Instruction Manual for EVVR models including: SS01, In-Wall Relay Switch, SS01 In-Wall Relay Switch, Relay Switch
File Info : application/pdf, 2 Pages, 970.62KB
DocumentDocumentIn-Wall Relay Switch Smart Switch Sub-Assembly Instruction Manual Rev. A-032021 P/N SS01 *Please see separate Smart Relay manual for complete instructions. The Smart Switch Sub-Assembly is an accessory part of In-wall Relay Switch and only functional when connected with the Smart Relay. Complete Accessories Include Instruction Manual Smart Switch ×1 Instruction Manual ×1 TECHNICAL SPECIFICATIONS Model number SS01 Input Voltage Max. Load Power AC 85V~245V AC 110V/300W AC 220V/600W Min. Load Power No limit Supported Switch Type Toggle, Momentary Operating Temperature 0~40°C (32°~104°F) Relative Humidity 5~85% RH Product Size (L*W*H) 33.5mm * 28.2mm * 17.3mm (1.32in. x 1.11in. x 0.68in.) NOTE: `SW1' controls the `L1' `SW2' controls the `L2' Fastening screws SW1: External switch control for load SW2: External switch control for load Panel Connection port L : Power input for live wire L1: Power output for live wire L2: Power output for live wire Wire Connection port Panel Connector Wire ×2 Product Introduction Smart Switch Sub-Assembly is an optional component of the In-Wall Relay Switch when they are used together. The Smart Switch Sub-Assembly is designed to allow mechanical switch panels to work with switch commands from the zigbee network. For example, after turning off the lights with a mechanical switch panel, you can turn on the lights through zigbee network commands. Installation Instructions Caution: Read this manual before attempting to install the device! Using this product in a manner other than intended voids your warranty. Further, Focalcrest is NOT liable for any damage incurred with the misuse of this product. Caution: All installations of this device should be performed by a qualified or licensed electrician! Caution: Product must be installed on a 10A line. One Smart Relay can be connected to one or a series Smart Switch Sub-Assembly (multiple point control). One Smart Switch Sub-Assembly can be connected to two circuits of loads, each of which must use one Smart Relay. Warning: Turn OFF electrical power from the breaker box or electrical service panel before installing or servicing this product. Improper use or installation can cause SERIOUS INJURY, DEATH, or LOSS/DAMAGE OF PROPERTY. Caution: Use this product in an indoor environment. 1 Connect the wires to the switch panel With Smart Switch Sub-Assembly you can control Smart Relay using traditional switch panel. Smart Switch Sub-Assembly compatible with 1/2 gang switch panel, and two Smart Switch Sub-Assemblies can be installed to support 3/4 gang switch panel. The diagram to the right shows the connection of wires. 2 Overall Diagram If the Smart Switch Sub-Assembly and Smart Relay are connected correctly, it should look like diagram below. For more instructions on how to install the Smart Relay, please see the Smart Relay Manual. L N L1 L OUT 1 SW1 L2 SW1 SW2 SW2 L - live wire N - neutral wire N L OUT 2 LOAD 1 LOAD 2 NOTES FOR THE DIAGRAM: LOAD 1 (Black) and LOAD2 (White) are installed using two different connection methods. Please choose the appropriate installation method according to your actual installation environment. In a single switch environment, please choose one of the installation methods to install according to your actual installation environment. 3 Fix Smart Switch Sub-Assembly on a flat, cleaned surface Caution: Before proceeding with this step, please ensure that wires are connected correctly and the devices are operational. Peel off the paper from the adhesive and affix the Smart Switch Sub-Assembly to the recommended location on the box. Turn ON electrical power and check if the light can be turned on. Recommended placement Operating Instructions Note: All operations require a 5-second wait after the Smart Relay power up before use. Set the type of switch panel Note: The default setting is toggle-switch button. To set the switch panel type from toggle to momentary To reset the switch panel type from momentary to toggle Double click momentary switch panel within one second. 1 SEC Change the toggle switch to ON with the lights off, and wait 5 seconds for the lights to automatically turn on. 5 SEC Set the Smart Relay into inclusion/pairing mode with Smart Switch Sub-Assembly Note: The Smart Relay will leave the current network. Working with toggle switch button Working with momentary switch button Quickly toggle the switch button 10 times. Quickly click the switch button 5 times. Troubleshooting Q1 Cannot switch lights on and off normally. The `panel connect wire' from panel to Smart Switch sub- assembly is not properly connected or the wiring of the panel is not correct. 1. Check whether the Smart Relay blue/red LED is on when the load light is on. If the blue/red LED is not on, it may be that the `live IN wire' and `live OUT wire' of the main's power line are not connected properly. 2. If the Smart Relay blue/red LED is on, check whether the panel terminal is properly connected. 3. Please refer to the installation instructions section to check for proper wiring. 4. If only one load is connected to the Smart Switch sub- assembly, please check whether the `power output for live' of the Smart Switch sub-assembly is connected to `L1'. 5. Mechanical switch panel type identification error (Please refer to "4 Set the type of switch panel".). The light turns off automatically after a short Q2 period of time (approximately 2½ minutes or 150 seconds). The power of the light may exceed the maximum power (AC 110V/ 300W, AC 220V/600W). Please check whether the power of the light exceeds the maximum power. After controlling the light wirelessly, the state Q3 of the mechanical switch panel may be different from the actual state of the light. You need to operate the mechanical switch panel twice to restore the light and the panel to the same state. Disposal Instructions This product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Certifications (regional) Warranty Policy For warranty information, please visit https://www.evvr.io/warranty Device will leave the current network and re-enter 30 pairing mode. The load light must be on, at the same SEC time the indicator light will slowly flash blue, wait until pairing is successful or until 30 seconds timeout. Please contact us for any technical issue support@evvr.io Rev. A-032021 P/N SS01Adobe PDF library 15.00 Adobe Illustrator(R) 24.0