ELIMINATOR LIGHTING Introduces Stryker LED Powered Beam Moving Head Instructions

Instructions for ELIMINATOR LIGHTING models including: Introduces Stryker LED Powered Beam Moving Head, Introduces Stryker, LED Powered Beam Moving Head, Powered Beam Moving Head, Beam Moving Head, Moving Head

STRYKER BEAM

Download

Eliminator Lighting Stryker Beam

File Info : application/pdf, 29 Pages, 2.61MB

JavaScript is disabled. Open the PDF or Download.

Eliminator Stryker Beam - User Manual 02-14-2024

STRYKER BEAM
User Instructions

©2024 Eliminator Lighting all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. Eliminator Lighting logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-Eliminator brands and product names are trademarks or registered trademarks of their respective companies.
Eliminator Lighting and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.

DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of this document may be available online. Please check www.adj.com for the latest revision/update of this manual before beginning installation and/or programming.

Date
02/27/2023 05/22/2023 08/23/2023 02/14/2024

Document Version 1.0 1.1 1.2 1.3

Software Version
1.0 N/C N/C N/C

DMX Channels
13/19 ch. No Change No Change No Change

Notes
Initial Release Updated FCC Statement Updated Specifications Updated Approvals

Europe Energy Saving Notice Energy Saving Matters (EuP 2009/125/EC) Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!
2

TABLE OF CONTENTS

Introduction

Limited Warranty (USA Only) | Warranty Registration 5

Features

Safety Precautions

Overview

Installation

Color Wheel | Gobos

Control Panel

System Menu

DMX Set Up

DMX Traits

Primary-Secondary Set Up

Maintenance Guidelines

Dimensional Drawings

Specifications

INTRODUCTION
Unpacking: Thank you for purchasing the Stryker Beam. Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to have been damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit have arrived intact. In the event that damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The Stryker Beam is a DMX-capable, LED-powered moving head fixture. It features multiple selectable DMX channel modes, pan and tilt control, 13 colors, and 11 static gobos, among other effects.
Customer Support: Contact ADJ Service for any product related service and support needs. Also visit forums.adj.com with questions, comments or suggestions. Parts: To purchase parts online visit: http://parts.adj.com (US) http://www.adjparts.eu (EU) ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST Voice: 800-322-6337 | Fax: 323-582-2941 | support@adj.com ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | support@adj.eu
ADJ PRODUCTS LLC USA 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com ADJ SUPPLY Europe B.V Junostraat 2 6468 EW Kerkrade, The Netherlands +31 (0)45 546 85 00 | Fax +31 45 546 85 99 www.americandj.eu | info@americandj.eu ADJ PRODUCTS GROUP Mexico AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000 +52 (728) 282-7070
CAUTION! This device is intended for indoor use only! Do not expose to rain or moisture!
CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as doing so will void your manufacturer's warranty. In the unlikely event your unit may require service, please contact ADJ Products, LLC. Do not discard the shipping cartoon in the trash. Please recycle when ever possible.
4

LIMITED WARRANTY (USA ONLY)
1 Year Limited Warranty: The Eliminator Lighting warranty is valid for 1 year from the date of purchase. Our 1 year limited warranty covers manufacturing defects only. The serial number of your device and the place of purchase with dated valid receipt must be submitted at time of service. The Eliminator Lighting warranty does not cover items or parts prone to wear and tear: lamps, fuses, brushes and belts. Eliminator Lighting warranty is only valid within the United States. To register your Eliminator Lighting product online, please click here to the ADJ Warranty Registration Page: https://www.adj.com/portal/user/register/
WARRANTY REGISTRATION
Please fill out the enclosed warranty card to validate your purchase. All returned service items, whether under warranty or not, must be freight pre-paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain an R.A. number by contacting our customer support team. All packages returned to the service department not displaying an R.A. number on the outside of the package will be returned to the shipper.
5

