Lifespan Kids Slippery Slide User Manual

Product Overview

A line drawing of a children's slippery slide with support legs and handrails is presented on the cover. The manual is for the Lifespan Kids Slippery Slide.

Warning: The disassembled product may contain small parts which pose a choking hazard to children under 3.

Important: This product may contain sharp points and small parts prior to assembly. The owner's manual contains safety, assembly, use and maintenance instructions. This product must be assembled by an adult who has read and understood these instructions. Keep the packaging away from children and dispose of all packaging before use. For the installer and your children's safety, it is important to fully read and understand the instructions and safety hazards before commencing the assembly of the product.

Note: This manual should not be used to guide your purchasing decision. Your product, and the contents inside its carton, may vary from what is listed in this manual. This manual may also be subject to updates or changes. Updated manuals are available through our website at www.lifespankids.com.au.

General Safety Instructions

This product is intended for outdoor, domestic use only.

1.1 Danger for Children

⚠️ WARNING: No eating while using the product.

• Children do not recognize potential dangers from this product. The product must be stored out of reach of children and pets.
• This product may only be used with adult supervision at all times.
• The packaging material is not suitable for children due to choking and suffocation hazards.

1.2 Risk of Injuries

• Do not use the product if it is damaged or defective. If it is damaged or defective, please contact a qualified technician.
• Check the product before each use. Defective parts must be changed immediately as they can impair the function and the safety of the product.
• No more than one person to use the product at the same time.
• Use the product only on even and non-slipping surfaces. Never use it near water and keep sufficient space around for safety.
• Beware of moving parts such as the springs or elastics, which your arms and legs can get caught in. Do not place any objects or body parts in the product's openings.

1.3 Product Damage

• Do not make alterations to the product. Only use original spare parts. Qualified technicians should only carry out repairs – improper repairs can lead to danger for the user. Use this product only as described in this manual.
• Protect the product against high moisture, humidity, high temperature and direct sunlight.

1.4 Assembly Advice

• The assembly of the product must be done carefully and by an able-bodied adult. If in any doubt, ask a technically qualified person.
• Before you start with the assembly, read the instructions carefully.
• Remove all packaging materials and lay down all parts on an open space. This gives you an overview and simplifies the assembly procedure.
• Check with the parts list that all parts are available. Dispose of the packaging material when the assembly is completed.
• Beware that when using tools or doing technical work, there is always a risk of injuries. Assemble the product with care.
• Create a danger-free environment; for example, do not let tools lay around the workspace. Store the packaging material in a way that cannot cause any danger.
• After installing the product according to the instruction manual, ensure all screws, bolts and nuts are correctly installed and tightened and that all joints are secure.
• Reasonable space must be kept between the product and possible sources of danger, such as other equipment, swimming pools, and fences.
• The product must be assembled correctly before use.
• Your play structure must be installed on a flat horizontal surface with a minimum of 2m between it and any structure or obstacle such as a fence, garage, house, tree branches, clothesline, or electric cables.
• Modifications made to the original product shall be carried out according to the instructions of the manufacturer.
• The product must always be used in a well-lit area.
• Do not place anything under the product.
• Use gloves during assembly and disassembly.
• Outdoor products should be equipped with a device that in strong wind conditions avoids displacement due to wind (e.g., steel bars in the ground or loads like sandbags or water bags).
• In certain areas during winter, snow buildup and low temperatures can damage the product. It is recommended to remove snow buildup and store the product indoors.
• Visual inspections every 3 months are strongly recommended to ensure the integrity of the entire product. Replace any parts as necessary.

