Enterprise Fleet Management Solutions: Vehicle Tracking Software - Fleet Hoster
User Guide for FLEETHOSTER models including: AI-12, AI-14, AI-14 HOSTER Surfsight 4 Way Universal Harness Kit, HOSTER Surfsight 4 Way Universal Harness Kit, Surfsight 4 Way Universal Harness Kit, 4 Way Universal Harness Kit, Universal Harness Kit, Harness Kit
Spec Sheet & Install Guides - Fleet Hoster
File Info : application/pdf, 13 Pages, 1.19MB
DocumentDocumentFleet Hoster Surfsight® ADAS Calibration User Guide ADAS calibration from the dashcam Why does road-facing ADAS calibration matter? The Surfsight®dashcam uses Advanced Driver Assistance System (ADAS) features to gather information about the road ahead. It detects events such as: · lane weaving - your vehicle crosses over a certain number of lane marking lines in a specific amount of time · tailgating - your vehicle is driving too close to the vehicle in front of you For tailgating events, Surfsight® manages limitation parameters for time-to-collision (TTC). When the driver exceeds the configured TTC limit and for the configured duration (or longer), visual and audio alerts are sent. Users can configure the permitted TTC and duration parameters, as shown in the table below: Parameter name Descripti on Time to collision during the day (headwayAlertDayThresh old) The TTC limit during the day Time to collision during the night The TTC limit at night (headwayAlertNightThres hold) Continuous time to collision (headwayAlertTime) Note The amount of time during which the TTC can be exceeded until alerts are delivered. This value is the same for both day and night. Default values are not recommendations. Valid values (milliseconds) 1,000 to 15,000 1,000 to 15,000 1,000 to 60,000 Default values (milliseconds) 2,000 3,000 3,000 How to calibrate from the dashcam 678.759.2544 | sales@fleethoster.com | www.fleethoster.com Important The dashcam should first be installed at least 1.6 meters (160 centimeters/5.249 feet/62.99 inches) above the ground before beginning ADAS calibration. This is mandatory. Notice Enter the measurements in the units of measurement that are set for your dashcam. If your dashcam has the Speed setting set to: · kilometers per hour - enter measurements in centimeters · miles per hour - enter measurements in inches These settings can be changed from the Settings menu of the dascham, or from the Surfsight® Portal. To calibrate the road-facing ADAS through the settings menu of your dashcam: Note To recalibrate, press recalibrate under ADAS in the dashcam settings, and begin from step 8 above. 1. Drive the vehicle at above 75 km/h (46.6 mph) for around five minutes. Images from this drive are automatically obtained and saved to be used later in the calibration process. Until your vehicle is calibrated, images are obtained and saved during every drive above 75 km/h (46.6 mph). Note Installers who do not have insurance to drive client vehicles can provide the required measurements in steps 9-11 for their clients to fill in when calibrating. 2. Park the vehicle safely. 3. When you are in the parked vehicle with the parking brake on, the ignition on, and the door closed, press the touchscreen of the dashcam to view the PIN screen. 4. Enter the default PIN 3333 to unlock the dashcam for the first time, or your own PIN subsequently. 678.759.2544 | sales@fleethoster.com | www.fleethoster.com 5. The screen unlocks and the menu appears. 6. Press Settings. 678.759.2544 | sales@fleethoster.com | www.fleethoster.com 7. Scroll down to ADAS. 8. Toggle the button to turn calibration on. In the AI-12 dashcam: In the AI-14 dashcam: Press Calibrate. 9. The set up for the calibration process begins automatically. 10. Press the upper left and right arrow buttons to view various image options. These images are those obtained in step 1. Select an image where you have a clear view of the road in front of your vehicle and press OK. 678.759.2544 | sales@fleethoster.com | www.fleethoster.com 11. Enter the camera height, from the ground. Important The dashcam should first be installed at least 1.6 meters (160 centimeters/5.249 feet/62.99 inches) above the ground before beginning ADAS calibration. This is mandatory. Tip The more exact the measurements used in calibration are, the better road-facing ADAS performs. You can measure the distance from the ground to the floor of the vehicle, measure from the floor of the vehicle to the dashcam, and add the two measurements. Another option is to measure from the ground to a point parallel in height to the dashcam. Notice 678.759.2544 | sales@fleethoster.com | www.fleethoster.com Enter the measurements in the units of measurement that are set for your dashcam. If your dashcam has the Speed setting set to: · kilometers per hour - enter measurements in centimeters · miles per hour - enter measurements in inches These settings can be changed from the Settings menu of the dascham, or from the Surfsight® Portal. In the AI-12 dashcam: 12. Enter the rear axle width, from the outer edges of each tire. Notice Enter the measurements in the units of measurement that are set for your dashcam. If your dashcam has the Speed setting set to: 678.759.2544 | sales@fleethoster.com | www.fleethoster.com · kilometers per hour - enter measurements in centimeters · miles per hour - enter measurements in inches These settings can be changed from the Settings menu of the dascham, or from the Surfsight® Portal. In the AI-12 dashcam: 13. Enter the camera offset, from the center of the windshield to the road-facing lens. If the road-facing lens is to the right of the windshield center from inside the cabin, enter the measurement as a positive number. If the road-facing lens is to the left of the windshield center from inside the cabin, enter the measurement as a negative number. Notice Enter the measurements in the units of measurement that are set for your dashcam. If your dashcam has the Speed setting set to: 678.759.2544 | sales@fleethoster.com | www.fleethoster.com · kilometers per hour - enter measurements in centimeters · miles per hour - enter measurements in inches These settings can be changed from the Settings menu of the dascham, or from the Surfsight® Portal. In the AI-12 dashcam: 14. Adjust the height of the red line to mark the highest point where the dashboard or vehicle front is visible. If no part of the vehicle is visible, lower the red line to the bottom of the image. 678.759.2544 | sales@fleethoster.com | www.fleethoster.com 15. Adjust the red rectangle to mark the edges of the left and right lanes. 678.759.2544 | sales@fleethoster.com | www.fleethoster.com 16. Confirm the calibration layout. 678.759.2544 | sales@fleethoster.com | www.fleethoster.com 17. Once the calibration layout is confirmed, your dashcam calibrates. This can be seen in the Settings menu. In the AI-12 dashcam: In the AI-14 dashcam: 678.759.2544 | sales@fleethoster.com | www.fleethoster.com (678)-759-2544 | sales@FleetHoster.com | www.FleetHoster.com