F E AT U R E S
· 1 x 100W LED · Multiple selectable DMX channel modes · Pan and tilt adjustment · 13 colors · 11 static gobos · Effect wheel with bi-directional rotating prisms · Single 6-color chip · Adjustable dimming and strobing · LCD display INCLUDED ITEMS · Power Cable (x1) · Omega Bracket (x1)
6

SAFETY PRECAUTIONS
PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER'S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER'S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
INDOOR USE ONLY! DO NOT EXPOSE TO RAIN OR MOISTURE!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK - MAY INDUCE BLINDNESS! SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
· Maximum ambient operating temperature is 113° F (45° C)! · DO NOT TOUCH the fixture housing during operation. Disconnect the power and allow approximately
15 minutes for the fixture to cool down before servicing. · DO NOT shake the fixture, and avoid brute force when installing and/or operating the fixture. · DO NOT operate the fixture if the power cord has become frayed, crimped and/or damaged. If the
power cord is damaged, replace immediately with a new one of the same power rating. · DO NOT attempt to remove or break off the ground prong from the electrical cord. This prong is used
to reduce the risk of electrical shock and fire in the event of an internal short. · DO NOT attempt to operate this unit if it has been damaged in any way. · DO NOT spill water or other liquids into or on to your unit. · Disconnect from main power before making any type of connection. · DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked.
Allow approx. 20" (50cm) between fixture and other devices or a wall for proper cooling. · Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 20" (50cm)
between this device and a wall. · DO NOT remove the cover for any reason. · When installing fixture in a suspended enviroment, always use mounting hardware that is no less than
M10 x 25mm, and always install fixture with an appropriately rated safety cable. · Never plug this unit in to a dimmer pack. · During long periods of non-use, disconnect the unit's main power. · Always mount this unit in safe and stable matter. · Power-supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to the point where they exit from the unit. · Cleaning - The fixture should be cleaned only as recommended by the manufacturer. · Heat - The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat. · The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug have been damaged. B. Objects have fallen onto, or liquid has been spilled into, the fixture. C. The fixture does not appear to operate normally or exhibits a marked change in performance. D. The fixture has fallen and/or has been subjected to extreme handling.
7

OVERVIEW
DMX LED Run LED Display Screen

ESC Button
Up Button
Down Button
Set Button

3pin DMX In

3pin

5pin 5pin

Power

DMX Out DMX In DMX Out

Fuse
Power Out

I N S TA L L AT I O N
DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO! Fixture MUST be installed following all local, national, and country commercial electrical and construction codes and regulations. When installing the unit, the trussing or area of installation must be able to hold at least 10 times the weight of the unit and any attached accessories without any deformation. The unit must be secured with a secondary safety attachment, e.g. an appropriately-rated safety cable. Before rigging/mounting a single fixture to any metal truss/structure or placing the fixture(s) on any surface, a professional equipment installer MUST be consulted to determine if the metal truss/structure or surface is properly certified to safely hold the combined weight of the fixture(s), clamps, cables, and accessories. Maximum ambient operating temperature is 113°F (45°C). Fixture(s) should be installed away from walking paths, seating areas, or areas where unauthorized personnel might reach the fixture by hand. NEVER stand directly below the fixture(s) when rigging, removing, or servicing. Overhead fixture installation must always be secured with a secondary safety attachment, such as an appropriately rated safety cable that can hold at least 10 times the weight of the fixture. Overhead mounting requires extensive experience, including calculating working load limits, knowledge of installation material being used, and perodic safety inspection of all installation material as well as the unit itself. If you lack these qualifications, do not attempt the installation yourself. The installation should be checked by a skilled person once a year.
9

I N S TA L L AT I O N
CLAMP MOUNTING This fixture features attachment points for two mounting clamps on the bottom surface of the unit. Additionally, the unit also features a safety cable loop located just below the display screen (see the illustration below). When mounting the fixture to a truss or any other suspended or overhead installation, be sure to secure TWO appropriately rated clamps (not included) to the bracket installation points, and attach a separate SAFETY CABLE of the appropriate weight rating to the provided safety cable loop.

