152Y Remote Control System User Manual
I. ELECTRONICS OVERVIEW
This section provides an overview of the electronic components of the 152Y system.
The system includes:
- Remote controller: Model 152Y. Features buttons for TV, M, ZG, memory positions, up/down adjustments, OFF, SW, LED, and FLAT.
- Control box: Model 152Y, designed to work with the remote controller. It has ports labeled "POWER LINE", "LED", "SYNCHRO", "WORK STATUS CONNECT", "LAMP", and "BUTTON".
- Power supply: Connects the control box to the mains power.
- Motors: Two motors are shown connected to the control box, typically used for adjustable beds.
The diagram illustrates the connection between the power supply, the control box, and the motors. The remote controller is shown separately.
II. PAIRING THE WIRELESS REMOTE
Follow these steps to pair the wireless remote controller with the control box.
STEP 1: Install Batteries
Push the bottom of the remote to release the battery cartridge. Install three AAA batteries into the remote's battery compartment. Push firmly to close the cartridge.
STEP 2: Initiate Pairing on Control Box
Plug the control box into a power source. Press the Pairing Button/Program Button on the control box for approximately 1 second. Ensure the Pairing Lamp - White (Third) is flashing.
STEP 3: Complete Pairing with Remote
On the remote controller:
- Press the "SW" button until the backlight LED starts flashing. Release the "SW" button.
- Immediately press the "HEAD UP" button [Up Arrow]. Do not release it until the backlight LED lights up continuously. The remote is now pairing. Release the button.
- Next, press the "BACK UP" button [Down Arrow]. Do not release it until the backlight LED lights up continuously. Release the button.
Pairing Confirmation: Pairing is completed when the Pairing Button/Program Button on the control box and the backlight LED on the remote stop flashing, and the control box emits a "DI" sound from the buzzer.
If the remote functions are not operational after pairing, repeat the pairing process.
III. FUNCTIONAL OPERATING FOR WIRELESS REMOTE
This section details the functions controllable via the wireless remote.
| MARK | STEP 1 | STEP 2 | FUNCTIONAL | DESCRIPTIONS |
|---|---|---|---|---|
|
[Up Arrow] [Down Arrow] TV ZG M + - OFF SW LED FLAT |
Press "SW" in 3s until the backlight LED flashing and then press the "BUTTON" in STEP 2 | TV | MEMORY POSITON |
The backlight LEDs all OFF before operating. • Press (TV, ZG, M) until the backlight LED is lighting and the memory position is completed. • When the backlight LED is lighting and press again, clear the corresponding memory position. • TV & ZG have the memory position, M has no memory position. |
| ZG | ||||
| M | ||||
| BACK UP | PAIRING | Pairing the remote and control box. | ||
| Press LEG UP 3 seconds | CONTROL SWITCHING | Control Switching is the backlight LED of "SW" is OFF. | ||
| Press SW 3 seconds | Control Switching is the backlight LED of "SW" is ON. | |||
| Press BOTTOM LED 3 seconds | Control Switching is the backlight LED of "SW" is FLASHING. |
IV. FUNCTIONAL OPERATING FOR WIRELESS REMOTE
This section covers power specifications and motor control.
Power Supply Specifications:
- Input: 100-240V~, 50/60Hz
- Output: 29.0V = 3.0A
Motor Control:
By pairing the remote control with the control box, the motor(s) can be controlled to move up and down.
Product Interface Description
The interfaces on the control box are described below. Note that the interfaces highlighted in red in the diagram are intended for engineering testing purposes only and are not accessible to consumers.
The control box features ports for power input, LED indicators, synchronization, work status, lamp, and buttons. Specific connectors are shown, with a note that certain interfaces are for engineering use only.
The control box has labels for: POWER LINE, LED, SYNCHRO, WORK STATUS CONNECT, LAMP, BUTTON. It also features a [Foot Icon] and a [Person Icon] near the WORK STATUS CONNECT and LAMP labels respectively. Two specific connectors are highlighted as being for engineering testing only.
FCC/ISEDC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