Safety Instructions

• The safety instructions of the product should always be considered and obeyed.
• Using the product may result in permanent injury such as paralysis, or even death. Falling off the product may lead to injuries, particularly to the back, neck, or head.
• No clothes with hooks or loose parts should be worn or carried during product usage in order to avoid hooks getting caught and causing injury.
• Strong winds can result in the product being blown away or damaged. If strong winds are predicted, the product must be disassembled and moved to a sheltered area or sufficiently anchored down.
• Moving the product whilst assembled may affect the integrity of the frame. Should it be necessary to move the product, please consider the following:
  1. Force to be evenly spaced around the frame to lift the product off the ground.
  2. The product must be carried horizontally.
  3. Use caution whilst moving as it could bend the product frame.
• Users should be familiar with the assembly manual. This manual contains assembly guidance, selected precautionary measures, and recommendations for servicing and maintenance of the product, in order to ensure a secured and fun use of the product.
• It is the responsibility of the owner or the supervisor to guarantee that all users of the product are informed sufficiently of all warning references and safety instructions.

For the supervisor

The supervisor's role is to make sure users are aware of all safety precautions and that these precautions are enforced. When a supervisor is not available, the product may be disassembled or covered to limit access.

• The product can only be used if it is in good condition; worn or damaged parts should be replaced.
• Objects which could be dangerous to the user should be kept away from the product.
• Avoid unauthorized and unsupervised use of the product.
• Do not use the product under the influence of alcohol or drugs (incl. medicines).
• Do not use the product as a jumping platform for other articles.

Playground Surfacing Information

The US Consumer Product Safety Commission (CPSC) estimates that about 100,000 playground equipment-related injuries resulting from falls to the ground surface are treated annually in US hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall onto a shock-absorbing surface is less likely to cause a serious injury than a fall onto a hard surface. Playground equipment should never be placed on hard surfaces, such as concrete or asphalt, and while grass may appear to be acceptable, it may quickly turn to hard-packed earth in areas of high traffic. Shredded bark mulch, wood chips, fine sand, or gravel are considered to be acceptable shock-absorbing surfaces when installed and maintained at a sufficient depth under and around playground equipment.

Table B.1 lists the maximum height from which a child would not be expected to sustain a life-threatening head injury in a fall onto four different loose-fill surfacing materials if they are installed and maintained at depths of 150 mm, 225 mm, and 300 mm.

However, it should be recognised that all injuries due to falls cannot be prevented, no matter what surfacing material is used.

It is recommended that a shock-absorbing material extend a minimum of 1800mm in all directions from the perimeter of stationary equipment such as climbing frames and slides. However, because children may deliberately jump from a moving swing, the shock-absorbing material should extend in the front and rear of a swing with a minimum distance of twice the height of the pivot point measured from a point directly beneath the pivot on the supporting structure.

This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for the equipment in question. The choice of a material depends on the type and height of the playground equipment, the availability of the material in a particular area, and its cost.

Assembly Instructions

Parts List

Tools:

• Hex Wrench (4): 2 pieces
• Wrench (10): 1 piece

Hardware:

• Bolt (E12, Ø6 x 40): 6 pieces
• Bolt (E28, Ø6 x 25): 6 pieces
• Bolt (E29, Ø6 x 20): 2 pieces
• Bolt (E54, Ø6 x 16): 2 pieces
• Nut (G1): 2 pieces
• Bolt (G5, Ø8 x M6 x 12): 6 pieces
• Nut (G6, Ø6): 4 pieces
• Bolt (G13, Ø8 x M6 x 20): 2 pieces
• Washer (Q): 4 pieces
• Washer (L4, Ø6): 14 pieces

Main Components:

• Slide Body (C24): 1 piece
• Support Frame (B227): 2 pieces
• Support Leg (D53): 1 piece
• Side Rail (B496): 2 pieces
• Side Rail (B497): 2 pieces
• Side Rail (B498): 2 pieces
• Side Rail (B499): 2 pieces
• Base Support (B500): 1 piece
• Ladder Rung (C27): 1 piece (used in ladder assembly)

Step 1: Set Up

Attach the slide body (C24) to the support frame (B227) using two E12 bolts and four L4 washers. Connect the support leg (D53) to the frame. Attach side rails (B496) to the base structure using E29 bolts and G13 bolts with L4 washers. Ensure parts are correctly aligned.

