Instruction Manual for Locks models including: D2, 2A9XT-D2, 2A9XTD2, D2 Basic Version Lock, Basic Version Lock, Lock
FBA Seller Inc. D2 D2 American Deadbolt 2A9XT-D2 2A9XTD2 d2
D2 D2 American Deadbolt by FBA Seller
File Info : application/pdf, 4 Pages, 1.32MB
DocumentDocumentOPERATING INSTRUCTIONS FOR D2 LOCKING BASIC VERSION St3.5 * 20 + countersunk head tapping screws (2) M6 * 50 + countersunk head screws (2) Cross countersunk head M4*8+2 Buckle box Interior Assembly Mounting Plate Entry Key Touch Keypad Assembly Deadbolt Strike plate Deadbolt Latch (2 ea.) St3.5 * 20 + countersunk head tapping screws (2) M6 * 50 + countersunk head screws (2) Cross countersunk head MODE: D2 SMALL SCREEN + FINGERPRINT HEAD 1 2 Install the latch and strike 1 . Insert the latch bolt into the door. St3.5 * 20s cross countersunk head tapping screw Make sure t he T-shaped hole is in the bottom position. up YES up NO No adjustment is required. Proceed to next step. Twist the latch and adjust the bolt length. (Make sure the latch bolt is retracted). Install the interior assembly 1. Take off the mounting plate. Mounting plate 2. Route cable through the bottom of mouting plate. 3. Tighten screws evenly. Note: please support exterior assembly during mounting plate installation. YES NO NO 4. Ensure tight cable connection. 5. Tighten screws evenly. up 2 . Install strike on the door frame. 3 St3.5 * 20s cross countersunk head tapping screw Make sure the hole in the door frame is drilled a minimum of 1"(25mm)deep. The smooth side of the plug should be at the bottom. NO NO Insert key and test latch. if latch does not extend or retract smoothly. please adjust mounting plate screws. If the keypad and mounting plate are deflection. please loose mounting plate screws and adjust. 4 Install the exterior assembly 1 2 cable YES NO 4 Route the cable through the door below The key must be pulled out when installing. the bolt.and push the keypad onto the door. 5 6 3 5 6 7 8 9 7 11 10 12 13 8 Customer Support: Phone:+1 833 553 0460 Email:support@kingforceusa.com 14 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.Adobe Illustrator 26.0 (Windows) GPL Ghostscript 9.56.1