FAQ - PLANET TechnologyDownloads - Support - PLANET Technology
Installation Guide for Planet Technology models including: IGS-5225-4T2S, IGS-5225-4P2S, IGS-5225-4UP1T2S, IGS-5225-8P4S, IGS-5225-8P4S-12V, IGS-5225-8P2T2S, IGS-5225-8P2T4S, IGS-5225-4T2S Industrial L2 Multi-Port Full Gigabit Managed Ethernet Switch, Industrial L2 Multi-Port Full Gigabit Managed Ethernet Switch, L2 Multi-Port Full Gigabit Managed Ethernet Switch, Multi-Port Full Gigabit Managed Ethernet Switch, Full Gigabit Managed Ethernet Switch, Gigabit Managed Ethernet Switch, Managed Ethernet Switch, Ethernet Switch, Switch
IGS-5225-4T2S - L2 Ring Managed Gigabit Ethernet Switch - PLANET Technology
IGS-5225-4T2S L2 Industrial 4-Port 10/100/1000T 2-Port 1G/2.5G SFP Managed Ethernet Switch - Planet Technology USA
Support - PLANET Technology
File Info : application/pdf, 20 Pages, 1.78MB
DocumentDocumentIndustrial L2+ Multi-Port Full Gigabit Managed Ethernet Switch IGS-5225-4T2S/IGS-5225-4P2S/IGS-5225-4UP1T2S IGS-5225-8P4S/IGS-5225-8P4S-12V IGS-5225-8P2T2S/IGS-5225-8P2T4S Quick Installation Guide Table of Contents 1. Package Contents...................................................................... 3 2. Requirements............................................................................ 5 3. Wiring the Power Inputs ............................................................ 6 3.1 Grounding the Device.......................................................... 8 4. Terminal Setup.......................................................................... 9 4.1. Logging on to the Console ..................................................10 4.2 Configuring IP address .......................................................11 5. Starting Web Management ........................................................13 5.1 Logging in to the Industrial Managed Switch ........................13 5.2 Saving Configuration via Web .............................................16 6. Recovering Back to Default Configuration ...................................17 7. Customer Support ....................................................................20 1. Package Contents Thank you for purchasing PLANET L2+ Industrial Managed Switch, IGS-5225 Series. The number of the ports of these models is as follows: GbE Copper Ports PoE Ports GbE SFP Ports IGS-5225-4T2S 4 - 1G/2.5G: 2 IGS-5225-4P2S 4 at/af: 4 2 IGS-5225-4UP1T2S 5 IGS-5225-8P4S 8 IGS-5225-8P4S-12V 8 IGS-5225-8P2T2S 10 IGS-5225-8P2T4S 10 at/bt: 4 at/af: 8 at/af: 8 at/af: 8 at/af: 8 2 1G: 2 1G/2.5G: 2 1G: 2 1G/2.5G: 2 1G/2.5G: 2 1G: 2 1G/2.5G: 2 "Industrial Managed Switch" mentioned in this Quick Installation Guide refers to the above models. 3 Open the box of the Industrial Managed Switch and carefully unpack it. The box should contain the following items for each model of the Industrial Managed Switch: The Industrial Managed Switch Quick Wall Installation Mounting Guide Kit DB9 to RJ45, RS232 Console Cable RJ45 Dust Cap SFP Dust Cap IGS-5225- 5 2 4T2S IGS-5225- 5 2 4P2S IGS-5225- 6 2 4UP1T2S IGS-5225 9 4 -8P4S IGS-5225- 9 4 8P4S-12V IGS-5225- 11 2 8P2T2S IGS-5225- 11 4 8P2T4S If any of these are missing or damaged, please contact your dealer immediately. If possible, retain the carton including the original packing materials to enable you to repack the product in case there is a need to return it to us for repair. 4 2. Requirements The Industrial Managed Switch provides remote login interface for management purposes. The following equipment is necessary for further management: z Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/ IP Protocols. z Workstations are installed with Ethernet NIC (Network Interface Card) z Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-toRS232 converter. The above Workstations have been installed with terminal emulator, such as Hyper Terminal included in Windows XP/2003, putty or tera term. Serial cable -- one end is attached to the RS232 serial port, while the other end to the console port of the Industrial Managed Switch. z Ethernet Port Connection Network cables -- Use standard network (UTP) cables with RJ45 connectors. The above PC is installed with Web browser. Note It is recommended to use Internet Explorer 8.0 or above to access the Industrial Managed Switch. 