DocSmart CORDLESS CHAIN SAW

Please read the manual carefully before use.

Introduce

The DocSmart mini cordless chainsaw features an 8-inch and a 6-inch 2-in-1 guide plate design that allows you to adjust the size of the chainsaw at any time to your work needs. Our mini cordless chainsaw for cutting trees is equipped with powerful 2*2000mAh rechargeable batteries that can provide longer battery life. It is perfect for gardening pruning, shrub pruning, and logging.

What's in the Box

The 8-inch Guide Plate and 8-inch Chain are already preinstalled on the chainsaw.

• Electric coarse branch
• Battery
• Carrying case
• 6-inch Chain
• 6-inch Guide Plate
• Charger
• Brush
• Sharpener
• Glasses
• Grip
• User Manual
• Wrench
• Gloves

Operation

Structure

The chainsaw consists of the following parts:

• Chain
• Guide plate
• Knob
• Guide plate cover
• Baffle
• Oiler lid
• Brushless motor
• Security Button
• Switch
• Battery

Steps for usage

1. Install the guide plate to the host. Ensure the guide plate screw hole is flush with the first screw post.
2. Notice: When installing the guide plate, make sure that the adjusting block gets stuck into the positioning adjusting hole at the end of the guide plate.
3. To remove the guide plate: loosen the compression button, remove the side cover, and then carefully remove the guide plate.
4. Install the chain. First, load the chain into the guide plate, ensuring the middle guide tooth fits into the guide plate guide slot.
5. Notice: The chain blade should face forward. The charging chainsaw has a device to adjust the tensioning of the chain.
6. Turn the knob on the guide plate cover to align the guide plate adjusting screw column boss with the first screw hole.
7. Align the convex points of the adjusting screws on the guide plate cover with the guide plate holes to install the guide plate cover.
8. Turn the knob on the guide plate cover clockwise. Pull the chain down while turning the knob. The chain will rebound quickly when you loosen the chain.
9. Use a socket wrench to tighten the outer hexagonal nut, and then screw the screw into the hole of the guide plate cover.
10. Unscrew the oiler lid, pour the lubricating oil into the oiler, and tighten the oiler lid. (The product does not provide lubricating oil).
11. Insert the battery into the machine.
12. Press the switch to start the machine.

Operating Instructions

1. Please wear suitable clothing and work gloves when using this mini chainsaw.
2. Before each use, ensure the belt is running normally. The start/off switch and safety switch must be available for normal use. When loosening the start switch, the power must be turned off. If the switch is damaged, stop using the device. Ensure the voltage of the power supply is consistent with the voltage on the nameplate. The risk of injury can be reduced by wearing protective devices and ensuring that the devices are functioning properly.
3. Confirm the frequency of the operation to ensure that the operation is in the best condition.
4. To save the battery and ensure the best service life of the electric chain saw, do not let the machine overload. Avoid cutting dry and wet branches with a diameter of more than 130mm.
5. When cutting, to stop the operation, turn off the power switch and detach the battery pack.
6. When the device is running, keep your other hand at least 15cm away from the cutting area of the blade, and do not place your hand near the cutting edge.
7. Do not use this equipment to force larger branches, as this may cause the blade to deform and make the pruning stick.
8. In cold or humid weather, to protect the battery pack, place it under waterproof clothing. Do not use this equipment in rainy days.
9. After daily use, it is recommended to disconnect the connection between the pruning number and the battery pack, turn off the power switch, and store them in the matching tool box.
10. If the user feels the electricity is not enough or the cutting is not smooth enough, check if the electricity is exhausted or the blade is dull.

Safety Warnings

Charing the battery

1. Do not expose the battery to extreme conditions such as high temperature or shock. Otherwise, it will cause personal injury due to the leakage of the electrolytic solution.
2. Before charging, check that the surface of the battery is clean and dry.
3. The battery of this product is not fully charged before delivery. Therefore, it must be sufficiently charged before the first use.
4. Do not charge the battery for long periods of time, and do not run the battery completely out of power, otherwise it will damage the battery.
5. The Essential Security Department does not cover failures due to incorrect use.
6. If the battery's sufficient electricity is significantly shorter, it must be replaced if the battery is exhausted.
7. The user can only use the battery pack manufactured by the original equipment operated by the customer center.

Battery protection

1. Maintain charging temperature between 32°F-113°F (0°C-45°C) and battery pack discharge temperature between 14°F (-10°C) and 140°F (60°C).
2. Place the charger in a room between 50°F (10°C) and 71.6°F (22°C), and prevent moisture from entering.
3. Ensure the power is consistent with the rated values on the charger and adapter.
4. When the red light is on the charger, it indicates that the battery is charging. The green light indicates that the charge is completed. The average charge time is 2 hours.
5. When charging is complete, disconnect the connector from the power source and then disconnect the connector and battery.
6. To ensure that the battery is fully charged, avoid exposing it to extremely hot or cold environments.
7. If the equipment will not be used for a long time, please remove the battery before storage.
8. The batteries and chargers must be placed in the instrument box to prevent heat, dust, and moisture from entering. Check if the switch is off.
9. Recommended storage temperature is 32°F-86°F (0°C -30°C) for longer storage time.
10. The distance between the battery and combustible materials must be kept beyond 1.5m.
11. To ensure the service life of the equipment and prevent its degradation, store it in a fully charged state. When not in use, charge and discharge the battery at least once a month.

Maintenance

1. To ensure safe use, only original parts can be used.
2. Please close the equipment before starting the chainsaw repair. Store the battery in a safe package.
3. Wear hand protection when touching safety blades. This can avoid sharp blade scratching the user. Follow-up cleaning and maintenance must be carried out regularly. This ensures long-term and reliable operation of the equipment.

Clearness

1. Do not spray the equipment with water or immerse it in water, otherwise, it may cause electric shock. Keep the ventilator, motor room, and equipment handle clean. Use a damp cloth or brush cleaner.
2. Do not use a bay cleaner. Otherwise, it may cause permanent failure of the equipment. Please clean the blade carefully after each use.
3. Use an oily cloth to wipe the blade and absorb the metal to protect it from rust.
4. After 8 hours of continuous operation, please remove debris such as dust from the front turbulent cover plate of the equipment.
5. Use the sharpener to sharpen the chain.

Frequently Asked Questions

1. Why didn't the chainsaw turn on?
   Please charge the battery immediately when you receive the product to avoid battery power consumption due to long-distance transportation. If the product cannot be turned on, please charge it for 1-2 hours before turning it on.
2. Can you cut screws and metal with this?
   The correct tool to cut metal is a 'Grinder' with the appropriate blade, not a Chainsaw. Using a chainsaw on metal can cause severe injury.
3. Why does the chain pop off?
   Adjust the chain tension.
4. Does the on/off button have to be pressed at all times to operate the saw?
   Yes, there is an on button that must be pressed while operating the chainsaw.
5. How do I remove the battery?
   Depress the red button and slide it forward, in the opposite direction of how you slide it on.

Specification

Warranty

Your product enjoys a 1-year limited warranty. You can request a product replacement or a refund for quality problems caused by non-human reasons.

How to Activate the warranty?

Please feel free to contact us:

• Email: support@docsmarts.net
• Subject: #Activate the Warranty#
• Amazon Order Number: XXX-XXXXXXX-XXXXXXX
• Call: 1-888-980-8556
• Amazon Message

We will get back to you within 1 business day.

UK CE FC Recycling Symbol