MOUNTING CLAMP
INSTALLATION POINT
SAFETY CABLE LOOP

MOUNTING CLAMP
INSTALLATION POINT
SAFETY CABLE:
ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS
FIXTURE IN A SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE WILL NOT FALL IF THE CLAMP FAILS.

NOTICE: The maximum ambient operational temperature for this lighting fixture is 113° F (45° C). Do not place this lighting fixture in an environment where the temperatures exceed this value. This will allow the fixture to run at its best and help prolong the fixture life.
10

I N S TA L L AT I O N
RIGGING ORIENTATIONS Overhead rigging requires extensive experience, including calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the fixture, among other skills. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. The fixture is fully operational in the following positions: hanging from a horizontal truss, suspended sideways from a vertical truss, or standing upright on a flat, level surface. See the illustration below for reference.
11

I N S TA L L AT I O N
POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS External sources of light beams from direct sunlight, lighting and moving head fixtures, and lasers, which are focused directly towards the exterior housing and/or penetrate the front lens opening of Eliminator lighting fixtures, can cause severe internal damage including burning of optics, dichroic color filters, glass and metal gobos, prisms, animation wheels, frost filters, iris, shutters, motors, belts, wiring, discharge lamps, and LEDs. This issue is not specific only to Eliminator lighting fixtures, but rather it is a common issue with lighting fixtures from all manufacturers. Although there is no true way to fully prevent this issue from happening, the guidelines below can reduce the risk of potential damage. Contact ADJ Service for more details. DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT SUNLIGHT, OTHER LIGHTING OR MOVING HEAD FIXTURES, AND LASERS DURING UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.
12

COLOR WHEEL
Red Orange Blue Green

Open

Purple
Orange Yellow

Light Yellow

Silver

Yellow Carmine

Royal Blue

Reseda Pink

GOBOS

1 2

Open

11 10

CONTROL PANEL
The Stryker Beam features a display screen with a 6-button control pad, which can be used to easily adjust any device settings. Pressing the UP and DOWN buttons to scroll through options on the screen. Press SET to select the option currently highlighted on the screen, and enter into the Sub-Menu to adjust that setting, if applicable. Press ESC to exit without making changes. The panel also includes two LEDs, which indicate whether the unit is in DMX mode ("DMX" LED is illuminated) or Standalone mode ("RUN" LED is illuminated).
14

SYSTEM MENU

ADDR

001 - 512 Prev Next

Chan

DMX Ctrl Auto Run Sound Ctrl

MODE

Scene Mode

M/S Choose

Screen Saver

DISP

Screen Rot

DMX Indicate

SCENE

Screen Light Scene Select Scene Time Control Mode 01. Pan 02. Pan Fine 03. Tilt 04. Tilt Fine 05. Color 06. Gobo 07. Strobe 08. Dimmer

13 CH 19 CH
Auto 01 - 10 Primary Auto Secondary Mode 1 Mode 2 Mode 3 Mode 4 Off Reverse
Forward
Mode 1
Mode 2
Mode 3
001 - 010 1 - 10 0s - 25.5s On / Off 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255
CONTINUED ON NEXT PAGE
15

Select DMX address
Select DMX channel mode DMX control mode Auto run mode Sound active mode
Scene mode
Black screen DMX address Model name Model name Screen saver off Invert display orientation Standard display orientation Connected: LED On Not Connected: LED Off Connected: LED Off Not Connected: Led On Connected: LED flash Not Connected: LED Off Screen display brightness

SYSTEM MENU

SCENE (cont'd)

09. Focus 10. Prism 1 11. Prism 1 R 12. Prism 2 13. Prism 2 R 14. Frost 15. 7 Color 16. Function 17. Mode 18. PT Speed 19. Reset Pan Invert Tilt Invert

P/T Rectify

ADVA

Pan Offset Tilt Offset Data Hold Scene Time

Reset

000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 On / Off On / Off
On / Off
004 - 150 004 - 048
On / Off
001 - 255
Yes / No