5 3. Wiring the Power Inputs The Upper Panel of the Industrial Managed Switch comes with one 6-contact terminal block. Please follow the steps below to insert the power wire. 1. Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1, or Contacts 5 and 6 for Power 2. IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S: DC 48~56V DI0 DI1 DO0 DO1 GND GND 1 2 3 4 5 6 Max. Fault Alarm Loading: 24V, 1A 1 2 3 4 5 6 PWR1 Alarm PWR2 DC Input: 48-56V , 6A max. Figure 3-1: IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S Upper Panel IGS-5225-8P4S-12V: DC 12~54V DI0 DI1 DO0 DO1 GND GND 1 2 3 4 5 6 Max. Fault Alarm Loading: 24V, 1A 1 2 3 4 5 6 PWR1 Alarm PWR2 DC Input: 12-54V , 6A max. Figure 3-2: IGS-5225-8P4S-12V Upper Panel 6 IGS-5225-4T2S: DC 12~48V, AC 24V Max. Fault Alarm Loading: 24V, 1A 1 2 3 4 5 6 V1+ PWR1 V2+ Alarm PWR2 DC Input: 12-48V , 1.7A max. AC Input: 24V , 1A max. Figure 3-3: IGS-5225-4T2S Upper Panel IGS-5225-4P2S: DC 48~56V Max. fault loading: 24V, 1A 1 2 3 4 5 6 DC Input: 48-56V , 3.5A max. V1+ PWR1 V2+ Fault PWR2 Figure 3-4: IGS-5225-4P2S Upper Panel IGS-5225-4UP1T2S: DC 48~56V DI0 DI1 DO0 DO1 GND GND 1 2 3 4 5 6 Max. fault loading: 24V, 1A 1 2 3 4 5 6 PWR1 Fault PWR2 DC Input: 48-56V , 6A max. Figure 3-5: IGS-5225-4UP1T2S Upper Panel 7 2. Tighten the wire-clamp screws for preventing the wires from loosening. 123 V+ VPower 1 456 V+ VPower 2 IGS-5225 Series Positive (+) Pin Pin 1/5 Negative (-) Pin Pin 2/6 Note 1. The wire gauge for the terminal block should be in the range from 12 to 24 AWG. 2. Please check the wire AWG Ampere specification before connecting PLANET Industrial Managed Switch. Caution PWR1 and PWR2 must provide the same DC voltage for power load balance while operating with dual power input. 3.1 Grounding the Device Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. Earth Ground DI0 DI1 DO0 DO1 GND GND 1 2 3 4 5 6 Max. fault loading: 24V, 1A 1 2 3 4 5 6 PWR1 Fault PWR2 DC Input: 48-56V , 6A max. 8 4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type serial (console) port of the Industrial Managed Switch. The console port of the Industrial Managed Switch is DCE already, so that you can connect the console port directly through PC without the need of null modem. IGS Industrial Managed Switch Console 115200,N,8,1 PC/Workstation with Terminal Emulation Software Console Port 115200,N,8,1 RJ45 to DB9 RS232 Cable Serial Port A terminal program is required to make the software connected to the IGS-5225 series Industrial Managed Switch. 1. Run terminal program on the OS. 2. When the following screen appears, make sure that the COM port should be configured as: z Baud: 115200 z Parity: None z Data bits: 8 z Stop bits: 1 z Flow control: None 9 4.1. Logging on to the Console Once the terminal has been connected to the device, power on the Industrial Managed Switch and the terminal will display "running testing procedures". Note The following terminal configuration of the IGS5225-4UP1T2S is taken for an example. Then, the following message asks to log in user name and password. The default user name and password are shown as follows and the login screen in Figure 4-1 appears. User name: admin Password: admin Figure 4-1: Console Login Screen The user can now enter commands to manage the Industrial Managed Switch. For a detailed description of the commands, please refer to the following chapters. Note 1. For security reason, please change and memorize the new password after this first setup. 2. Only accept command in lowercase letter under console interface. 10 4.2 Configuring IP address The Industrial Managed Switch is shipped with default IP address shown below: IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedure as follows: Display of the current IP Address 1. At the "#" prompt, enter "show ip interface brief". 