Parts used: B227 (x2), B496 (x2), C24 (x1), D53 (x1), E12 (x2), E29 (x2), G13 (x2), L4 (x4).

Step 2: Attach Ladder

Connect the ladder rungs (C27) to the side rails (B497) using E12 bolts and G6 nuts. Ensure the washer (L4) is facing the correct way.

Parts used: B497 (x2), C27 (x1), E12 (x2), G6 (x2), L4 (x2).

Step 3: Secure Ladder

Attach the assembled ladder structure to the main slide body. Use G6 nuts and E12 bolts to secure the ladder rungs (C27) to the frame. Ensure all connections are tight.

Parts used: C27 (x1), E12 (x2), G6 (x2), L4 (x2).

Step 4: Add Support Rails

Attach the remaining side rails (B498, B499) to the base support (B500) and the main structure using E28 bolts and G5 bolts with L4 washers. Ensure all connections are secure.

Parts used: B498 (x2), B499 (x2), B500 (x1), E28 (x6), G5 (x6), L4 (x6).

Step 5: Final Assembly and Safety Checks

Secure the base of the slide using D2 and E54 parts with G1 nuts and Q washers. The diagram shows a 30cm depth requirement for the base supports. Final warnings are displayed.

⚠️ WARNING:

• For outdoor family domestic use only.
• For children from 3 to 7 years (35kg max).
• Must be used under adult supervision.
• The product must not be modified, otherwise risk of serious injury.
• This product must be assembled by an adult. Keep children away during assembly: suffocation danger with small parts.
• Keep additional components; they could be useful for later operation of maintenance.

The product bears the CE mark.

Parts used: D2 (x2), E54 (x2), G1 (x2), Q (x4).

Maintenance

⚠️ WARNING: Please keep for future reference.

Regular maintenance is recommended at the beginning of each season and at regular intervals during the usage season to ensure all main parts/fixings are tightly secured, well-oiled, and intact to avoid failure, injury, or hazards.

General Advice

• Check accessories and the play equipment's structure monthly to prevent falling risks.
• Check and retighten screws, bolts, and all other hardware elements as necessary. Do not over-tighten to avoid damaging the thread or cracking the surrounding wood.
• Check all coverings and bolts for sharp edges and replace when required.
• Lubricate all moving metallic parts.
• When signs of oxidation and/or rust appear on metallic parts, sand rusted areas and tubular members and repaint using a non-lead-based paint when required.
• Where applicable, check swing seats, chains, ropes, and other means of attachment for evidence of deterioration. Replace when required in accordance with the owner's manual.
• If the play structure is disassembled, clearly mark any attached metal plates to prevent accidents. Check all bolt covers and sharp edges and replace them if necessary.

For longer accessory life, store components indoors during winter.

Cleaning

Do not use any abrasive cleansers for cleaning. Use a soft, damp cloth to eliminate dirt and dust.

Warranty

Australian Consumer Law

Many Lifespan Kids products come with a manufacturer's guarantee or warranty. They also come with guarantees that cannot be excluded under the Australian Consumer Law. Consumers are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. Goods are entitled to be repaired or replaced if they fail to be of acceptable quality and the failure does not amount to a major failure. Full details of consumer rights can be found at www.consumerlaw.gov.au.

Full warranty terms and conditions are available on the website: www.lifespankids.com.au/Warranty-Policy-Kids

Warranty and Support

Any claim against this warranty must be made through the original place of purchase. Proof of purchase is required before a warranty claim can be processed. If the product was purchased from the Official Lifespan Kids website, please visit www.lifespankids.com.au/warranty-form.

For support outside of warranty, to purchase replacement parts, or to request repair or service, please visit www.lifespankids.com.au/warranty-form and fill in the Repair/Service Request Form or Parts Purchase Form.