Polaris 2024+ RZR Single Light Reverse Light Kit Installation Manual

Product Overview

This manual provides instructions for installing the 2024+ Polaris RZR Single Light Reverse Light Kit. It includes a list of included components, required tools, and step-by-step installation procedures. Please read the entire manual before beginning the installation process.

Disclaimer: Sam's Backup Lights is not responsible for any damage due to improper installation.

Included Components

Required Tools

Installation Steps

Step 1: Remove Seats & Shifter

Textual description of images:

• Image 1: Close-up of a vehicle seat, highlighting a red release lever at the rear.
• Image 2: Interior view of a vehicle cabin, showing the area around the shifter and center console.
• Image 3: Close-up of the vehicle's shifter mechanism.
• Image 4: View of the vehicle floor area near the pedals.

1. Remove seats by pulling up on the red release at the rear of the seat.
2. Remove the shifter top by removing the T-25 screw and removing the cover.
3. Remove the T-25 screw uncovered by the cover. Pull up to remove the shifter.

Step 2: Remove Center Console

Textual description of images:

• Image 1 & 2: Views of the vehicle's center console, showing screws and push-rivets that need to be removed.
• Image 3 & 4: Interior views of the vehicle after the center console has been partially removed, revealing wiring and components underneath.

1. Remove the front center console by removing 7 T-40 screws and the three push-rivets. Remove the center console.
2. To remove the rear cup holders, unscrew the 4 T-40 screws and remove the three push rivets. (Watch out for the wires for the 12V Plug). Note: this is only for a 4-seater.
3. Remove the rear cover by turning the four push locks and pulling on the cover.

Step 3: Secure & Plug in Controller

Textual description of images:

• Image 1: Close-up of a diagnostic connector being plugged into a corresponding connector on the new wiring harness.
• Image 2: View of the vehicle's interior showing the controller, relay, and fuse holder secured with zip ties.
• Image 3: Close-up of wiring and connectors near the vehicle's bus bar, indicating where power and ground are connected.
• Image 4: Close-up of the control box connector being plugged into its mating connector.

1. Remove the diagnostic connector cover and plug in the connector included with the reverse light wiring harness.
2. Secure controller, relay, and fuse using zip-ties.
3. Remove the cover for the bus bar and plug in the power and ground.
4. Plug in the control box.

Step 4: Mounting the Light

Textual description of the image:

• A rear view of a Polaris RZR vehicle, showing the designated mounting location for the reverse light. The "POLARIS" logo is prominently displayed above the mounting area. The reverse light is shown attached to its bracket.

1. Remove rear plastics if needed; drill hole in center of mounting spot as shown in figure below.
2. Mount light to provided bracket. (Be sure to slide bolt through bracket before attaching light to it).
3. Secure light with provided hardware.

Step 5: Route Power to Light

Textual description of images:

• Image 1 & 2: Interior views of the vehicle's cabin and undercarriage, illustrating the routing of the wiring harness along existing OEM harnesses.

1. Route reverse light harness down from the control box position into the cab, and, following the OEM harness, run straight through cab.
2. Route wiring harness behind cab, along the OEM harness to rear of vehicle.
3. Plug wiring harness connector into light connector.
4. Zip tie as needed.
5. Note: If installing kit on 2-seater, coil excess wire either by control box or directly behind seat.

Step 6: Reinstall Plastics

Reinstall all removed plastics and components in reverse order of removal.

Operation of Reverse Lights

Textual description of the logo:

• A circular logo with "SAM'S BACKUP LIGHTS" text.

Our controllers have been programmed with a manual override feature. Back-up lights may be turned on without the vehicle in reverse.

Fully Automatic when shifted to Reverse Gear

1. No programming required.

Manual Override Function

1. Shift the vehicle into Neutral.
2. Press and hold the brake pedal for up to 2 seconds. The reverse light will automatically turn on and stay on.

To turn the light off repeat this procedure.

Note: If the ignition is turned off while the vehicle is in reverse, or the manual override function is enabled, the lights will remain ON until the ECU enters sleep mode (approximately 30 secs to 2 minutes depending on vehicle and ECU type).