INSTALLATION MANUAL

TOOLS REQUIRED

• Ladder
• Pliers
• Wire Strippers
• Screwdrivers

Scan for Installation Video

APP Control Applicable

PACKING LIST

• A Canopy ×1
• B 4.9-inch Downrod Assembly ×1
• C 7.9-inch Downrod ×1
• D Coupling Cover ×1
• E Fan Assembly ×1
• F Threaded Rod ×1
• G Glass Shade ×1
• H Knurled Nut ×1

INSTALLATION KIT

• AA Mounting Bracket ×1
• BB Wire Nut ×3
• CC Outlet Box Screw ×2
• DD Flat Washer ×2
• EE "R" Pin ×1
• FF Clevis Pin ×1
• GG Gloves ×1
• HH Set Screw ×2
• II Wood Screw ×2
• JJ Remote Holder Anchor ×2
• KK Remote Control ×1
• LL Remote Holder ×1

NOTE:

1. The listed quantity is for installation, extra hardware may be included.
2. Clevis pin (FF) and "R" pin (EE) are pre-installed on downrod assembly (B).

INSTALLATION

1. Disassemble the Downrod Assembly (B)

Remove the "R" pin (EE) and clevis pin (FF) from the downrod assembly (B).

2. Install the Downrod (B/C)

1. Assemble the canopy (A) and coupling cover (D). Route wires from the fan through the downrod (B/C).
2. Loosen the set screw on yoke (do not remove), insert downrod (B/C) into yoke, and align the holes of downrod (B/C) with those of yoke.
3. Pass clevis pin (FF) through the holes of downrod (B/C) and yoke, insert "R" pin (EE) into the hole of clevis pin (FF), and tighten set screws.
4. Fit coupling cover (D) onto fan assembly (E).

3. MOUNT THE BRACKET

1. Pass the power wires through the center hole in the mounting bracket (AA).
2. Fix the mounting bracket (AA) to the ceiling outlet box using outlet box screws (CC) and flat washers (DD).
3. Hang the downrod (B/C) of the installed fan onto the mounting bracket (AA).
4. Rotate the downrod (B/C) until the seat tab in the mounting bracket (AA) is seated in the groove in the downrod ball.

4. CONNECT THE WIRES

1. Connect the wires from the fan to the house supply wires with wire nuts (BB), ground wire (green, green/yelow, or bare copper) to ground wire, neutral wire (white) to neutral wire, and hot wire (black) to hot wire. Wrap the connection with electrical tape.
2. Spread apart the wires so that the hot wires are on one side of the outlet box and the neutral wires are on the other side.

NOTE: This fan only needs one set of input wires (black, white, and ground wire). Both of the fan and lights will be controlled by the remote controller. This fan can only be connected to an on/off switch if you have one, not a dimmer switch.

5. INSTALL THE CANOPY

1. Loosen canopy screw from mounting bracket (AA), but do not take off.
2. Push canopy (A) upwards, allowing canopy screw to pass through the hole in canopy.
3. Rotate canopy clockwise so that it is caught by canopy screw and does not fall down.
4. Tighten canopy screw to secure canopy.

6. INSTALL THE Glass Shade

Tighten the threaded rod (F) to the appropriate length, then secure it with the hex nut. Warning: Avoid excessive rotation to prevent wire damage.

Secure the glass shade (G) to the fan assembly (E) using a knurled nut (H).

INSTALL THE REMOTE HOLDER

1. Insert 2 batteries before using: AAA 1.5V battery x 2pcs (not included).
2. Mark and drill screw holes in the wall, then insert the remote holder anchors (JJ).
3. Use wood screws (II) to fix the remote holder (LL) onto the wall.

REMOTE CONTROL INSTRUCTIONS

• ON/OFF: Turn off fan and light.
• ALL OFF: Turn on/off the light.
• Light Color Switch: Quick switch of the light color: Yellow Light → White Light → Natural Light
• Brightness Adjustment: Adjust the brightness of the light.
• Color Temperature Adjustment: Adjust the light color temperature.
• Night Mode: Night mode, lights will be dimmed when press this button.
• Fan Speeds: Fan speeds 1 through 6.
• F/R: Fan moves forwards or reversely.
• Natural Wind Mode: Fan speed automatically adjusts.
• FAN OFF: Turn off the fan.
• 2H: Timing for 2 hours for the fan.
• SETUP: Remote signal pairing.

NOTE: Please insert 2 batteries before using. AAA 1.5V battery x 2pcs (not included)

Remote Signal Pairing: If the remote control loses the signal from the fan, press and hold the SETUP button right after the fan is powered on from the wall switch. After the fan flashes or beeps, it means the pairing has been successful.

APP CONTROL INSTRUCTIONS

Install the "FanLamp Pro" app from Google Play, Apple App Store, or other app stores by scanning the QR code or searching for the app name. Ensure that your phone is connected to the internet and Bluetooth enabled.

• Pairing: Click the Pair button within 5 seconds after turning on the fan from the wall switch. Once the fan flashes or beeps, it has been successfully paired with your phone and can now be controlled through the app.
• Fan Speed: Slide the slider to change the fan speed.
• Light Brightness: Slide the slider to change the brightness of the light.
• White Light: Quick switch for "White" light color.
• Yellow Light: Quick switch for "Yellow" light color.
• Natural Light: Quick switch for "Natural" light color.
• Night Mode: Dim the lights.
• Fan Forward: Fan moves forward.
• Fan Reverse: Fan moves reversely.
• Wind Direction: Change the direction of the wind. (Not supported)
• Timing: Timing the fan.
• Natural Wind: The fan speed will change automatically when you use this function.
• Sleeping Wind: (Not supported)
• Light On/Off: Turn on/off the light.
• Fan On/Off: Turn on/off the fan.
• Unpairing: Click the unpair button within 5 seconds after turning on the fan. Once the fan flashes or beeps, it has been successfully unpaired from your phone.