Wavetronix
User Guide for WAVETRONIX models including: Click 510, Comm. Tester, Click 510 Comm. Tester, Tester
File Info : application/pdf, 4 Pages, 535.13KB
DocumentDocumentClick 510 Comm. Tester INSTALLATION QUICK START GUIDE 1 Mount the device The Click 510 mounts over a T-bus for power and communication: 1 If the Click 510 was shipped with the T-bus connector attached, remove the connector from the module. 2 Snap the connector onto the DIN rail by positioning it over the rail with the male connector pointing to the rights. Hook one arm over the edge of the DIN rail and press down on the other arm until it snaps into place. 3 Connect the T-bus connector to the rest of the T-bus by sliding them together until you hear them snap into place. 4 Mount the Click 510 onto the DIN rail: position it properly over the T-bus connector, hook the lip over the lower edge of the DIN rail, and use a rocking motion to snap the module into place. 2 Wire power and communication If you are using a Click 200 surge protector with the Click 510, power and communication are provided to the Click 10 through the T-bus (see the Click 200 Quick Start Guide). If you don't have a Click 200 surge protector, use the following steps to wire power and communication into the Click 510. 1 Plug a T-bus 5-screw terminal block into the first T-bus connector. 2 Wire DC power (1030 V) from the power supply Red (+DC) into the first screw terminal on the 5-screw terminal block; wire -DC into the second screw Black (-DC) terminal. 3 Connect RS-485 communication (+485, -485, White (+485) and GND) to either the remaining three screw terminals on the 5-screw terminal block or to the Blue (-485) screw terminals in the pluggable screw terminal block on the top of the Click 510 (see labels for Drain (GND) correct wiring). The Click 510 has three other communication ports. RJ-11 jack Connect a jumper cable here for RS-485 communication. DB-9 connector Connect a straight-through cable here for RS-232 communication. RS-232/RS-485 terminals This is on top of the device and is usually not used. www.wavetronix.com 801.734.7200 3 Use on-device configuration features Next, use the Click 510's configuration to make sure it's wired and working properly. The Click 510 has four LEDs that monitor activity and help you se- lect tasks and operating modes. It also has two banks of LEDs: one of yellow LEDs that represent LED activity indicating functions: submenu 1 and one Red Device has power Yellow Device is transmitting data Green Device is receiving data of red for submenu 2. It also has a push-button, labeled Mode Switch, also used for The blue LED has no activity-indicating function. tasks and operating modes. 1 Check the LEDs to make sure the device has power. 2 Select the baud rate for the device by autobauding as outlined below. If you'd rather manually set the baud rate, see Part 5 below. Yellow LEDs Red LEDs Multicolored LEDs Sub Menu 1 Sub Menu 2 Main Menu Button LED task-indicating functions (operating mode functions will be covered later Selection Operating mode Running Completed Autobaud Hold the push-button down. Release it when green LED is solid, then press quickly once, to autobaud to sensor. failure: will return to previous mode success (will then return to previous mode) Reset Hold the push-button down. Release it when red LED is blinking, then press quickly once, to reset to factory defaults. 4 Use the Mode Switch to navigate through mode and task menus Select a task or operation function by navigating through the main menu (multicolored LEDs) and the submenus (yellow and red LEDs) using the Mode Switch push-button as described below: 1 Enter the main menu and cycle through it by holding the 6 Press the Mode Switch again to select the function. Once Mode Switch down. selected, the function will either start running or the sec- 2 Release the Mode Switch once the cycle reaches the ond submenu (red LEDs) will start. desired function. 7 Hold the Mode Switch to cycle through the second sub- 3 Press the Mode Switch again to select the function. Once menu. selected, the function will either start running or the first 8 Release the Mode Switch once the desired submenu submenu (yellow LEDs) will start. selection is displayed. 4 Hold the Mode Switch to cycle through the first submenu. 9 Press the Mode Switch again to select the function. The 5 Release the Mod Switch once the desired menu selection function will now run. is displayed. 5 Manually set baud rate (optional) Note. This step is optional because if you prefer not to select the baud rate manually, you can also autobaud the device (see part 3 of this guide). 1 Hold the Mode Switch down, then release when the green LED starts flashing. 2 Press the Mode Switch again to select the baud rate task. The LED indicating the current baud rate will turn on (see table). 3 Hold down the Mode Switch. The yellow LEDs will cycle through the eight possible baud rates, first by lighting up solid and then by flashing, as shown in the table below. 