Martec® Australia | Life, enhanced®
Instruction Manual for MARTEC models including: MAFM, MAFML3, MAFM MAFML3 Albatross Ceiling Fan, MAFM MAFML3, Albatross Ceiling Fan, Ceiling Fan, Fan
02 8778 7500 | sales@martecltd.com.au | www.martecaustralia.com.au HOW TO ASSEMBLE Secure the hanger bracket to ceiling beam or a suitable piece of timber inserted between the ceiling beams. Martec Pty Ltd recommends the bracket to be attached with two long screws as supplied within the package.
File Info : application/pdf, 8 Pages, 2.19MB
DocumentDocumentAlbatross Series Ceiling Fan Instruction Book Models: MAFM MAFML3 Thank you for purchasing your MARTEC ALBATROSS Series product. Please read all instructions carefully before assembly and use. IMPORTANT SAFEGUARDS READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. KEEP THE INSTRUCTIONS HANDY FOR FUTURE REFERENCE. IMPORTANT: Always operate the product from a power source of the same Voltage, Frequency and rating as on the product Identication Plate. IMPORTANT: The fan is to be installed so that the blades are more than 2.1 metres above the floor. Avoid contacting moving parts, keep hands, hair and clothing well away from the product while it is in operation. A Luminaire (light fitting) included in the fan packaging may only be fitted to this fan. "This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety." "Young children should be supervised at all times to ensure that they do not play with the appliance." Do not operate any product which has been or appears damaged in any matter or after the product malfunctions. CAUTION: To reduce the risk of electric shock, do not install the product where it can be exposed to rain, moisture or any liquid. Do not use the product for other than its intended use as described in these instructions. This product is intended for normal domestic household use only. The use of accessory attachments other than those recommended by the manufacturer may cause safety hazards. SAFETY Installation of fans must follow S.A.A. standards and meet local Authority regulations. A fully qualified and licensed electrician lawfully MUST carry out installation. Means for disconnection must be incorporated in the fixed wiring in accordance with wiring rules. Fan and light MUST be earthed. Bracket MUST be firmly attached to a solid structure i.e. concrete ceiling, steel structure or timber frame, etc. and MUST be nailed between beams if the timber option is required. ONLY install the remote controller kit that comes supplied by Martec Pty Ltd within package. DO NOT control operation of fan and light with any other remote control than what was approved by Martec Pty Ltd and supplied within this package, as this will void warranty. WARNING Only approved Martec Pty Ltd wall controllers should be used for the operation of our fans. The use of unauthorised controllers will void the warranty. DO NOT mix blades from one fan to another. All blades must be replaced if damaged. Page 1 02 8778 7500 | sales@martecltd.com.au | www.martecaustralia.com.au PARTS LIST DESCRIPTION Motor assembly Instruction manual Screw kit Balancing kit Hanging bracket Remote control kit QUANTITY 1 1 1 1 1 1 Without Light With Light Page 2 02 8778 7500 | sales@martecltd.com.au | www.martecaustralia.com.au HOW TO ASSEMBLE Secure the hanger bracket to ceiling beam or a suitable piece of timber inserted between the ceiling beams. Martec Pty Ltd recommends the bracket to be attached with two long screws as supplied within the package. (See Fig.1.) Place fan into hanger bracket and align Ball Joint Slot with hanger bracket as illustrated. (See Fig.2.) After wiring is completed, attach the canopy to the hanger bracket by pushing upwards and twisting anticlockwise. Locate screws in keyholes and tighten., ensuring canopy is not touching the ball joint. (See Fig.3.) Fig.1 Fig.2 Fig.3 HOW TO INSTALL BLADES Attach the blade to the top of the motor with three blade screws and washers provided. Tighten them securely. Repeat this procedure for all blades. (See Fig.4.) Fig.4 Page 3 02 8778 7500 | sales@martecltd.com.au | www.martecaustralia.com.au HOW TO REMOVE THE SHADE FOR INSTALLING LIGHT BULBS (Version with lights) Turn anticlockwise to remove the shade. (See Fig.5.) Fig.5 CCT (Colour changeable temperature) Simply flick the switch on the LED plate (See Fig.6.) to select the desired colour temperature (3000K, 4000K or 5000K). 3000k 4000k 5000k Fig.6 Page 4 02 8778 7500 | sales@martecltd.com.au | www.martecaustralia.com.au Page 5 02 8778 7500 | sales@martecltd.com.au | www.martecaustralia.com.au WIRING SCHEMATIC DIAGRAM FOR RECEIVER INSTRUCTIONS AND FUNCTIONS OF TRANSMITTER LED indicator light Light ON/OFF (use to switch dim the LED light within 1 second) Speed of the fan (1 high speed 5 low speed) Timing control of the fan Direction of the fan (reverse switch) Fan ON/OFF 12V battery should be used in Transmitter LED indicator light Speed of the fan (1 high speed 5 low speed) Timing control of the fan Fan ON/OFF Direction of the fan (reverse switch) 12V battery should be used in Transmitter Page 6 02 8778 7500 | sales@martecltd.com.au | www.martecaustralia.com.au INSTALLING RECEIVER REMOTE CONTROL IMPORTANT: PAIRING BETWEEN REMOTE AND RECEIVER 1. Turn "ON" the power supply and within 30 seconds press and hold the transmitters "FAN ON/OFF" button for 5 seconds and a "beep" will be heard this will then activate a successful pairing and all functions will work normally. IMPORTANT: pairing initial step must be performed within 30 seconds of power being turned on. 1(a). when pairing multiple fans please ensure the isolation switch or power supply to the first installed fan is turned off prior to pairing futher fans e.g please pair one fan at a time 1 (b). please ensure isolation switch is kept to the ON position, the isolation switch is not to be used as a light switch as this will damage and make the remote recevier inoperable 2. If the transmitter functions are not working please check the battery orientation and power level. Low battery voltage will affect the functions of your transmitter and operation of your fan. Other remote controls nearby using the same frequency may cause interference with the Fans receiver. 3. Please remove batteries from the transmitter if leaving unused for an extended period of time. 4. Remote supports 200w maximum on lighting side. IMPORTANT REMINDERS 1. Please note: Receiver must be correctly installed in the mounting bracket on fan 2. When the transmitter cannot control the receiver, please check the battery has sufficient charge in the transmitter. 3. When the transmitter cannot control the receiver, please check if there is any existence of similar remote controlled products nearby, causing interference with each other. 4. Low power of battery will affect the sensitivity of the transmitter and the signal reception accordingly, must replace if the battery is getting low power. 5. Please take the battery out from the transmitter when leaving unused for a long time, to avoid battery leaks. 6. Supporting 200W lighting power at maximum. 7. Isolation Switch "Must be connected in the line." When power is cute to the unit (via a blackout or otherwise) when power is restored the light will come on. 8. The dimming switch on the light models is operated by turning the light ON/OFF button within 1 second. 9. The light will dim in stages from 24W to 9W to 3W approx. Page 7 02 8778 7500 | sales@martecltd.com.au | www.martecaustralia.com.au