Factory Setting Yes / No

Returns pan/tilt to previous setting in the event of accidental strike
Holds last DMX setting received if signal is lost
Power reset: powers fixture off then powers it back on Return unit to factory default settings

CONTINUED ON NEXT PAGE

SYSTEM MENU

STAT

Stepper Info

Error Logging

STAT (cont'd)

Fixture Status
Version Light Time Total Time Serial Number

Pan Tilt Pan OP Tilt OP 01 Pan 02 Tilt 03 Gobo1 04 Color1 05 Prism1 06 Prism2 07 Prism Rot1 08 Prism Rot2 09 Focus1 10 Frost 11 MT1
Communication Error Cnt Light Temp Panel Temp Sensor1 Temp Sensor2 Temp x.x.x
xxx:xx
xxx:xx

xxx xxx xx xx xxx xxx xxx xxx xxx xxx xxx xxx xxx xxx xxx
xxx% x xx F / xx C xx F / xx C xx F / xx C xx F / xx C

Rainbow mirror motor Display error log
Time since unit was last powered on Total lifetime run time

DMX SET UP
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA "IN" and DATA "OUT" XLR terminals located on all DMX fixtures (most controllers only have a DATA "OUT" terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

FIXTURE 1

FIXTURE 2

DMX CONTROLLER

DMX DMX

OUT

FIXTURE 3

DMX DMX IN OUT
FIXTURE 4

DMX DMX IN OUT

ADDITIONAL FIXTURES

Note: The diagram above depicts DMX linking via the 3-pin DMX ports, but the units can also be linked via the 5-pin DMX ports. However, all linkages must be made using the same set of ports: all 3-pin or all 5-pin.
18

DMX SET UP
Data Cable (DMX Cable) Requirements (For DMX Operation): This unit can be controlled via DMX-512 protocol. The DMX address is set on the rear panel of the unit. Your unit and your DMX controller require a standard 3-pin or 5-pin XLR connector for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables should be made with a male XLR connector at one end and a female XLR connector at the other. Also remember that DMX cable must be daisy chained and cannot be split. Notice: Be sure to follow the illustration below when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable's shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR's outer casing. Grounding the shield could cause a short circuit and erratic behavior.
Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will reduce the risk of erratic behavior.
19

DMX SET UP
DMX ADDRESSING. All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to "listen" to the digital control signal sent out from the DMX controller. The assignment of this starting DMX address is achieved by setting the correct DMX address on the digital control display on the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different addresses for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to react in the same way. In other words, changing the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to "listen" to the channel number you have set, based on the quantity of DMX channels of each fixture. That means changing the settings of one channel will only affect the selected fixture.
For example, when operating this unit in 13-channel mode, you should set the starting DMX address of the first unit to 1, the second unit to 14 (1 + 13), the third unit to 27 (1 + 13 + 13), and so on. See the chart below for more details.

CHANNEL MODE UNIT 1 ADDRESS UNIT 2 ADDRESS UNIT 3 ADDRESS UNIT 4 ADDRESS

13 Ch

19 Ch

DMX TRAITS

CHANNEL

13Ch 19Ch

DMX VALUES 000 - 255 000 - 255 000 - 255 000 - 255
000 - 004 005 - 009 010 - 014 015 - 019 020 - 024 025 - 029 030 - 034 035 - 039 040 - 044 045 - 049 050 - 054 055 - 059 060 - 064 065 - 069 070 - 074 075 - 079 080 - 084 085 - 089 090 - 094 095 - 099 100 - 104 105 - 109 110 - 114 115 - 119 120 - 124 125 - 129 130 - 134 135 - 139 140 - 149 150 - 199 200 - 205 206 - 255

FUNCTION
Pan, 0 - 540 Pan Fine Tilt, 0 - 225 Tilt Fine Color White White + Red Red Red + Orange Orange Orange + Blue Blue Blue + Green Green Green + Yellow Yellow Yellow + Carmine Carmine Carmine + Royal Blue Royal Blue Royal Blue + Pink Pink Pink + Reseda Reseda Reseda + Silver Silver Silver + Light Yellow Light Yellow Light Yellow + Orange Yellow Orange Yellow Orange Yellow + Purple Purple Purple + White White Clockwise Rotation (fast to slow) Stop Counter Clockwise Rotation (slow to fast)

CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL 13Ch 19Ch

DMX VALUES
000 - 009 010 - 019 020 - 029 030 - 039 040 - 049 050 - 059 060 - 069 070 - 079 080 - 089 090 - 099 100 - 109 110 - 119 120 - 127 128 - 135 136 - 143 144 - 151 152 - 159 160 - 167 168 - 175 176 - 183 184 - 191 192 - 199 200 - 207 208 - 230 231 - 232 233 - 255
000 - 003 004 - 127 128 - 191 192 - 251 252 - 255 000 - 255 000 - 255

FUNCTION
Gobo Open Gobo1 Gobo2 Gobo3 Gobo4 Gobo5 Gobo6 Gobo7 Gobo8 Gobo9 Gobo10 Gobo11 Gobo1 Shake, slow to fast Gobo2 Shake, slow to fast Gobo3 Shake, slow to fast Gobo4 Shake, slow to fast Gobo5 Shake, slow to fast Gobo6 Shake, slow to fast Gobo7 Shake, slow to fast Gobo8 Shake, slow to fast Gobo9 Shake, slow to fast Gobo10 Shake, slow to fast Gobo11 Shake, slow to fast Clockwise Rotation, fast to slow Stop Counter Clockwise Rotation, slow to fast Shutter Off Strobe, slow to fast Pulse Strobe, slow to fast Random Strobe, slow to fast Open Dimmer, 0% to 100% Focus, far to near

CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL 13Ch 19Ch
10
11
12
13
8 14 9 15 10 16 11 17 12 18 13 19

DMX VALUES
000 - 127 128 - 255
000 - 063 064 - 126 127 - 128 129 - 191 192 - 255
000 - 127 128 - 255
000 - 063 064 - 126 127 - 128 129 - 191 192 - 255
000 - 127 128 - 255
000 001 - 255
000 - 127 128 - 255
000 - 127 128 - 255 000 - 255
000 - 021 022 - 025 026 - 076 077 - 128 129 - 255

FUNCTION
Prism 1 Off On Prism 1 Rotation
Prism Index, 0° - 400° Clockwise Rotation, fast to slow Stop Counter Clockwise Rotation, slow to fast Bi-directional Rotation, slow to fast Prism 2 Off On Prism 2 Rotation
Prism Index, 0° - 400° Clockwise Rotation, fast to slow Stop Counter Clockwise Rotation, slow to fast Bi-directional Rotation, slow to fast Frost Off On 7 Color Off On Effect Auto Off Auto Run On Pan/Tilt Auto Off Auto Run On Pan/Tilt Speed, fast to slow Reset Off No function Reset Effect (hold 3s) Reset Pan/Tilt Motor (hold 3s) Reset All (hold 3s)

PRIMARY-SECONDARY SET UP
This function allows you to link units together to run in a Primary-Secondary set-up, in which one unit will act as the controlling unit and the others will react to the controlling unit's built-in programs. Any unit can be configured to act as a Primary or as a Secondary, but only one unit in a given system can be programmed to act as the Primary. Primary-Secondary Connections and Settings: 1. Daisy chain your units via the XLR connectors on the rear panels of each unit. Use standard XLR
data cables to link your units together. Remember that the male XLR connector is the input and the female XLR connector is the ouput. The first unit in the chain (primary) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only. 2. Use the display screen and control panel to navigate to the "Primary / Secondary" setting in the main menu. Select this setting using the ENTER button, and use the arrows to toggle between "Primary", "Secondary1", and "Secondary2". Press ENTER to confirm your selection. 3. Repeat Step 2 for each unit in the system. Make sure that only one unit is designated as the Primary, while all other units are designated as Secondaries. 4. The secondary units will act in conjunction with the primary unit. Note that secondary units set to the "Secondary1" setting will follow the motions of the primary, while those set to the "Secondary2" setting will move in contrast to the primary.
24

