VIVOTEK IB9360-H, IB9380-H Quick Installation Guide
P/N: 625052200G
⚠️ Important Warnings Before Installation
General Safety: The product must be installed and protected in a location that is not easily accessible, and is away from impacts or heavy vibration. Install in high positions (e.g., on a pole or wall) at least 3 meters above the ground.
Compliance: The product should be used in compliance with local laws and regulations.
Mounting: Do not install the product on an unstable mount or surface.
Maintenance: Do not disassemble the camera or perform maintenance tasks when power is connected.
Storage: Before installation, the product should be stored in a dry and ventilated environment.
Accessories: Use only accessories that comply with the technical specifications of the product. Please contact VIVOTEK's certified dealers for power adapters.
Package Contents
Verify the contents of the package:
- Network Camera (IB9360-H / IB9380-H)
- Mounting Bracket
- Screws (M4 x 25)
- Template
- (Other items may be included based on specific model)
Diagram shows the camera, bracket, screws, and a template for marking installation points.
Hardware Installation
Follow these steps for hardware installation:
- Mounting Bracket to Surface: Attach the mounting bracket to a flat surface (e.g., wall, pole) using screws. Diagram shows a bracket being secured to a vertical surface.
- Bracket Assembly: Assemble any parts of the mounting bracket as shown. Diagram illustrates assembling a bracket component, showing a screw passing through a washer into a threaded hole. Hands are depicted tightening the screw. A measurement of 5.5-6.4mm is indicated for a hole size.
- Attach Camera to Bracket: Mount the camera onto the installed bracket. Diagram shows the camera being attached to the bracket, with a curved arrow (?) indicating a rotational motion for securement.
- Camera Orientation: Position the camera on its mount. Diagram shows the camera body on its mount, with an arrow indicating the general direction the camera is facing.
- Secure Camera: Tighten screws to secure the camera to the bracket. Ensure torque does not exceed < 10 kgf-cm. Diagram illustrates attaching the camera to the bracket using screws, with a torque specification of "< 10 kgf-cm" highlighted. An alternative mounting method is also shown.
- Connect Cable: Connect the network cable to the camera's port. Diagram shows a network cable being plugged into the camera's connector.
- Grounding: Connect the grounding wire (20AWG) to the camera's grounding terminal. Diagram shows the rear of the camera with a grounding terminal and a wire labeled "20AWG" being connected. A grounding symbol (⏚) is visible.
- Water Protection: Ensure the camera is protected from rain and moisture. Diagram shows two warning symbols: ? (prohibiting exposure to rain) and ? (prohibiting exposure to moisture).
- Lens Adjustment: Adjust the camera lens for focus. Diagram shows a hand near the camera lens, indicating manual focus adjustment.
- Network Connection: Connect the camera to a network via a LAN cable. Use a PoE (Power over Ethernet) injector that supports IEEE 802.3af. Diagram illustrates the network setup: Camera connected via LAN cable to a PoE injector, which is then connected to a network. A laptop displaying "VIVOTEK Shepherd" software is shown, indicating device management. The Shepherd software interface shows "66 device(s) found" and a browser icon.
- Final Adjustment: Use the provided tool (e.g., Allen key) to adjust the camera's position and angle for the desired view. Diagram shows a hand using an Allen key to loosen a screw on the camera mount, allowing for adjustment, and then tightening it to secure the position.
- Field of View Adjustment: Fine-tune the camera's field of view by rotating and tilting. Two diagrams illustrate field of view adjustments: one shows rotation (?) and tilt controls (represented by circular arrows and a tilt arrow, with icons of a house, lightning, and a person), and the other shows vertical (⬆️⬇️) and horizontal (⬅️➡️) adjustment controls (with icons of a house and trees).
- Secure Mount: Once the desired position is set, tighten the adjustment screws to lock the camera's angle. Diagram shows a hand using an Allen key to tighten a screw on the mounting arm, securing the camera's final position.
Important Note
- The camera is only to be connected to PoE networks without routing to outside plants.
- For PoE connection, use only UL listed I.T.E. with PoE output.
Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Patent: Pat. 6,930,709
Made in Taiwan
Document Status
The full content of this document may be locked and require completion of an order process to access. The Czech text indicates this status and provides reasons for locking, such as protecting the effort involved in creating the manual and preventing unauthorized use by automated systems.
