User Manual for hdtvsupply models including: 4K2K 4x4 and 8x8 HDMI Matrix Switcher with VW seamless switch and EDID, 4K2K Matrix Switcher with VW seamless switch and EDID, 4K2K VW seamless switch and EDID, 4K2K switch and EDID
3 1. Product Introduction This is a new fixed HDMI matrix switcher series with the seamless switch, Video Wall function, EDID management, audio breakouts and the resolution can up to 4K30Hz with scaling funtion
4K 4x4 HDMI Matrix Switcher with Video Wall Function
File Info : application/pdf, 16 Pages, 1.37MB
DocumentDocumentUSER MANUFAixeLd 4K2K 4x4 and 8x8 HDMI Matrix Switcher with VW, seamless switch and EDID Version: V2.0.1 1 Safety Reminder To protect the device and operating personnel from electrostatic discharge, you need to check and ensure that the device is grounding well before the device is powered on. Please observe the following when you install, use, maintain this equipment. Make sure the device ground connection. Important Safety Instructions 2 Warnings of FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and decoder. -- Connect the equipment into an outlet on a circuit different from that to which the decoder is connected. -- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 1 Contents Warnings of FCC ........................................................................................................................... 1 1. Product Introduction ......................................................................................................... 3 2. Features............................................................................................................................ 3 3. Specification...................................................................................................................... 3 4. Connection Diagram .......................................................................................................... 4 5. Packing ............................................................................................................................. 4 6. Panel description............................................................................................................... 5 7. Matrix Switcher control ..................................................................................................... 6 Remote Control .................................................................................................................................6 WEB GUI Browser control .................................................................................................................6 The 3rd Party Control command .....................................................................................................11 2 1. Product Introduction This is a new fixed HDMI matrix switcher series with the seamless switch, Video Wall function, EDID management, audio breakouts and the resolution can up to 4K30Hz with scaling funtion and all ports are HDCP compliant. With the friendly user control methods: IR remote control, 2-Press push buttons with background blue light, WEB GUI/TCPIP/RS232/IR remote control, supports the WEB smart EDID management, this matrix switcher can work with the Blu-Ray Players, Set-Top boxes, Home Theater, and game consoles etc HDMI input sources to route to the HDMI displays, it has been widely used in different audio visual applications. 2. Features The resolution can up to 4K@30Hz inputs and outputs with scaling Supports seamless switching, no black/blue screen during the sources switch Supports the video wall function and bezel corrections Supports the 3.5mm audio embedded and de-embedded Supports smart EDID management Supports RS-232 and TCP/IP Control(WEB GUI, APP), IR remote control Supports the push buttons control with blue lights Supports to rename the inputs and outputs Supports up to 20 scenes 3. Specification Video Resolution HDMI protocol HDCP protocol Color depth Color space EDID HDMI output HDMI output Inputs UHD(3840x2160)/30Hz and under Outputs 4K@30\1080P\720P\1366*768@60 HDMI1.4 HDCP1.4 8/10/12 bit YCbCr,RGB Built-in and output ports learning/copy 4 inputs or 8 inputs 4 outputs or 8 outputs 3 Audio Control Other Audio format Audio sampling Audio baud rate RS232 IR LAN Power Consumption Size Weight Working temp Storage temp Working Humdity PCM 2.1Ch, Dolby Digital, Dolby True-HD, DTS-HD(Only supports 2.1) 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz Up to 16~24-bit DB9 female connector IR receiver RJ45 for the TCP/IP control Power adapter 24V/3A 20W 440*215*44mm 3kg 0~50 -20~ 60 20%-90% 4. Connection Diagram 5. Packing No. Name 1 Matrix switcher 2 DC 24V3A power adapter 3 Remote Control 4 IR remote extension cable 4 Qty Unit 1 Pcs. 1 Pcs 1 Pcs 1 Pcs 6. Panel description Front panel A: LCD screen for the switching, EDID, IP etc information display. B: Power indicator C: IR for the IR remote control D: Inputs and outputs buttons E: Control buttons Back panel A: HDMI input ports B: 3.5mm audio embedded ports C: HDMI output ports D: 3.5mm audio de-embedded ports E: IR extension port for the IR remote control F: RS232 ports for the 3rd party control 5 G: RJ45 port for the WEB GUI/TCP/IP control H: Power supply port I: Grounding 7. Matrix Switcher control This Matrix switcher can support IR remote, WEB GUI browser, TCP/IP/RS232 control, or the front push-buttons control. Remote Control 8x8 4x4 Standby: for the matrix to standby or back to working status Input: 1~8/1~4 HDMI input buttons Clear: Clear all the selected channels Enter: Press to confirm the operations All: to select all the output channels EDID: EDID F1/F2(select the built in EDID or copy/learn from the outputs)EDID press Enter to confirm the EDID Then will need to select the Input channel then press Enter to confirm Output: 1~8/1~4 HDMI output buttons F1/F2: to work with the EDID button WEB GUI browser Control Users also can use the WEB browser to control the matrix switcher, users can have the matrix switcher connected with the PC with the LAN cable directly or have the matrix switcher connected the same network switch. The default IP address of the matrix switcher is 192.168.10.205. After opening the browser, users can type the matrix switcher IP address and press enter: The default user name is admin and the password is admin. 