User Manual for SYNCO models including: P2T, Dual Microphone, P2T Dual Microphone, Microphone
Synco P2T Miniature 2-Person Digital Wireless Microphone P2T-BL
【下書き】iPhone 13 Proではなく、Galaxy S22 Ultraを使っている理由【SYNCO P2T】 | GEEK – KAZU
Microphone P2T User Manual Thank you for choosing SYNCO product. Please read this manual carefully before use and follow all instructions mentioned herein. Caring For Your SYNCO Product Please keep the product in a dry, clean, dust-free environment. Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage. Use only a soft and dry cloth for cleaning the product. Malfunction may be caused by dropping, impact of external force. Do not attempt to disassemble the product. Doing so voids warranty. Please have the product checked or repaired by authorized technicians if any malfunctions happened. Failure to follow all the instructions may result in mechanics damage. Warranty does not apply to human errors. Package List Charging Cable x1 TX Transmitter x2 RX Receiver (Type-C Connector) x1 Wireless Charging Case x1 Type-C to 3.5mm Adapter x1 Product Instruction TX Transmitter RX Receiver Wireless Charging Case TX Transmitter Power Working Indicators Built-in Mic Contacts Pocket Clip RX Receiver Vocal Effects/ Mono/Stereo Type-C Port Working Indicators Connector Contacts Wireless Charging Case Pairing/ Power Prompt Type-C Port Working Indicators Contacts Indicator -- Transmitter (Double press the Power button to turn off light effect) Flash concurrently System unpaired Working Indicators(White Light) Illuminate sequentially(light effect on) Single light keeps on (light effect off) System paired, normal working Single light flashes Working Single light keeps on (in the case) Indicators(Red Light) Low battery Charging, and then turns off when fully charge Indicator -- Receiver Flash concurrently System unpaired Illuminate sequentially System paired Working Indicators (White Light) Single light keeps on & Illuminate sequentially Single light flashes twice & Illuminate sequentially Single light keeps on & Illuminate sequentially two-way Mono mode-Original sound Mono mode-Vocal effects on Stereo mode (Only original is supported) Indicator -- Wireless Charging Case Working Illuminate sequentially Indicators(White Light) Pairing Operations 1. Usage Tap on the right side of charging case to pop out the drawer Take the TX and RX out TX should boot automatically as it leaved the case, and switch itself off automatically when returning to the case. (Forcible switch: Long press the Power button on TX for 3 seconds) RX should boot automatically as it is plugged into smartphone 2. Pairing Place the TX and RX in the case with their contacts are connected with the case's Long press the Pairing button on the case for 3 seconds with the drawer open The indicators on the TX and RX should light up and illuminate sequentially when pairing is successful Note: The transmitter will automatically switch off if it is unpaired or disconnected for 5 minutes. Long press for 3 seconds 3. Charging Charge the TX: Place the TX in the case with contacts connected with the case's. Charge the case: Connect the case with power supply via the charging cable. 4. Check the power TX: Short press the Power button, the indicators will light up according to remain power for 5 seconds Charging Case: Short press the Power Prompt button, the indicators will light up according to remain power for 5 seconds 5. Use vocal effects Short press the Vocal Effects button on the receiver to switch sound effects: Original >> Studio FX >> KTV FX >> Voice Amplification >> EDM (Electronic Dance Music) >> Baby FX >> Male to Female >> Female to Male >> Monster FX. Default effect: Original. Note: The vocal effect will apply to both transmitters. In Stereo mode, only original is supported. Other vocal effects are unavailable. 6. Mono/ Stereo Long press the Mono/Stereo button on the RX once Long press the Mono/Stereo button on the RX once Mono-Original Stereo Mono-Original Mono-Other vocal effects Long press the Mono/Stereo button on the RX once 7. Charging phone device Plug your phone charging cable into the Type-C Port on the receiver. 8. In-Ear monitoring Plug the included Type-C to 3.5mm Adapter into the Type-C Port on the receiver. Then plug in your headphones to realtime monitor mic recording and device's backgrounding. Note: The included Type-C to 3.5mm Adapter is exclusive, not available for other devices. Specifications TX Transmitter Wireless Transmission RF Frequency Band Frequency Response Working Distance Sampling Rate Bit Depth Sensitivity SNR RF Output Power Battery Type Battery Charging Time Battery Life Dimensions Material Weight RX Receiver Wireless Transmission RF Frequency Band Digital 2.4GHz 2400-2483.5MHz 20Hz-20KHz 492ft/150m(LOS area); 164ft/50m(NLOS area) 48KHz 16Bit -26dB >75dB 10dB Built-in Lithium Battery, 120mAh 1.5H 5H 49x19x19 (mm) ABS 10g Digital 2.4GHz 2400-2483.5MHz Working Distance Sampling Rate Bit Depth Antenna Monitoring Connector Power Input Dimensions Material Weight Wireless Charging Case Battery Type Battery Charging Time Charging Port Power Requirements Dimensions Weight 492ft/150m(LOS area); 164ft/50m(NLOS area) 48KHz 16Bit Built-in 3.5mm In-Ear Monitoring Type-C Output Type-C 49x30x9 (mm) ABS 5g Built-in Lithium Battery, 700mAh 2H Type-C Port 5V 2A 70x68x38mm 87.5g Warranty Warranty Period Thank you for purchasing SYNCO products. 1. Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product. 2. Original SYNCO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user. Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee). Warranty Exclusions and Limitations Faults resulted from inappropriate use of a product without following its operation specification Artificial damage, e.g. crash, squeeze, scratch, or soaking Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g. replacement of element or circuit, label alteration The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off All consumable accessory attached to a product, like cable, wind muff, battery Faults as a result of force majeure, such as fire, flood, lightning, etc. Warranty Claim Procedure If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO's customer service through email at support@syncoaudio.com. Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided. If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged. Guangzhou Zhiying Technology Co., Ltd Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000 support@syncoaudio.com www.syncoaudio.com https://www.facebook.com/syncomicrophones WARRANTY CERTIFICATE Please register your warranty. Meanwhile, you are welcomed to contact us via Email support@syncoaudio.com Customer Name: USER INFORMATION Phone Number: Email: Address: Sales Date: SALES INFORMATION Model: Product Code: Dealer: Service Date: REPAIR RECORD Technician: Issue: RESULT Solved Unsolved Returned(Replaced)Adobe PDF Library 15.0 Adobe InDesign CC 14.0 (Windows)