Neck Bolts (a), M10 Nuts (f), and M10 Washers (h). Ensure the knobs on the floor brackets face inward.

Step 4 (Two People Required)

Parts Used: Rubber Pad (14) x2, Plate Carriage (18) x1, Lat Pull Shaft (22) x2.

Visual Description: Place the Rubber Pads (14) onto the designated areas. Insert the Plate Carriage (18) and the two Lat Pull Shafts (22) into their respective positions.

Step 5 (Two People Required)

Parts Used: Upper Cross Frame (5) x1, Rear Cross Beam (6) x1, Bolt Plates (12) x2, M10x70 Square Neck Bolt (a) x4, M8x45 Hex Bolt (d) x2, M10 Nut (f) x4, M8 Nut (g) x2, M10 Washer (h) x4.

Visual Description: Connect the Upper Cross Frame (5) and Rear Cross Beam (6) to the upright frames using Bolt Plates (12), M10x70 Square Neck Bolts (a), M8x45 Hex Bolts (d), M10 Nuts (f), M8 Nuts (g), and M10 Washers (h).

Step 6 (Two People Required)

Parts Used: Upper Cross Frame (5) x1, Bolt Plates (12) x2, M10x70 Square Neck Bolt (a) x4, M10 Nut (f) x4, M10 Washer (h) x4.

Visual Description: Attach the second Upper Cross Frame (5) using Bolt Plates (12), M10x70 Square Neck Bolts (a), M10 Nuts (f), and M10 Washers (h).

Step 7 (Two People Required)

Parts Used: Chrome Pull-Up Bar (8) x1, M10x70 Square Neck Bolt (a) x4, M10 Nut (f) x4, M10 Washer (h) x4.

Visual Description: Install the Chrome Pull-Up Bar (8) using M10x70 Square Neck Bolts (a), M10 Nuts (f), and M10 Washers (h).

Step 8

Parts Used: Pulley (16) x13, Pulley Peg (17) x12, M10x70 Hex Bolt (b) x6, M10x50 Hex Bolt (c) x7, M10 Nut (f) x13, M10 Washer (h) x26.

Visual Description: Attach the Pulleys (16) using Pulley Pegs (17), M10x70 Hex Bolts (b), M10x50 Hex Bolts (c), M10 Nuts (f), and M10 Washers (h).

Step 9

Parts Used: Carabiner (15) x4, Pulley Block (19) x2, Pulley Handle (21) x2, Cable A (23) x1, Cable B (24) x2, M10x25 Hex Bolt (e) x2, M10 Nut (f) x4, M10 Washer (h) x4.

Visual Description: Connect the Carabiners (15), Pulley Blocks (19), and Pulley Handles (21) using Cables A (23) and B (24). Use M10x25 Hex Bolts (e), M10 Nuts (f), and M10 Washers (h) for connections. If a part is too tight, adjust it using the provided bolt as shown in the diagram. Disassemble only one side of Cable A first, then follow the steps to run it through the power cage.

Step 10

Parts Used: Band Peg (10) x4, Landmine (11) x1.

Visual Description: Install the Band Pegs (10) and the Landmine (11) in their designated locations.

Step 11

Parts Used: J-Hooks Set (A) x1, Quick Release Plates Storage Tubes Set (B) x2, Safety Bars Set (C) x1, Low Row Foot Tube (D) x1.

Visual Description: Attach the J-Hooks Set (A), Quick Release Plates Storage Tubes Set (B), Safety Bars Set (C), and Low Row Foot Tube (D) to the power cage.

Warnings

• Keep hands, arms, and feet away from sharp corners and joints of the cage. Keep children away from the cage!
• Weight Plate Diameter: Max 18.1 inches.
• Single Plate Weight: Max 45 lbs.
• Plate Holder Capacity: Each peg Max 165 lbs.
• Misuse of this machine may result in serious injury.
• Read the user's manual prior to use and follow all warnings and instructions.
• Do not allow children under the age of 13 on or around the machine.
• The maximum user weight should be less than 400 lbs.
• For consumer use only; not for commercial use.
• For questions, email the customer service team at support@ritfitsports.com.

Dear RitFit Customers,

Thank you for choosing the RitFit Power Cage with Safety Bar and Plate Holder! Before assembling, please note three important warnings regarding user and product safety. You MUST read these warning labels carefully, as failure to follow them may lead to serious injury!

Dimensions

• Height: 81 in
• Width: 67.3 in
• Depth: 44 in
• Pull-up Bar Height: 85 in
• Base Width: 62.8 in
• Base Depth: 57.5 in

Online Resources

Visit www.ritfitsports.com to:

• Subscribe for a Free Exercise Ebook and Latest Updates.
• Get in touch for support at support@ritfitsports.com.
• Connect on social media @ritfitsports.