1st LED 2nd LED 3rd LED 4th LED Submenu 1 (Yellow LEDs) 1 second 0.25 1 second Switch (when push- button is pressed) Submenu 2 (Yellow LEDs) 17"60' 3060 mph Random traffic Diagnostic traffic - 4 Once you reach the baud rate you want, release the push-button, then press it once to select. 5 The device will return to the operating mode it was in before you started the baud rate task. 6 First test mode: Sensor Emulation Sensor Emulation mode tests connection between a sensor and other devices. The Click 510 can mimic a SmartSensor 105 and send traffic data, allowing you to see if breaks in communication are caused by the communication channel or by the sensor itself. It also allows you to check the functionality of an assembled traffic cabinet before attaching a sensor. In both of these cases, the device should be connected to a contact closure module such as the Click 100 or 172/174 so the response can be monitored. 1 Hold the push-button down, then release when the blue LED starts flashing. 2 Pres the push-button to select. The first yellow LED will turn on to let you use that submenu. 3 To pick how often the device wills end data, hold down the push-button and it will cycle through the time options shown in the table below. Release when you reach one you want. 4 Press the push-button to select. The first red LED will turn on to let you use that submenu. 5 To pick what kind of data the device will send, hold down the push-button and it will cycle through the traffic options shown in the table below. Release when you reach one you want. 6 Press the push-button to select. 1st LED Submenu 1 (Yellow LEDs) 1 second 2nd LED 0.25 1 second Submenu 2 (Yellow LEDs) 17"60' 3060 mph Random traffic 3rd LED Switch (when pushbutton is pressed) Diagnostic traffic 4th LED - - 7 Connect the device to a contact closure device, such as a Click 172/174. Set up the contact closure device (see the pertinent quick start guide) and the mode will begin to run. As the mode runs, the blue LED will flash fast and the submenu LEDs will light up if the Click 510 is pushing data. Monitor the contact closure device to see if data is received. 7 Second test mode: Test Pattern Test Pattern mode tests communication channels by sending data packets over the channel. It's helpful for debugging because it locates the break in your channel of communication. To use it, connect two Click 510 devices together or connect a Click 510 to a computer. The responses can be monitored with serial terminal software or by watching the LEDs on the receiving 510. 1 Hold the push-button down, then release when the blue LED comes on solid. 2 Press the push-button to select. The first yellow LED will turn on to let you use that submenu. 3 To pick how often the device will send data, hold down the push-button and it will cycle through the time options shown in the table below. Release when you reach one you want. 4 Press the push-button to select. The first red LED will turn on to let you use that submenu. 5 To pick what kind of data the device will send, hold down the push-button and it will cycle through the traffic options shown in the table below. Release when you reach one you want. 6 Press the push-button to select. The mode will run. Observe the connected Click 510 or computer to monitor that the packets are being received. 1st LED Submenu 1 (Yellow LEDs) 1 second Submenu 2 (Yellow LEDs) LED flash 2nd LED 0.25 1 second LED sequence 3rd LED Switch (when pushbutton is pressed) ASCII sequence 4th LED - ASCII text See the Click Series User Guide for more information. 8 Third test mode: Latency Test This test measures the time it takes data packets to travel across your communication channel. For this mode, two Click 510 devices must be connected, with both of them set in this mode. 1 On both devices, hold the push-button down, then release when the yellow LED is solid. 2 Press both push-buttons to select. The results from the last latency test will appear in the LEDs. 3 Press the push-button again on either one of the devices to start the test. 4 While the test runs, the red and yellow LEDs will flash as the 510 tries different packet sizes. When the test is finished, the results can be viewed in two ways: Before the test, connect via serial from a computer to the device that is initiating the test, then after the test, look at the results in a serial terminal program. Look at the LEDs on the device running the test. See the graphic to the right for what the LEDs mean. Each red flash = 100 msec delay Each red flash = 1 sec delay Timed out or corrupt data See the Click Series User Guide for more information. © 2022 Wavetronix LLC. All rights reserved. Protected in the US by patents viewable at www.wavetronix.com/en/legal. Protected by Canadian Patent Nos. 2461411; 2434756; 2512689; and European Patent Nos. 1435036; 1438702; 1611458. Other US and international patents pending. Wavetronix, SmartSensor, Click, Command and all associated logos are trademarks of Wavetronix LLC. All other product or brand names as they appear are trademarks or registered trademarks of their respective holders. Product specifications are subject to change without notice. This material is provided for informational purposes only; Wavetronix assumes no liability related to its use. WX-500-0194