MAINTENANCE GUIDELINES
DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
CLEANING Frequent cleaning is recommended to ensure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the fixture operates: damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on the fixture's optics. Clean the external lens surface regularly with a soft cloth to avoid dirt/debris accumulation. NEVER use alcohol, solvents, or ammonia-based cleaners. MAINTENANCE Regular inspections are recommended to ensure proper function and extended life. There are no user serviceable parts inside this fixture. Please refer all other service issues to an authorized ADJ or Eliminator service technician. Should you need any spare parts, please order genuine parts from your local ADJ/Eliminator dealer. Please refer to the following points during routine inspections: A. A detailed electrical check by an approved electrical engineer every three months, to make sure
the circuit contacts are in good condition and prevent overheating. B. Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out
during normal operation, resulting in damage or injury as larger parts could fall. C. Check for any deformations on the housing, color lenses, rigging hardware, and rigging points
(ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s). D. Electric power supply cables must not show any damage, material fatigue, or sediments. NEVER remove the ground prong from the power cable. SOFTWARE UPDATES Please contact ADJ service for assistance with updating your device's software.
25

DIMENSIONAL DRAWINGS
11.5in. [292.1mm]

11.0in. [279.4mm]

16.0in. [405.3mm] 18.3in. [464.0mm]

7.9in. [200.0mm]

11.9in. [302.3mm]

Drawings not shown to scale.

S P E C I F I C AT I O N S
LIGHT SOURCE: · 100W LED Engine · 6-Degree Beam Angle
FEATURES: · Full color function display with 4 buttons · Fast, precise, pan & tilt movements · Primary / Secondary stand-alone mode · Motorized Focus · Frost Filter (50-Degree Wash Effect)
COLOR WHEEL: · 13 colors + open · Separate 6-Color flag for multi-color effects
GOBO WHEEL: · Metal wheel with 11 GOBOS + open (2 are beam reducers) · GOBO Shake Effect
PRISM WHEEL: · 8-facet rotating circular prism · 16-facet rotating circular prism · Prism layering
CONTROL: · 2 DMX channel modes: 6 & 19 channels · Protocols: DMX-512, RDM, Auto and Primary/Secondary control modes · Electronic Dimmer: 0- 100 % · Variable Strobe: 0-20HZ · With Wired Digital Communication Network
CONNECTIONS: · DMX Data In/Out: 3-pin & 5-pin connections · Power In: Blue Locking indoor power connection · Power Out: White Locking indoor power connection
PAN/TILT: · Pan/Tilt: 540-degrees / 270-degrees · 16-bit Fine Pan · 16-bit Fine Tilt
ELECTRICAL: · Multi-voltage operation: AC 100-24V, 50/60Hz · Maximum Power Consumption: 150W · Power daisy chain: 2 units @120V, 3 units @230V

DIMENSIONS & WEIGHT: · Dimensions (LxWxH): 11.5" x 11.9" x 18.3" / 292.1x302.3x464.0mm · Weight: 29 lbs. / 12.8 kg.
Road Cases (Sold Separately): · Two (2) Stryker Beam fit inside the ADJ DRC MH road case · Four (4) Stryker Beam fit inside the ADJ QRC HM road case
WHAT'S INCLUDED: · Locking power cord · Omega bracket
APPROVALS: · cETL Approved (Control # 5027824) · FCC Compliant · CE Compliant · IP20

Specifications subject to change without notice.
27

FCC INFORMATION
FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device uses and can radiate radio frequency energy and, if not installed and used in accordance with the included instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be deter- mined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following methods: · Reorient or relocate the device. · Increase the separation between the device and the receiver. · Connect the device to an electrical outlet on a circuit different from which the radio
receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Energy Saving Matters (EuP 2009/125/EC) Saving electric energy is a key to help protecting the environment. Please turn off all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!
28

References

Adobe PDF Library 17.0 Adobe InDesign 19.2 (Macintosh)