6 After login, it will turn to "Video Matrix" interface, users can do the sources switching, scenes recall and save. On the input and output buttons, users also can view the active ports by the button color, 3 steps for the switching Input button rename: right click on the input button, it will pop-up the window for users to change the names, and option for the Display OSD function. 7 For the output buttons and scenes renaming will the same way to use the right click on the button, it will also pop-up the window: Scenes Save and Recall: It will take 2 steps to Save or Recall the scenes, select the scene number first, and then click "Save" or "Recall" button: 8 Video Wall: users can setup the VW wall, adjust the bezel, VW resolution, or save/recall the VW scenes: Step1: Configure the VW size by entering the columns&rows number, and then hit the Apply button: Step2: Drag the outputs from the right side to this VW boxes accordingly, will need to use the right click to confirm the output after dragged to the VW box, the box edge will in yellow color(Without the right click to confirm, it will be white edge) Step3: After confirmed the outputs in the VW box(all edge in yellow), then drag the input to this VW to finish the switching Video Wall box edge in yellow color means that outputs to this VW are all confirmed(use the mouse right click to confirm after drag the outputs) EDID Management: 9 Output Settings: Audio Settings: users can select audio either from the 3.5mm or from the HDMI Disable means: disable the HDMI sound, but use the 3.5mm embedded audio Enable means to use the HDMI sound For the Audio out: 10 ON means to turn on the HDMI sound, but use the 3.5mm de-embedded still have the sound OFF means to turn off the HDMI sound, but use the 3.5mm de-embedded still have the sound Device is for users to set up the IP address, RS232, or lock the front panel push-button, language or factory default settings: User tap is user the users to change the password, model number and the WEB GUI logo: 11 Upgrade page will need to enter the IP/upload in the browser: TCP/IP/RS232 control details and commands: The default IP IS 192.168.10.205, Port number: 4001 The default RS232 baud rate is 115200, 8, 1, none Function Command Format Function Remark Video Switch AT+HTO2A=MX88,IN$ e.g. AT+HTO2A=MX88,1$ AT+HTO2M=MX88,IN,O1,O2...ON$ e.g. AT+HTO2M=MX88,1,5,6,7,8$ One switch to all output channel +RSPHTO2A=MX88,IN$ One switch to many output Channel +RSPHTO2M=MX88,IN,O1,O2...ON$ Output Setup AT+HTSETAUTORES=MX88,Mode,On$ Mode 1:Auto 0:Manual On:output channel number(1-8) AT+HTSETOUTRES=MX88,Res,O1,O2,On,...$ On:output channel number(1-8) Set output resolution mode +RSPSETAUTORES=MX88,Mode$ Set output resolution +RSPHTSETOUTRES=MX88,Res$ 12 AT+HTTVBLACK=MX88,mod,O1,O2,...On$ On:output channel number(1-8) mod:set TV black (0--1) 0:no black 1:black Set TV black AT+HTTVSET=MX88,On,mod$ On:output channel number(1-8) mod:set TV mute or unmute(1--2) 1:mute 2:unmute set TV MUTE AT+HTOUTMOD=MX88,Mode,On$ Mode 1HDMI 2DVI On:output channel number(1-8) AT+HTEDIDH=MX88,In,On$ In: input chnnel number(1-8) On:output channel number(1-8) Set output mode(DVI or HDMI) +RSPHTOUTMOD=MX88,Mode$ Switch corresponding output's EDID to +RSPHTEDIDH=MX88,In,On$ input AT+HTEDIDINT=MX88,INTn,In$ In: input chnnel number(1-8) INTn: one certain internal EDID number. (2-5) Switch one Internal EDID to certain input's EDID +RSPHTEDIDINT=MX88,In,INTn$ EDID Setup AT+HTEDIDINFOSET=MX88,CHn,ResID,ColorSpace,ColorDepth,A udioCh$ CHn: the input Card's channel number; ResIDn: Resolution ID, ReslDn(1--3);1:720P@60,2:1080P@60,3:4k@30 ColorSpaceN: color space id, ColorSpaceN(1--2);1:RGB,2:YUV Set one input card's certain channel's +RSPHTEDIDINFOSET=MX88,CHn$ edid information ColorDepthN: color depth id;ColorDepthN(1--4);1:8bit,2:10bit,3:12bit,4:16bit AudioChN:Audio ID,AudioChN(1--3);1:2Ch,2:6Ch,3:8Ch Scene Setup AT+HTEDIDUPLOAD=MX88,In$ In, (1--8); When received this command, delay 100ms, send the EDID Upload EDID from WebPage data. AT+HTSCESA=MX88,N$ scene save AT+HTSCERC=MX88,N$ scene recall +RSPHTEDIDUPLOAD=MX88,In$ +RSPHTSCESA=MX88,N$ +RSPHTSCERC=MX88,N$ System Setup AT+HTFACT=MX88$ When No Cn parameter, factory set main control board and GUI Factory setup model. +RSPHTFACT=MX88$ No Cn parameter, if using to factory set main control board and GUI model 13 AT+HTUILOCK=MX88,Val$ Val: 1, locked; 2, Unlocked; GUI Lock AT+HTUARTCFG=MX88,Baud,Databits,Stopbits,Parity$ Baud: 0, 9600; 1, 19200; 2, 38400;3, 57600; 3, 115200; Databits: 0, 8bits; 1, 9bits; Stopbits: 0, 1stopbit; 1, 2stopbits; Parity: 0, none; 1, ODD; 2, even; Audio Setup Video wall Video Border AT+HTAUDSET=MX88,On,Mode$ Mode:Enable(1)/Disable(2) On:output channel number(1-8) AT+HTVIDJNTSA=MX88,N$ N=1~5 AT+HTVDWALLRC=MX88,N$ N=1~5 AT+HTBEZEL=MX16,N1,N2,N3$ N= width ,height , out UART configure Set input card's Audio scene save scene recall Video Border +RSPHTUILOCK=MX88,Val$ AT+HTAUDSET=MX88,Val$ +RSPHTVIDJNTSA=MX88,N$ +RSPHTBEZEL=MX16,N1,N2,N3$ //width,height,out 14macOS Version 12.1 (Build 21C52) Quartz PDFContext, AppendMode 1.1