2. The screen displays the current IP address shown in Figure 4-2. Figure 4-2: IP Information Screen Configuration of the IP Address 3. At the "#" prompt, enter the following command and press <Enter> as shown in Figure 4-3. IGS-5225-4UP1T2S# configure terminal IGS-5225-4UP1T2S (config)# interface vlan 1 IGS-5225-4UP1T2S (config-if-vlan)# ip address 192.168.1.100 255.255.255.0 The previous command would apply the following settings for the Industrial Managed Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 11 Figure 4-3: Configuring IP Address Screen 4. Repeat step 1 to check if the IP address has changed. Store the current switch configuration 5. At the "#" prompt, enter the following command and press <Enter>. # copy running-config startup-config Figure 4-4: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Managed Switch through the new IP address. Note If you are not familiar with the console command or the related parameter, enter "help" anytime in console to get the help description. 12 5. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Industrial Managed Switch is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0. IGS Industrial Switch IP Address: 192.168.0.x RJ45/UTP Cable IP Address: 192.168.0.100 Figure 5-1: IP Management Diagram 5.1 Logging in to the Industrial Managed Switch 1. Use Internet Explorer 8.0 or above for Web browser and enter IP address https://192.168.0.100 (the factory-default IP address) to access the Web interface. 2. When the following dialog box appears, please enter the default user name "admin" and password "admin" (or the password you have changed before) as shown in Figure 5-2. 13 Default IP Address: 192.168.0.100 Default User Name: admin Default Password: admin Figure 5-2: Login Screen 3. After entering the password, the main screen appears as shown in Figure 5-3. Figure 5-3: Web Main Screen of Industrial Managed Switch 14 The Industrial Managed Switch Menu on the top and left of the Web page lets you access all the functions and status the Industrial Managed Switch provides. The Switch Menu always contains one or more buttons, such as "System", "Switching", "QoS", "Security", "PoE", "Ring", "ONVIF" and "Maintenance". Figure 5-4: Switch Menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user manual for more. Note If you are not familiar with Switch functions or the related parameter, press "Help icon" like the following anytime on the Web page to get the help description. 15 5.2 Saving Configuration via Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot. 1. Click the Save icon on the top Switch Menu bar. Figure 5-5: Save Config -- Hot Key 2. Press the "Save Configuration" button. 3. Or the other way to save the setting is to Click Maintenance, Save Startup Config. Figure 5-6: Save Config -- Maintenance 16 6. Recovering Back to Default Configuration To reset the IP address to the default IP address "192.168.0.100" and the user password to factory default mode (default password is admin), press the hardware reset button on the front panel for about 10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx and default password. Be noted that all the previous setups will be disappeared after the factory default reset is made. P1 P2 Alarm Ring R.O. Reset 115200,N,8,1 Reset 1G/2.5G LNK/ACT 6 5 Figure 6-1: IGS-5225-4T2S Reset Button 17 Reset P1 P2 Fault Ring R.O. Reset PoE Usage 120W Console 115200,N,8,1 90W 1000 LNK ACT 60W 100 LNK ACT 30W 5 6 Figure 6-2: IGS-5225-4P2S Reset Button 1000 LNK ACT 10/100 LNK ACT 4 4 3 3 PoE-in-Use 2 2 Reset 1 1 bt af/at Reset IGS-5225-4UP1T2S Figure 6-3: IGS-5225-4UP1T2S Reset Button 18 9 Reset 11 11 12 13 13 14 Reset 10 1G LNK/ACT 10/100 LNK/ACT 12 14 1G/2.5G LNK/ACT 100 LNK/ACT IGS-5225-8P2T4S Figure 6-4: IGS-5225-8P4S/IGS-5225-8P4S-12V/IGS-5225-8P2T2S/ IGS-5225-8P2T4S Reset Button 19 7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQs: http://www.planet.com.tw/en/support/faq Switch support team mail address: support@planet.com.tw IGS-5225-4T2S/IGS-5225-4P2S/ IGS-5225-8P2T4S/IGS-5225-8P4S/ IGS-5225-8P4S-12V/IGS-5225-8P2T2S/IGS-5225-4UP1T2S User's Manual: https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=IGS-5225&view=3#list (Please select your switch model name from the Product Model dropdown menu) Copyright © PLANET Technology Corp. 2022. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. 20