Installation Guide for TRAILFX models including: DHS001B, DHS002B, Drop Down Step Bars
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver / Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue. ... 3/26/2020 1:45:59 PM ...
TrailFX DHS001B Drop Down Step Bars For 2015-2021 Chevy Colorado/GMC Canyon
File Info : application/pdf, 4 Pages, 1.76MB
DocumentDocumentTrailFX Drop Down Step Part No. DHS001B / DHS002B Fits: 2015-2019 Chevrolet, GMC / Colorado / Canyon Crew Cab & Ext Cab www.TrailFX.com Product image TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE TAILGATE VENT COVER CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ALIGN THE STEP BARS AS DESIRED AND TIGHTEN ALL M10 FASTENERS TO 30 ft. - lbs., AND THE M8 FASTENERS TO 15 ft.-lbs. 60 min Cutting Not Required Drilling Not Required support@trailfx.com 1 866 638 4870 POLISHED STAINLESS STEEL LIMITED LIFETIME POWDER COATED BLACK 3 YEARS Item 1 2 3 4 5 6 7 8 9 10 PARTS LIST: Qty Part Description Tools Needed 1 Step Bar Driver Side 13 MM SOCKET & WRENCH 1 Step Bar Passenger Side 14 MM SOCKET & WRENCH 3 Mounting Bracket Driver Side 15 MM SOCKET & WRENCH 3 Mounting Bracket Passenger Side RATCHET 12 M8 Bolt TORQUE WRENCH 12 M8 Lock Washer 12 M8 Flat Washer 12 M10 Flange Bolt 12 M10 Flange Nut 12 M8 Nut Clip Mounting Kit Images ITEM 3 Page 1 of 4 ITEM 4 Rev B 03262020 INSTALLATION PROCEDURE Remove Plastic Plugs www.TrailFX.com 1. Remove plastic plugs from rocker panel. 10 5 6 7 8 Figure 1 2. Start at the front driver side of vehicle and grab (2) M8 Nut clips (2) M8 hex head bolts, (2) M8 flat washer, and (2) M8 lock washer to driver mount bracket to rocker panel. Assemble loosely. See Figure 1 and 2. 3. Repeat for center and rear locations. 4. Repeat for passenger side. 5. Grab Driver Side Bar and install loosely to mount brackets with (6) M10 Flange bolts and (6) Serrated Flange Nuts. See Figure 3. 9 6. Repeat for passenger side. 7. Align and adjust the step bars as needed and fully tighten all hardware. 8. See Figure 4 for reference. Page 2 of 4 FIGURE Rev B 03262020 Item 3 DRIVER SIDE SHOWN Item 3 FRONT COMPLETE INSTALLATION www.TrailFX.com Item 3 FIGURE 9 Page 3 of 4 Rev B 03262020 PRODUCT CARE 1. www.TrailFX.com FAQ's 1. Mounting bracket are not getting Installed properly. In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver / Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue. 2. Products are thumping / rattling after installation. Please ensure that all required mounting brackets / hardware's are installed & tighten correctly. Suggest using white lithium / regular grease between the metal to metal contact surfaces. 3. Missing / Excess Hardware. Recheck hardware count as per the part list. 4. Product not installing properly. Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly. Check out these other TrailFX Products!! www.TrailFX.com Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of purchase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product at our option, when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this product voids the warranty. KAO's liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for any incidental or consequential loss or damage. Page 4 of 4 Rev B 03262020